Connecting To Video Equipment With Rgb Or S-Video Inputs; Connecting Two Or More Cameras-Multi-Camera System - Sony DXC-390 Service Manual

Basic System Connection

Connecting to Video Equipment with RGB or S-Video Inputs

DC IN/VBS
DXC-390/390P
VIDEO OUT
DC IN/VBS
TRIG IN
LENS
MENU LOCK
OFF ON
RGB/SYNC
REMOTE
*If a CCMC cable is used, the S-video signal is also output from the S-video output of the CMA-D2/D2MD/D2CE/D2MDCE.
1) When using a video monitor without a sync signal input connector, the
camera can be set to output a sync signal with the G signal or RGB
signals.
For details, see "SYSTEM menu" on page 27.
50
(GB) Chapter 3 Installation and Connections
Connecting Two or More Cameras—Multi-Camera System
Notes on multi-camera system
Perform the following to prevent flicker when switching
between two or more cameras connected to a video
switcher:
• Supply the same sync signal to the GENLOCK IN
Sync signal generator
Sync (VBS or
BS) output
VBS OUT
VIDEO IN
Video monitor,
VTR, etc.
1-26 (E)
CCDC-5/10/25/50A/100A cable or
CCMC-12P02/05/10/25 cable*
Camera cable: CCXC-9DB (D-sub 9-pin
y BNC connectors), or CCMC-9DS (D-
sub 9-pin y BNC, S-video connectors)
RGB/SYNC
or
Camera cable CCXC-9DD
(D-sub 9-pin y D-sub 9-pin)
75-ohm coaxial cable
DXC-390/390P
VIDEO OUT
DC IN/VBS
TRIG IN
LENS
MENU LOCK
OFF ON
RGB/SYNC REMOTE
VIDEO IN
DC IN/VBS
Switcher, etc.
VBS OUT
75-ohm coaxial cable
DXC-390/390P
OUT
VIDEO OUT
DC IN/VBS
TRIG IN
LENS
MENU LOCK
OFF ON
RGB/SYNC
REMOTE
DC IN/VBS
1
Set the MODE selector
CMA-D2/D2MD/D2CE/
to the "1" position.
2
D2MDCE camera adaptor
CAMERA (4-pin or 12-pin)
R input
G input
B input
Sync input
Composite video (BNC) or
2)
S-video input (4-pin)
RGB/SYNC input
2) This setup is for connecting to a composite video (VBS) connector. To
output separated Y/C signals to the S-video input of video equipment,
use a CCMC-9DS camera cable.
For details on switching camera output between VBS (composite video) and
Y/C, see "SYSTEM menu" on page 27.
connectors on each camera adaptor (see below).
• Adjust the subcarrier and horizontal synchronization
phases for all cameras.
For more details, see "Adjusting the Picture Tone in a
Multi-Camera System" on page 41.
Set the MODE selector
1
to the "1" position.
2
VIDEO
GENLOCK IN
OUT
CAMERA (12-pin)
CCMC-12P02/05/10/25 cable
Set the MODE selector
1
to the "1" position.
2
VIDEO
GENLOCK IN
CAMERA (12-pin)
CCMC-12P02/05/10/25 cable
Chapter 3 Installation and Connections
Power cord
RGB monitor,
image processor,
etc.
1)
Computer, image
processor etc.
CMA-D2/D2MD/
D2CE/D2MDCE
camera adaptor
Power cord
CMA-D2/D2MD/
D2CE/D2MDCE
camera adaptor
Power cord
51
(GB)
DXC-390/390P