Recording Playback Signals From A Dv Camera Or Vcr - JVC BD-X200U - Dvd Authoring Recorder Instructions Manual

Recording Playback Signals From a DV Camera or VCR

DV (IEEE1394) control can be used to record playback signals from a camera or VCR with a DV terminal to a disc in your BD-X200.
It will then be possible to control that VCR using this DVD recorder's REMOTE CONTROL screen.
Signal Connections
Rear panel
VIDEO OUT
LAN
SIGNAL
USB terminal
Keyboard
Esc F1 F2 F3 F4 F5 F6 F7 F8
1 2 3 4 5 6 7 8 9 0
Q W E R T Y U I O P
Tab
Caps Lock A S D F G H J K L
Z X C V B N M < >
Shift
,
Ctrl Alt Alt
Connect the DV IN/OUT terminal on the rear of your BD-X200 to the DV terminal on the DV camera or VCR using a DV (IEEE1394)
cable. One of the commercially-available cables indicated above should be used for this purpose.
Connect the DVD recorder's VIDEO LINE OUT and AUDIO OUT terminals to the monitor's video in and audio in terminals.
A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL screen.
If used, these are to be connected to each of the USB terminals on the rear panel.
Setup Procedures
Insert the tape for playback into the camera or VCR. Ensure that this tape contains an SMPTE time code.
Insert a recordable disc into your BD-X200.
Settings
DV camera or VCR : Enable control via DV.
BD-X200 : Set REMOTE SELECT from the REMOTE MENU screen to DV (MASTER).
REMOTE MENU screen
REMOTE MENU
MENU
REMOTE SELECT
REC CONTROL
REM FF/REW MODE
Note
When pressing and holding the REC
button more than 2 seconds while the DVD
recorder is stopped, encoded output
images can be checked while the button
is being held.
AUDIO OUT
VIDEO AUDIO
IN LINE OUT INPUT CH1
LEVEL
IN OUT
4dB
8dB
Y/C
IN
CH2
DV IN/OUT terminal
REMOTE
DV IN/OUT
USB
DC 19V (video, audio, and control signals)
GND
Print Pause
Scroll
F9 F10 F11 F12 Screen
Lock
Sysrq Break
Back Page Num
Insert Home *
- Space Up Lock
^
7 8 9
Enter Page
Delete End
@ Down
+
4 5 6
;
:
Mouse
? 1 2
Shift
/
Enter
.
0
Ctrl
When REMOTE SELECT is set to DV (MASTER), the REMOTE CONTROL (DV
MASTER) screen will appear. This screen is used to perform editing operations,
and the corresponding operations are described on pages 60 through 62.
DV(MASTER)
OFF
FF/REW
Monitor
DV terminal
DV cables:
VC-VDV204 (2 m, 4P-4P) from JVC
VC-VDV206 (2 m, 4P-6P) from JVC
REMOTE CONTROL (DV MASTER) screen
REMOTE CONTROL SCREEN ( DV MASTER )
EXIT IN POINT 00:00:00:00
: : : :
h m s f h
1 00:00:00:00 2 00:15:00:00
4 00:25:00:00 5 00:30:00:00
7 8
00:40:00:00 00:45:00:00
CHAPTER MANUAL
ADJ
8.0 Mbps
BITRATE
TC SET
EDL LOAD
TC CANCEL EDIT/END
DV camera or VCR
MIC 2 IN
VIDEO OUT
Monitor
00:10:00:00
OUT POINT
: : : : :
m s f h m s f
3 00:20:00:00
6 00:35:00:00
9
00:50:00:00
: : :
TC INPUT
000 min
DISC REMAIN
FINALIZE
MIC 1 IN
63