Display - JVC SR-9090U - High Resolution 960 Hour Density Instructions Manual

2 CONTROLS AND CONNECTORS

2-2 Display

1
2 3
1
Operation mode display
Shows the operation modes.
Playback Recording Rewind
Record- Rewind
Still
pause search
* ( ) mark in the Rec/Pause mode is shown in red.
2
Cassette indication
Lights when a cassette is loaded. Blinks when a cassette
is being ejected.
3
[SP/EP] indication
Shows the standard (SP) mode or extended (EP) mode
during recording/playback.
recording/playback, the [SP] indication is shown.
The [EP] indication is shown during recording in the HDR
(High-Density Record) mode or during playback of a tape
section recorded in the HDR mode.
4
Tape counter/clock indication
• Shows the current time (hour: minute: second), tape
control counter (00H 00M 00S — 23H 59M 59S) or tape
reel counter (0 — 9999) when the operating mode is on.
The display can be selected with the [DISPLAY] button.
Shows the current time when the operating mode is off.
When a cassette is ejected, the tape control counter and
tape reel counter are reset automatically.
• When the cassette is rewound to the beginning in the
Repeat Recording or Auto Rewind mode using the counter
end output function, the tape control counter and tape
reel counter are reset.
• The control and reel counter counts slowly in the Timelapse
mode.
• In the timelapse mode, the control counter shows the time
equivalent to that shown when a tape is played back in the
2H or 6H mode.
(Example: The control counter advances 1 second for
about 8 minutes in the 960H ordinary timelapse mode.)
• During date/time search setting and operation, "td" is
shown in place of the seconds.
• Shows the setting item during menu switch setting.
7
6 8
Timelapse
Fast-
forward playback
Fast-forward Reverse
search playback
During ordinary timelapse
10
9 11 12
4
5
Recording/playback speed display
• Normally shows the recording/playback speed mode set
with the [TIME MODE] button.
• Shows the following indications in the Alarm Search
mode.
During alarm search: Shows the specified alarm number
(example: AL12)
During alarm scan: Shows the alarm scan mode (ALSC).
During date/time search: Shows the specified date and
time (example 2310).
• Shows setting details in menu switch setting.
• When an error occurs, the error indication "E-**" blinks (if
the menu switch <WARNING> on the <F. DISP> screen
is set to "ON").
For error indications, refer to page 53.
6
[TIMER] indication
Lights during timer recording programming/operation.
7
[REPEAT] indication
When <REPEAT REC> in the <VTR MODE> menu is set
to "ON", this indication is shown. When <TAPE END
MODE> in the <ALARM/SENSOR MODE> menu is set to
"STOP" and the Repeat Record mode is engaged, the
[REPEAT] indication goes out if alarm recording or sensor
recording takes place.
8
[OVERLAP] indication
Blinks when programs scheduled for timer recording overlap.
9
Timer program number
All programmed timer recording numbers light.
During timer recording, the number of the program being
recorded blinks. When the timer recording ends, this
number goes out.
0
[AL] (alarm) indication
Shown during alarm recording or sensor recording.
Blinks when alarm recording or sensor recording ends.
!
[LOCK] indication
Lights when the operation lock function is activated.
@
[AL REC] (alarm recording) indication
Lights when the menu switch <REC MODE> on the <ALARM/
SENSOR MODE> screen is set to "ALARM" or "ALL".
#
[SENSOR REC] (sensor recording) indication
Lights when the menu switch <REC MODE> on the <ALARM/
SENSOR MODE> screen is set to "SENSOR" or "ALL".
13 13
5
11