JVC BD-X200U - Dvd Authoring Recorder Instructions Manual page 62

Synchronous Recording
Recording Playback Signals From a VCR with RS-422A (continued)
Editing Via the REMOTE CONTROL (9PIN MASTER/DV MASTER) Screen
A keyboard and mouse can be used as an alternative to the DVD recorder's buttons when using the REMOTE CONTROL (9PIN
MASTER/DV MASTER) screen.
Front panel : Select using the cursor buttons (t, 8, 7, and 6), and confirm the selection using the SET button.
: Select using the arrow keys (†, ©, √, and ∞), and confirm the selection using the Enter key.
Keyboard
Mouse : Left click the required button.
* When the REMOTE CONTROL screen is being displayed, the DVD recorder's, FWD, REV, PLAY, REC, PAUSE, MENU, and TOP
MENU buttons will be disabled.
In Point (start point for editing):
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be started.
Chapter list:
This displays the time
codes of chapter
marks.
The In Point's time
code is registered as
the first chapter
mark.
A total of 98 chapters
can be setup.
When CHAPTER
CREATION from the
RECORDER MENU
(2/2) screen is set to
MANUAL, it will be
possible to setup
chapter marks at any
position on the
playback tape.
CHAPTER:
The right-hand field indicates
the current setting for
CHAPTER CREATION from
the RECORDER MENU (2/2)
screen.
When set to MANUAL,
chapter marks can be
registered in this screen's
chapter list.
When set to AUTO, the
DVD recorder's chapter
auto-create function will set
chapters. In such a case, it
will not be possible to
register chapters using this
screen's chapter list.
Chapter marks
inserted at GOP intervals
(i.e., 15 frames). It will not
be possible to inser t
chapter marks that are
closer together than this
interval.
60
REMOTE CONTROL SCREEN ( 9PIN MASTER )
EXIT IN POINT
: : :
h m s
f
1 00:00:00:00
4 00:25:00:00
7 00:40:00:00
CHAPTER
ADJ
BITRATE
TC SET
TC CANCEL
ADJUST:
This button can be
pressed to determine
the remaining disc time
based on the editing
time and to also set a
suitable bit rate. This
setting is then
displayed in the BIT
RATE field.
VCR Control Panel
The buttons provided in this panel are used to control VCR operations. When a
button is selected and confirmed, the VCR will carry out the corresponding operation.
It is important to remember that these buttons do not control operation of this DVD
recorder.
are
e : Eject
u : Fast reverse or fast-reverse play
: Frame-Reverse play
q
: Stop
* The action to be taken by the DVD recorder in response to pressing of the y or
u button (i.e., FF/REW or SEARCH) is selected using REM FF/REW MODE
from the REMOTE MENU screen.
Out Point (end point for editing):
Set the time code (hours : minutes : seconds : frames) of
the position on the playback tape where recording is to
be stopped.
00:00:00:00
OUT POINT
: : : :
h m s h m
f
2 00:15:00:00 3 00:20:00:00
5 00:30:00:00 6 00:35:00:00
8 00:45:00:00 9 00:50:00:00
:
TC INPUT
MANUAL
8.0 Mbps DISC REMAIN
FINALIZE
EDL LOAD
EDIT/END
TC SET : This button is used to set input time codes for
TC CANCEL : This button is used to remove setting values
EDL LOAD : This button is used to load the most-recent
EDIT/END : This button is used to start editing
w : Pause
t : Play
y : Fast forward or fast-forward play
TC INPUT:
This field is used to input
time codes for the In
00:10:00:00
Point, Out Point, and
chapter marks from the
: :
s
f
keyboard.
DISC REMAIN:
: :
This field shows an
estimate of the remaining
000 min
space for recording on the
disc.
FINALIZE:
This button is used to
finalize the disc.
the In Point, Out Point, and chapter marks.
for the In Point, Out Point, and chapter marks.
edit list. It can be used whenever CREATION
CHAPTER has been set to MANUAL.
automatically. When recording has ended, the
DVD recorder automatically adopts Recording
STOP mode. If selected while editing, this
button will end that process.
: Frame-advance play