Page 2
Thank you for purchasing the Wireless MPEG4/MJPEG Network Camera, a powerful dual‐codec wireless network camera with the 1‐way or 2‐way audio function that provides the high‐quality image and on‐the‐spot audio via the Internet connection. The Infrared LEDs and light sensor (optional) enable the camera to capture images even in the dark environment. The camera can be installed as a standalone system within your application environment easily and quickly, and supports remote management function so that you can access and control it using a Web browser on your PC. This Advanced Installation Guide provides you with the instructions and illustrations on how to use your camera, which includes: Chapter 1 Introduction to Your Camera describes the features of the camera. You will also know the components and functions of the camera. Chapter 2 Hardware Installation helps you install the camera according to your application environment. You can use this camera at home, at work, at any where you want. Chapter 3 Accessing the Camera lets you start using your camera without problem. The camera can be set up easily and work within your network environment instantly. Chapter 4 Configuring the Camera guides you through the configuration of the camera using the web browser on your PC. Chapter 5 Appendix provides the specification of the camera and some useful information for using your camera. NOTE The illustrations and configuration values in this guide are for reference only. The actual settings depend on your practical application of the camera. - 1 -...
Contents PREFACE ................. 0 CHAPTER 1 .............. 4 INTRODUCTION TO YOUR CAMERA ...... 4 1.1 C ..........4 HECKING THE ACKAGE ONTENTS 1.2 G ..........5 ETTING TO NOW OUR AMERA 1.3 F ............7 EATURES AND ENEFITS 1.4 S ...
Page 4
4.8 E ................42 VENT ONFIG 4.9 T ...................46 OOLS 4.10 USB ..................48 4.11 D ................50 EVICE CHAPTER 5 .............. 5 2 SECURVIEW™ PRO SOFTWARE ......... 5 2 5.1 I .................53 ...
1 HAPTER NTRODUCTION O OUR AMERA 1.1 Checking the Package Contents Check the items contained in the package carefully. You should have the following: One TV‐IP312WN One Power Adapter One External Antenna One Camera Stand/Mounting Kit One Network Cable One CD‐ROM (Utility & User’s Guide) One Multi‐Language Quick Installation Guide NOTE Once any item contained is damaged or missing, contact the authorized dealer of your locale. - 4 -...
1.2 Getting to Know Your Camera Power LED indicates the camera is powered on with the steady Internal Microphone amber light. allows the camera to receive sound and voice. Infrared LEDs (optional) allows your camera to Link LED indicates capture clear image in a the camera’s network dark environment.
Page 7
Antenna Screw Hole is used to connect the camera stand. Audio-out Connector is used to connect an external active speaker. Ethernet Cable Connector is used to connect the network cable, which supports the Auto- MDIX so that the camera can ...
1.3 Features and Benefits MPEG4/MJPEG Dual‐codec Supported The camera provides you with excellent images by the MPEG4/MJPEG dual‐codec selectable technology, allowing you to adjust image size and quality, and bit rate according to the networking environment. 2‐way Audio Capability The built‐in microphone of the camera provides on‐the‐spot audio via the Internet, allowing you to monitor the on‐site voice. In addition, you can connect an external speaker to the camera to speak through the camera; the camera is embedded with an echo cancellation processor to provide a better sound quality. Day & Night Surveillance Supported (optional) The six Infrared LEDs around the standard lens enable the camera to capture crystal clear images in the dark environment or at night. When the Light Sensor detects the environmental light level becomes low, the camera captures the images in black & white mode using these infrared LEDs. Supports Multiple Profiles The camera supports multiple profiles simultaneously, so that you can separately set up different image settings (such as image quality and frame rate) for the three video types of the camera: MPEG4, MJPEG, and 3GPP. Supports RTSP The camera supports RTSP (Real Time Streaming Protocol), which is a technology that allows you to view streaming media via the network. You can view the real‐time video with the Quick Time player or RealPlayer. To view the real‐time streaming image on your computer, open the Web browser and enter the RTSP link: rtsp://(IP address of the camera)/3gp. - 7 -...
Page 9
Remote Control Supported By using a standard Web browser or the bundled SecurView Pro software application, the administrator can easily change the configuration of the camera via Intranet or Internet. In addition, the camera can be upgraded remotely when a new firmware is available. The users are also allowed to monitor the image and take snapshots via the network. Supports Connection to the External Devices With the auxiliary Input/Output connectors, you can connect the camera to a variety of external devices, such as the external speaker and the USB device. Multiple Platforms Supported The camera supports multiple network protocols, including TCP/IP, SMTP e‐mail, HTTP, and other Internet related protocols. Therefore, you can use the camera in a mixed operating system environment, such as Windows Vista and Windows 7. Multiple Applications Supported Through the remote access technology, you can use the cameras to monitor various objects and places for your own purposes. For example, babies at home, patients in the hospital, offices and banks, and more. The camera can capture both still images and video clips, so that you can keep the archives and restore them at any time. - 8 -...
1.4 System Requirement Networking LAN: 10Base‐T Ethernet or 100Base‐TX Fast Ethernet. WLAN: IEEE 802.11b/g, Based on IEEE 802.11n technology. Accessing the Camera using Web Browser Platform: Microsoft® Windows® 2000/XP/Vista/Win7 CPU: Intel Pentium III 800MHz or above RAM: 512MB Resolution: 800x600 or above User Interface: Microsoft® Internet Explorer 6.0 or above Accessing the Camera using SecurView Pro Platform: Microsoft® Windows® XP/Vista/Win7 Resolution: 1024x768 or above Hardware Requirement: 1~8 cameras: Intel Core 2 Duo 2GB RAM 9~32 cameras: Intel Core 2 Quad 4GB RAM NOTE If you connect multiple cameras to monitor various places simultaneously, you are recommended to use a computer with higher performance. - 9 -...
2 HAPTER ARDWARE NSTALLATION 2.1 Installing the Camera Stand The camera comes with a camera stand, which uses a swivel ball screw head to lock to the camera’s screw hole. When the camera stand is attached, you can place the camera anywhere by mounting the camera through the three screw holes located in the base of the camera stand. The Camera Stand/Mounting Kit - 10 -...
2.2 Connecting the Camera to LAN/WLAN Use the provided Ethernet cable to connect the camera to your local area network (LAN). When you connect the AC power adapter, the camera is powered on automatically. You can verify the power status from the Power LED on the front panel of the camera. Once connected, the Link LED starts flashing green light and the camera is on standby and ready for use now. Connecting the Ethernet Cable If you use a wireless network in your application environment, you need to attach the included external antenna to the camera. When the camera is powered on, the camera will automatically search any access point with “default” SSID. Connecting the External Antenna NOTE If the camera cannot to your wireless network, you need to install the camera in LAN and proceed with WLAN settings. - 11 -...
2.3 Applications of the Camera The camera can be applied in multiple applications, including: Monitor local and remote places and objects via Internet or Intranet. Capture still images and video clips remotely. Upload images or send email messages with the still images attached. The following diagram explains one of the typical applications for your camera and provides a basic example for installing the camera. *Please enclosed by waterproof housing when using in outdoor Home Applications - 12 -...
3 HAPTER CCESSING THE AMERA 3.1 Using IP Setup The camera comes with a conveniently utility, IP Setup, which is included in the Installation CD‐ROM, allowing you to search the camera on your network easily. 1. Insert the Installation CD‐ROM into your computer’s CD‐ROM drive to initiate the Auto‐Run program. 2. Click the IP Setup button to launch the utility. The control panel will appear as below. Display the connected camera(s). Double click to link the Camera. Click About to get the Version information of IPSetup. Click Link to connect the selected camera. Click Change IP to modify the IP address of the selected camera.
3.2 Accessing to the Camera Whenever you want to access the camera: 1. Since the default configuration of the camera is DHCP mode enabled, you are recommended to launch IP Setup to search the IP address that is assigned to the camera by the DHCP server, and then click Link to access the camera via the Web browser. 2. If Network Camera can't get IP Address under DHCP mode, the default IP Address will be 192.168.10.30. 3. When the login window appears, enter the default User name (admin) and password (admin) and press OK to access to the main screen of the camera’s Web Configuration. Enter the User name and Password. NOTE If you are initially access to the camera, you will be ask to install a new plug‐in for the camera. Permission request depends on the Internet security settings of your computer. Click Yes to proceed. - 14 -...
Page 16
After you login into the Web Configuration of the camera, the main page will appear as below: Zoom In Buttons Camera Information Live View/Setup Switch Nightmode Button Compression Buttons Function Buttons Live View Image The main page of the Web Configuration provides you with many useful information and functions, including: – Camera Information Display the camera’s location and the current date & time. The information can be modified in the Web Configuration. – Live View Image Displays the real‐time image of the connected camera. - 15 -...
Page 17
– Live View/Setup Switch Click Setup to configure the camera. For details, see Chapter 4 and Click the Live View button to return to the Main screen to view the live view image. – Compression Buttons Select to transmit and record the video using MPEG4 or MJPEG compression. – Function Buttons Use these buttons to control the audio and video functions. Manual Record allows you to record and save a video clip. Snapshot allows you to capture and save a still image. Browse allows assign the destination folder to store the video clips and still images. Talk allows you to speak out through the camera. Please note that this button displays only for the 2‐way audio model, and only one user is allowed to use this function at a time. Listen allows you receive the on‐site sound and voice from the camera. – Zoom In Buttons Click the buttons to zoom in the live view image by 1x, 2x, and 3x. – Nightmode Button Click the button to enable the “night shot mode” to deliver clearer images in the dark environment. However, this will reduce the frame rate of video setting. NOTE If your PC use Microsoft Vista platform. Maybe you can’t find these recorded files what stored by Snapshot or Manual Record. That you need to disable the protected mode of Security in the IE Browser. Please follow as below Steps: 1. Open IE Browser 2. Select Tools Internet Options 3. Select Security 4. Disable the ”Enable Protected Mode” then press OK - 16 -...
3.3 Configuring the IP Address of the PC If you are failed to access to the camera, please check the IP address of your computer. When you connect the camera to your computer directly to proceed with configuration of the camera, you need to set up the IP addresses to be in the same segment for the two devices to communicate. 1. On your computer, click Start > Control Panel to open the Control Panel window. 2. Double‐click Network Connection to open the Network Connection window. 3. Right‐click Local Area Connection and then click Properties from the shortcut menu. 4. When the Local Area Connection Properties window appears, select the General tab. 5. Select Internet Protocol [TCP/IP] and then click Properties to bring up the Internet Protocol [TCP/IP] Properties window. 6. To configure a fixed IP address that is within the segment of the camera, select the Use the following IP address option. Then, enter an IP address into the empty field. The suggested IP address is 192.168.10.x (x is 1~254 except 30), and the suggested Subnet mask is 255.255.255.0. 7. When you are finished, click OK. - 17 -...
4 HAPTER ONFIGURING THE AMERA 4.1 Using the Web Configuration You can access and manage the camera through the Web browser and the provided software application SecurView Pro. This chapter describes the Web Configuration, and guides you through the configuration of the camera by using the web browser. To configure the camera, click Setup on the main page of Web Configuration. The Web Configuration will start from the Basic page. - 18 -...
The Web Configuration contains the settings that are required for the camera in the left menu bar, including Smart Wizard, Basic, Network, Video/Audio, Event Server, Motion detect, Event Config, Tools, USB, and Information. 4.2 Using Smart Wizard The camera’s Smart Wizard lets you configure your camera easily and quickly. The wizard will guide you through the necessary settings with detailed instructions on each step. To start the wizard, click Smart Wizard in the left menu bar. Step 1. Camera Settings Enter the name for the camera and place. Enter the administrator password. - 19 -...
Page 21
Step 2. IP Settings Select the IP setting according to your network: DHCP, Static IP, or PPPoE. Step 3. Email Settings Enter the required information to be able to send email with image. - 20 -...
Page 22
Step 4. Wireless Networking Complete the required settings for wireless networking. - 21 -...
Page 23
Step 5. Confirm Settings This step shows the configuration of your camera. When you confirm the settings, click Apply to finish the wizard and reboot the camera. Otherwise, click Prev to go back to the previous step(s) and change the settings; or click Cancel to end the wizard and discard the changes. - 22 -...
4.3 Basic Setup The Basic menu contains three sub‐menus that provide the system settings for the camera, such as the Camera Name, Location, Date & Time, and User management. Basic >> System Basic - Camera Name: Enter a descriptive name for the camera. - Location: Enter a descriptive name for the location used by the camera. Indication LED This item allows you to set the LED illumination as desired. There are two options: Normal and OFF. Basic >> Date & Time Date & Time - TimeZone: Select the proper time zone for the region from the pull‐ down menu. - Synchronize with PC: Select this option and the date & time settings of the camera will be synchronized with the connected computer. - Synchronize with NTP Server: Select this option and the time will be synchronized with the NTP Server. You need to enter the IP address of the server and select the update interval in the following two boxes. - Manual: Select this option to set the date and time manually. - 23 -...
Page 25
Basic >> User Administrator To prevent unauthorized access to the camera’s Web Configuration, you are strongly recommend to change the default administrator password. Type the administrator password twice to set and confirm the password. General User - User Name: Enter the user’s name you want to add to use the camera. - Password: Enter the password for the new user. When you are finished, click Add/Modify to add the new user to the camera. To modify the user’s information, select the one you want to modify from UserList and click Add/Modify. - UserList: Display the existing users of the camera. To delete a user, select the one you want to delete and click Delete. Guest - User Name: Enter the guest’s name you want to add to use the camera. - Password: Enter the password for the new guest. - UserList: Display the existing guests of the camera. To delete a user, select the one you want to delete and click Delete. NOTE The “General User” can access the camera and control the Function buttons of the camera’s Web Configuration; the “Guest’ can only view the live view image from the main page of the Web Configuration while accessing the camera. Only the “Administrator” is allowed to configure the camera through the Web Configuration. - 24 -...
Direct Video Stream Authentication To steam the video directly without going through the configuration page, you can access it via http://cameraIP/jpgview.htm (eg. http://192.168.10.30/jpgview.htm) - Enable: User needs to enter user name and password to stream the camera. - Disable: User can stream the camera without entering the user name and password. NOTE This feature is enabled by default, and for security reason, it is recommended to have the feature enabled at all time. - 25 -...
4.4 Network Settings The Network menu contains three sub‐menus that provide the network settings for the camera, such as the IP Setting, DDNS Setting, IP Filter, and Wireless network. - 26 -...
Page 28
Network >> Network IP Setting This item allows you to select the IP address mode and set up the related configuration. - DHCP: Select this option when your network uses the DHCP server. When the camera starts up, it will be assigned an IP address from the DHCP server automatically. - Static IP: Select this option to assign the IP address for the camera directly. You can use IP Setup to obtain the related setting values. IP Enter the IP address of the camera. The default setting is 192.168.10.30. Subnet Mask Enter the Subnet Mask of the camera. The default setting is 255.255.255.0. Default Gateway Enter the Default Gateway of the camera. The default setting is 192.168.10.1. In most cases, this would be your router’s IP address. Primary/ DNS (Domain Name System) translates domain Secondary DNS names into IP addresses. Enter the Primary DNS and Secondary DNS that are provided by ISP. - PPPoE: Select this option when you use a direct connection via the ADSL modem. You should have a PPPoE account from your Internet service provider. Enter the User Name and Password. The camera will get an IP address from the ISP as starting up. NOTE Once the camera get an IP address from the ISP as starting up, it automatically sends a notification email to you. Therefore, when you select PPPoE as your connecting type, you have to set up the email or DDNS configuration in advance. - 27 -...
Page 29
DDNS Setting With the Dynamic DNS feature, you can assign a fixed host and domain name to a dynamic Internet IP address. Select the Enable option to enable this feature. Then, select the Provider from the pull‐ down list and enter the required information in the Host Name, User Name, and Password boxes. Please note that you have to sign up for DDNS service with the service provider first. UPnP The camera supports UPnP (Universal Plug and Play), which is a set of computer network protocols that enable the device‐to‐device interoperability. In addition, it supports port auto mapping function so that you can access the camera if it is behind an NAT router or firewall. Select the Enable option to enable this feature. Ports Number - HTTP Port: The default HTTP port is 80. - RTSP Port: Configure the transmission of streaming data within the network. The default RTSP (Real Time Streaming Protocol) port is 554. NOTE If the camera is behind an NAT router of firewall, the suggested to be used is from 1024 to 65535. - 28 -...
Page 30
Network >> IP Filter The IP Filter setting allows the administrator of the camera to limit the users within a certain range of IP addresses to access the camera. Start/End IP Address Assign a range of IP addresses that are not allowed to access the camera by entering the Start IP address and End IP address. When you are finished, click Add to save the range setting. You can repeat the action to assign multiple ranges for the camera. For example, when you enter 192.168.10.50 in Start IP Address and 192.168.10.80 in End IP Address, the user whose IP address located within 192.168.10.50 ~ 192.168.10.80 will not be allowed to access the camera. Deny IP List The list displays the range setting(s) of IP addresses that are not allowed to access the camera. To clear the setting, select a range of IP addresses from the list and click Delete. Network >> Wireless Setting Wireless The camera supports WLAN while you use the wireless network. Select the Enable option to enable this feature. - Network ID (SSID}: Keep the default setting of this option to connect the camera to any access point under the infrastructure network mode. To connect the camera to a specified access point, set a SSID for the camera to correspond with the access point’s ESS‐ ID. To connect the camera to an - 29 -...
Page 31
Ad‐Hoc wireless workgroup, set the same wireless channel and SSID to match with the computer’s configuration. Click Site Survey to display the available wireless networks, so that you can easily connect to one of the listed wireless networks. List of searching results - Wireless Mode: Select the type of wireless communication for the camera: Infrastructure or Ad‐Hoc. - Channel: Select the appropriate channel from the list. - Authentication: Select the authentication method to secure the camera from being used by unauthorized user: Open, Shared‐key, WPA‐PSK, and WPA2‐PSK. The following table explains the four options: Open The default setting of Authentication mode, which communicates the key across the network. Shared‐key Allow communication only with other devices with identical WEP settings. WPA‐PSK/ Users have to manually enter the encryption in their WPA2‐PSK access point or wireless router, as well as in each PC on the wireless network. - 30 -...
Page 32
If you select Open or Shared‐key as the Authentication mode, you need to complete the following settings: Encryption: Select the WEP option to enable the data encryption feature to secure the camera within the wireless network. Format: Once you enable the Encryption feature, you need to determine the encryption format by selecting ASCII or HEX. ASCII format causes each character you type to be interpreted as an eight‐bit value. Hex format causes each pair of characters you type to be interpreted as an eight‐bit value in hexadecimal (base 16) notation. Key Length: Select the WEP key length you use: 64 bits or 128 bits. WEP Key 1/2/3/4: Enter the WEP key(s) in the following boxes. If you select WPA‐PSK or WPA2‐PSK as the Authentication mode, you need to complete the following settings: Encryption: Select TKIP or AES. TKIP (Temporal Key Integrity Protocol) changes the temporal key every 10,000 packets to insure much greater security than the standard WEP security. AES (Advanced Encryption Standard) is used to ensure the highest degree of security and authenticity for digital information. Pre‐Shared Key: This is used to identify each other in the network. Enter the name in the box, and this name must match the Pre‐ shared key value in the remote device. - 31 -...
Page 33
Network >> Wireless >> WPS Setting WPS (Wi‐Fi Protected Setup) sets a new standard of Wi‐Fi security, providing a simplified secure network setup solution for the end users. WPS can be enabled by the following two options: 1. PIN Mode 2. PBC Mode (or WPS button on the device, depending on hardware design) PROTECTED SETUP Press the Reset To Unconfigured button to reset the WPS configuration of the camera. WPS - PIN Mode: The PIN (Personal Information Number) mode builds the connection by entering the PIN Code directly. a. Click the PIN Mode option. b. Click Site Survey button to select the router (or access point) you want to connect. c. Click the Connect button to start WPS function of the camera. d. You need to enter the PIN Code displayed on the camera to the router (or access point) within 120 seconds to complete the setup. - 32 -...
Page 34
- PBC Mode: The PBC (Push‐Button‐Configuration) mode builds the connection by simply pressing a button on the device. a. Click the PBC Mode option. b. Click the Connect button to start WPS function of the camera. TIP Instead of clicking the Connect button of Configuration Utility, you can press the WPS button if the camera is designed with a hardware button of WPS function. c. You need to press the WPS button on the router (or access point) within 120 seconds to complete the setup. Device Status Display the WPS configuration of the camera. TIP The Power LED indicates the WPS connection status by: - blinking 3 times when the connection is built successfully. - repeating 3 times of short‐short‐long blink when the connection is failed. - 33 -...
4.5 Setting up Video & Audio The Video & Audio menu contains three sub‐menus that provide the video and audio settings for the camera. - 34 -...
Page 36
Video & Audio >> Camera Image Setting - Brightness: Adjust the brightness level from 0 ~ 100. - Contrast: Adjust the contrast level from 0 ~ 100. - Saturation: Adjust the colors level from 0 ~ 100 Click Default to restore the default settings of the three options above. - Mirror: Select the Horizontal option to mirror the image horizontally. Select the Vertical option to mirror the image vertically. - Light Frequency: Select the proper frequency according to the camera’s location: 50Hz, 60Hz, or Outdoor. Overlay Setting - Includes Date & Time: Select this option to display the date & time stamp on the live view image. - Enable Opaque: Select this option to set a black background to the displayed date & time stamp. - 35 -...
Page 37
Video & Audio >> Video MPEG4 - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Normal, High, and Highest. - Frame Rate: Select Auto or a proper setting depending on your network status. MJPEG - Video Resolution: Select the desired video resolution from the three formats: VGA, QVGA and QQVGA. The higher setting (VGA) obtains better video quality while it uses more resource within your network. - Video Quality: Select the desired image quality from five levels: Lowest, Low, Normal, High, and Highest. - Frame Rate: Select Auto or a proper setting depending on your network status. NOTE The camera supports both MPEG4 and MJPEG compression. MJPEG capture the images in JPEG format, which require higher bandwidth to view smooth video. The administrator can control the bandwidth of each connection well through the setting options above. 3GPP The camera supports 3GPP specification. Select the Disable option to disable this feature. Otherwise, select 3GPP Without Audio or 3GPP With Audio to transfer the video clips without or with audio. - 36 -...
Page 38
If you use a mobile phone that supports 3GPP, you can also view the real‐time streaming image captured by the camera on your phone (with the default player on the phone) by entering the RTSP link: rtsp://(IP address of the camera)/3gp. Video & Audio >> Audio Camera Microphone In Select the Enable option to enable the camera’s audio function, so that you can receive the on‐site sound and voice from the camera. Camera Speaker Out This option is displayed when you connect a 2‐way audio camera. Select the Enable option to enable the camera’s external speaker function, so that the connected speaker can play the sound and voice through the camera. - Volume: Set the speaker’s volume. - 37 -...
4.6 Event Server Configuration The Event Server menu contains three sub‐menus that allow you to get notification via HTTP when motion triggered, upload images to FTP, send emails that include still images, and store the images to a NAS system. When you complete the required settings for FTP, Email, or Network Storage, click Test to test the related configuration is correct or not. Once the camera connects to the server successfully, click Apply. Event Server Setting>> HTTP HTTP Notify for Motion Trigger Send the query parameter via an HTTP notification when an event is triggered. - Host Address: Enter the IP of the HTTP server - Port Number: Enter the Port number of the HTTP server - User Name: Enter the username of the HTTP server - Password: Enter the password of the HTTP server - Query: query address for the HTTP server - 38 -...
Page 40
Event Server Setting>> FTP FTP - Host Address: Enter the IP address of the target FTP server. - Port Number: Enter the port number used for the FTP server. - User Name: Enter the user name to login into the FTP server. - Password: Enter the password to login into the FTP server. - Directory Path: Enter the destination folder for uploading the images. For example, Camera1. - Passive Mode: Select the Enable option to enable passive mode. Event Server Setting >> Email Email - SMTP Server Address: Enter the mail server address. For example, mymail.com. - Port number: Assign the SMTP port in the text box. The default SMTP port is 25. - Encryption connection: Select SSL or STARTTLS if your email account uses this type of authentication. (Eg: gmail account) Leave both unchecked if you use regular SMTP email account. - Sender Email Address: Enter the email address of the user who will send the email. For example, John@mymail.com. - Authentication Mode: Select None or SMTP according to the mail server configuration. - Sender User Name: Enter the user name to login the mail server. - Sender Password: Enter the password to login the mail server. - Receiver #1 Email Address: Enter the first email address of the user who will receive the email. ...
Page 41
- Receiver #2 Email Address: Enter the second email address of the user who will receive the email. Event Server Setting >> Network Storage Net Storage - Samba Server Address: Enter the IP address of the Network Storage server. - Share: Assign the folder on the Network Storage server to share the files to users. For example, CameraRecord - Path: Assign a folder for this camera to upload the files on the Network Storage server. For example, TVIP312WN. Your files will be saved to NetworkStorage /CameraRecord/TVIP312WN folder - User Name: Enter the user name to login into the Network Storage server. (Check Anonymous if no ID/password required) - Password: Enter the password to login into the Network Storage server. - Split By: When the file is too large to upload smoothly, use this option to split it by selecting File Size or Recording Time. - When Disk Full: Select Stop Recording or Recycle – Delete Oldest Folder of File when the storage space on the Network Storage server is full. NOTE The video recorded files in Network Storage are enclosed by AVI format without Audio. - 40 -...
4.7 Motion Detect The Motion Detect menu contains the command and option that allow you to enable and set up the motion detection feature of the camera. The camera provides two detecting areas. To enable the detecting area, select Window 1 or 2 from the pull‐down list, and then select Enable. When the detecting area is enabled, you can use the mouse to move the detecting area and change the area coverage. - Name: Assign a name to the detecting area. - Threshold: Move the slide bar to adjust the level for detecting motion to record video. - 41 -...
4.8 Event Config The Event Config menu contains four sub‐menus that provide the commands to configure event profiles. Event Configuration >> General Setting - Snapshot/Recording Filename Prefix: You can assign a given prefix to each new captured file. Otherwise, leave this option blank to use the default setting. - Network Storage Recording Time Per Even: Limit the recording time while you are using the Network Storage solution. - 42 -...
Page 44
Event Configuration >> Arrange Schedule Profile This sub‐menu displays the scheduled profile(s). To customize the profile, click Add and then enter a descriptive name for the profile in the prompt dialog window. After entering the profile name, click OK and the profile is added to the Schedule Profiles list. To delete the profile, select the profile in the list and click Delete. - Profile Name: Display the profile name that you select in the Schedule Profiles list. - Weekdays: Select the weekday(s) that you want to separately assign in the schedule profile. The weekday that has been assigned will be displayed with green color. - 43 -...
Page 45
- Time List: Display the time period that you have assigned within the selected weekday. To assign the same time period to every weekday, click Add this to all weekdays; click Delete this from all weekdays to remove the selected time period from every weekday. Click Delete to remove the selected time period. - Start/End Time: Enter the start and end time and then click Add to assign a time period within in the selected weekday. Event Configuration >> Motion Detect Trigger Select the Enable option to enable the trigger function of the camera, so that you can send captured images within the detecting area to the FTP server, email receiver, Network Storage server, or the connected USB device. You have to configure corresponding settings, such as FTP server and email server, to enable this feature. - Schedule Profile: Select a schedule profile from the pull‐down list. - Action: Select the destination that the captured images will be sent to: Send Email, FTP Upload, Record to Network Storage, or Save Image to USB. - 44 -...
Page 46
Event Configuration >> Schedule Trigger You can separately configure the schedule for trigger function of the camera by Email, FTP, or Network Storage. Select the Enable option on each item, and then select a Schedule Profile from the pull‐down list and set the Interval time. NOTE If the setting value of the Network Storage Recording Time Per Event option in General Setting is longer than the Interval time in Network Storage Schedule, the recorded file will be a continuous video clip. For example, if you set the Network Storage Recording Time Per Event as 10 seconds and the Interval as 5 seconds, recorded file becomes a non‐stop video clip because the camera will record a 10‐second video clip every 5 seconds. - 45 -...
4.9 Tools The Tools menu provides the commands that allow you to restart or reset the camera. You can also backup and restore your configuration, and upgrade the firmware for the camera. - 46 -...
Page 48
Factory Reset Click Reset to restore all factory default settings for the camera. System Reboot Click Reboot to restart the camera just like turning the device off and on. The camera configuration will be retained after rebooting. Configuration You can save your camera configuration as a backup file on your computer. Whenever you want to resume the original settings, you can restore them by retrieving the backup file. - Backup: Click Get the backup file to save the current configuration of the camera. - Restore: Click Browse to locate the backup file and then click Restore. Update Firmware This item displays the current firmware version. You can upgrade the firmware for your camera once you obtained a latest version of firmware. - Select the firmware: Click Browse to locate the backup file and then click Update. NOTE Make sure to keep the camera connected to the power source during the process of upgrading firmware. Otherwise, the camera might be damaged because of failure of upgrading firmware. - 47 -...
4.10 USB The USB menu provides the information and controls of the connected USB device. USB Dismount To safely remove the connected USB device, you can press the Unmount button for four seconds on the camera or click Dismount from this item. USB Information Display the Total space and Free space of the USB device. - 48 -...
Page 50
USB Setting - When Disk Full: Select Stop Recording or Recycle – Delete Oldest Folder of File when the storage space on the USB device is full. NOTE The connected USB storage device can be only used to store still images. - 49 -...
4.11 Device Info The Information menu displays the current configuration and events log of the camera. - 50 -...
Page 52
Device Info Display the Basic, Video & Audio, Network, and Wireless settings of the camera. System Log The Logs table displays the events log recorded by the system. - 51 -...
5 HAPTER ™ ECUR RO OFTWARE This chapter describes detailed instructions on using SecurView Pro, a customized software application with a user‐friendly interface that allows you to access your cameras. The Software can monitor and record up to 36 cameras. It also let you change some basic settings of the camera, such as schedule profiles and motion detecting areas. The SecurView Pro also supports audio or Pan/Tilt function. It is recommended to use a high performance computer if you want to connect multiple cameras simultaneously. Platform: Microsoft® Windows® 7/Vista/XP Hard Disk: 80GB or above Resolution: 1024x768 or above Hardware Requirement The following provides the minimum hardware requirements: 1 ~ 8 cameras: Intel Core 2 Duo; 2GB RAM 9 ~ 32 cameras: Intel Core 2 Quad; 4GB RAM * For Windows Vista users: please go to User Accounts and Family Safety > User Accounts > Turn User Account Control on or off, then uncheck the checkbox of “Use User Account Control (UAC) to help protect your computer”. Restart your computer to validate the setting. For additional information of User Account Control, please go to http://www.microsoft.com/windows/products/windowsvista/features/d etails/useraccountcontrol.mspx - 52 -...
5.1 Installation 1. Insert the Installation CD‐ROM into your computer’s CD‐ROM drive to initiate the Auto‐Run program. 2. Click the SecurView Pro from the Auto‐Run menu screen. NOTE: To use SecurView™ Pro, you must have Microsoft .NET Framework 2.0 installed in the computer. The setup wizard will detect it and, if the program is not installed yet, it will ask you to install it during the process of installing SecurView™ Pro. NOTE: Microsoft Windows Installer 3.0 or above is a required component ...
Page 55
3. Then SecurView Pro Setup Wizard will appear. Click “Install”. 4. Wait until the program finish the installation. By default, the destination location is C:\Program Files\TRENDnet\SecurView Pro. - 54 -...
Page 56
5. Click “Finish” to finish the installation. 6. After installing the SecurView Pro, the application is automatically installed to your computer, and creates a folder in “ Start \Program\TRENDnet\SecurView Pro ”. - 55 -...
5.2 Using SecurView™ Pro 5.2.1 Launch the Program To start SecurView Pro, click Start > All Programs > TRENDnet >SecurView Pro > SecurView Pro. You can also start the program by double‐click the SecurView Pro icon on your desktop. On the login window, enter the User name/Password and click OK to login. The default User name/Password is admin/admin. If you wish to save the login information, please select Auto Login. - 56 -...
Page 58
5.2.2 Main Window and Features When you start and login to SecurView Pro, the Main window will display as below: The Main window provides you with the information on operating the system, as well as the control panel such as the Quick Launch buttons, and so on. NOTE For best result, it is higher recommended to configure resolution setting to 1024 x 768 or higher; otherwise, it cannot be displayed on the screen when launching the program. Live View Window displays the live video of the connected camera(s). - 57 -...
Page 59
Quick Launch Buttons are located below the Live View Window, providing you with the following quick‐launch functions: Button Function Logout : To log out the SecurView Pro program Close: To close the SecurView Pro program Restore Recording Type: Restore all recording type to current camera’s setting All Continuous Recording: Continuous recording on all cameras Stop All Recording: Stop recording on all cameras View Setting: To configure eMap settings eMap View: To view current maps Camera Status: Display cameras status Playback: Playback recorded files Schedule: Display Schedule Configuration window Event Server: Setup a SMTP server Address Book: Add/Remove email address for event notification Event Trigger: Setup event trigger configuration Device Setting : Set up the camera Recording Setting: Set up the recording path Account information: Setup administrator password Version: Display software version ...
Page 60
Camera View Mode buttons in this area allow you to switch the camera view mode. Buttons Functions Display the connected camera(s) in a single camera view mode. Display the connected camera(s) in a quad view mode. Display the connected camera(s) in a 3 x 3 grid view mode. Display the connected camera(s) in a 13‐camera view mode using a split window. The first camera is displayed as the major view. Display the connected camera(s) in a 17‐camera view mode using a split window. The first camera is displayed as the major view. Display the connected camera(s) in a N x N grid view mode, supporting up to 36 cameras. Display the live view of the selected camera in full screen mode. Click ESC on the keyboard to return to Main window. Automatically switch the live view of each connected cameras in single camera view mode by 30 seconds*. Click once to start and click again to stop. * The auto‐switch time is set as 30 seconds by default, which can be changed by clicking the System Setting and ...
Page 61
Camera List displays the status of the connected cameras. If multiple cameras are connected, you can switch to the live view of each camera by simply selecting the camera from the list. eMap allows you to select the desired camera to the view from the map easily. Please note that you have to set up the eMap for monitoring in advance. Camera Control Buttons provides the control buttons that allow you to control the selected camera. Buttons Functions Talk On/Off. Click to enable/disable the speaker function of the connected camera. This option is available only in single camera view mode. Listen On/Off. Click to enable/disable the microphone function of the connected camera. This option is available only in single camera view mode. For Pan/Tilt cameras, use this control panel to set the preset positions (up to 8 positions). Use Navigation buttons to adjust camera position, and then select the position number (1~8) from the Set button. To move to the preset position, simply select the position number (1~8) from the Go button. Navigation Buttons (Left/Right/Up/Down/Home). If the connected camera has pan/tilt functions, the Navigation buttons allow you to move the camera lens position. Clicking the Home (center) button will move the camera lens to the assigned home position. The Patrol/Stop buttons are used to enable/disable the patrol function of the camera. Click Patrol to start / patrolling through the preset positions once. Click Stop to ...
Page 62
5.2.3 Manage the Cameras Before adding the cameras, please setup the recording setting first. Configure Recording Settings 1. Click the button and then select Record Setting. 2. Default path is C:\, click Browse and select the desire directory then click Save to complete the configuration. To change the time interval for recording, select time from the pull‐down menu. NOTE: The system will automatically delete the oldest files (10%) when the size of recorded files is up to 90% of the storage space. - 61 -...
Page 63
Add a Camera 1. Click the button and select Device Setting to display the Device Setting window. 2. Click New. - 62 -...
Page 64
3. Click on Device Search, all cameras that’s connected to your network would appear. 4. Select the camera you would like to add and then click Add. - 63 -...
Page 65
5. The information of the camera will display on the screen. It will auto detect the IP address/port number and display the stream type of the camera. Please type in the correct user name and password, then select Preview to view live image. 6. To setup recording style, select Yes on Record option. These four recording types will appear. Select one of the recording type, configure it then click Save. Continuously: Record the stream video continuously - 64 -...
Page 66
Schedule: Records stream video by schedule. You can setup the schedule by click Add Schedule here. Click on New to create a new schedule and select the time to record. Click on Save when finish. Motion: Record video by Motion Detection. Motion detection recording required to setup a motion detection area. If you are adding a new camera, you must save the camera information first before setup the motion detection area. - 65 -...
Page 67
To use motion detection record, please enable the detection areas first. Click on Motion detection area to setup Enable motion detection windows, set up the senstivity and click on Save. - 66 -...
Page 68
Motion by Schedule: same requirement as Motion & Schedule recording. Digital Input: Recording triggered when there I/O port is triggered.After all recording methods are configured, click Save to apply the settings. 7. Camera list will appear with recording type notification. - 67 -...
Page 69
8. Once you added all the cameras, click the close button “x” on the Device Setting windows to return to the main windows. The cameras will display here. NOTE Divx/Xvid codec is required for viewing the image of camera. If the image cannot be displayed in the Live View/Preview window normally, click the following path to download and install the required component: http://download.divx.com/divx/DivXInstaller.exe - 68 -...
Page 70
Edit / Delete a Camera 1. To edit a camera: From the Device Setting window, highlight the camera you would like to edit then click on Modify button. 2. To delete a camera: select the desired one and then click Remove. Click Yes to confirm. - 69 -...
Page 71
View Camera Image Since you have added camera(s) to the system, the image of the selected camera(s) will be displayed on the Live View Window automatically. You can view a maximum of 36 cameras simultaneously. Additionally, you can select one‐camera or other view mode to display the video from the Camera View Mode buttons. For example, if you use only one camera, select single camera view mode ( ), and the Live View Window will display the view as below. You can select the other modes according to your need. The Information icon ( ) on the top‐right corner of the window provides you with the options to connect/disconnect the camera, select a camera to be displayed in the window, capture a still image of the camera live video, or switch to eMap mode. Click the Information icon to pop up the shortcut menu and select the desired option. - 70 -...
Page 72
Playback the Recorded Files 1. Click the button to display the Playback window. 2. On the Playback window, select the camera and setup the begin/end date and begin/end time, then click Search. The search result will be displayed in the Record File list. - 71 -...
Page 73
3. To playback the video clip, select the desired file and click Play. - 72 -...
Page 74
5.2.4 eMap Setup & Camera Status Manage eMap Click the button and select View Setting to manage eMap. eMap refers to the geography and device scope in the SecurView Pro, which visually presents the devices in your security system. It uses a background of the area (e.g. a picture or a map) as the interface for monitoring. To add an eMap 1. On the View Setting window, click New. - 73 -...
Page 75
2. Enter an eMap name. 3. Click Browse to select a Picture File from your computer. Picture will display in the Preview window. - 74 -...
Page 76
4. Click Save and click OK to apply the settings. 5. Click Camera Location to assign the camera location. - 75 -...
Page 77
6. The following screen appears. 7. Select the camera from the list and then click the position on the map. The camera icon will be displayed on map. - 76 -...
Page 78
8. Click Save when complete. To modify/remove an eMap 1. To edit the eMap: In the eMap List, select the map name from eMap list, and click Modify. The map’s information will display on the preview windows. After changes the setting information, click Save to save the setting. - 77 -...
Page 79
To delete the eMap: In the eMap List, select the desired one and click Remove. The selected map will be removed from the list. View eMap Click the button and select eMap View. - 78 -...
Page 80
b. Select the map from the eMap Name list. Camera Status Click the camera icon , the camera Live Monitor window will display live image on that camera. - 79 -...
Page 81
5.2.5 System Info Account Click the System button and select Account to change the administrator password of the system. Enter the Current password, and then enter the new password twice (in the Type new password and Retype password boxes). Then click Save. - 80 -...
Page 82
Version Click the System button and select Version to view the current firmware version of the system. System Setting Click the System button and select System Setting. Auto Scan period can be set from 30 seconds to 100 seconds. - 81 -...
Page 83
5.2.6 Event Settings Setting up Event Server Click the button and select Event Server to configure the SMTP settings for email notification use. - 82 -...
Page 84
Select the Enable SMTP option and configure the following information correctly to start the email feature. SMTP Server Address: Enter the mail server address. For example, mymail.com or smtp.gmail.com or smtp.live.com Sender Email Address: Enter the email address of the user who will send the email. For example, John@mailserver.com. Authentication Mode: Select None or SMTP according to the mail server configuration. Sender User Name: Enter the user name to login the mail server. Sender Password: Enter the password to login the mail server. Port Number: Enter the port number used for the email server. SSL: If the mail server requires an encrypted connection, you should check the SSL option. For example, gmail users, please select this option. When completed, click Save and then select OK. The system will automatically start the Event Service. TIP The status of Event Service is indicated by the icon in the system bar. - 83 -...
Page 85
Sending Notification to the User Click the button and select Address Book to assign the user to the Address Book of the camera. The user will receive a real‐time notification from the system while triggering out. 1. On the Address Book window, click New. 2. In the Address Book Information field, enter the Name and Email of the user. 3. When completed, click Save. The user will be displayed in the Address Book List. - 84 -...
Page 86
4. To edit the user: In the Address Book List, select the desired user and click Modify. The user’s information will be displayed, where you can change the user’s information and then click Save when completed. 5. To delete the user: In the Address Book List, select the desired user and click Remove. The selected user will be removed from the list. Configuring Event Trigger Click the button and select Event Trigger to configure the trigger out function of the camera. - 85 -...
Page 87
1. On the Event Trigger window, select the desired camera from the Camera List. 2. Do one of the following: SMTP: Select this option and enter the Subject and Message, the system will send an email message to the selected user(s) in the Address Book List. Play Sound: Select this option select a sound file from the computer, so that the system will alarm by the sound while triggering out. eMap Popup: Select this option and select the eMap profile from the pull‐down menu. The camera view of the eMap will be displayed while triggering out. 5.2.7 Close Program When you have finished operating, click the button and select Logout to logout the system or Close to exit the program. - 86 -...
6 HAPTER How to access the camera behind a Router You can either setup the Dynamic DNS connection via camera itself or your home router. An account from any of the listed DDNS providers is required prior to this operation. 6.1 Configure DDNS on your Camera 1. Go to Camera’s DDNS Setting page, click Enable to activate the feature. Then select a DDNS provider from the list. 2. Enter your DDNS’s the Host Name, User Name and Password. - 87 -...
Page 89
3. In the Port Number section, assign an HTTP port of the camera. The default HTTP Port on the camera is 80. The example shows above is using port number 9000. 4. Open another web browser and go to your Router’s Web Configuration page. (In the example, TRENDnet’s TEW‐651BR Wireless N router is used) 5. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. CameraName) Protocol: Select TCP - 88 -...
Page 90
Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. Then click Add to add the application. * Please refer to your router’s user’s manual for detail Virtual Server setting. Some router might use Port Forwarding or Special applications for this function. The setup steps should be very similar. - 89 -...
Page 91
6. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber 7. Camera’s login page will appear. 6.2 Configure DDNS on your router 1. Go to Camera’s DDNS Ports Number section, assign a HTTP port for your camera and click Apply. 2. Login to your router’s web configuration page. - 90 -...
Page 92
3. Find the Dynamic DNS configuration section. 4. Enable DDNS, fill out the following information and then click Apply. - 91 -...
Page 93
8. Go to Virtual Server* section and create a new entry. Enable: Click Enable Name: Enter the application name (eg. CameraName) Protocol: Select TCP Private Port: The HTTP port that you assign on your Camera. Public Port: The port used on remote side to access to your Camera. LAN Server: The local IP address of your Camera. Click Add to add the application. * Please refer to your router’s user’s manual for detail Virtual Server setting. Some router might use Port Forwarding or Special applications for this function. The setup steps should be very similar. 9. Open another web browser and enter your DDNS domain and camera’s port number. http://yourDomainName:PortNumber 10. The camera login page will appear. - 92 -...
PPENDIX A.1 Specification Camera General Sensor: 1/4” color CMOS sensor Resolution: 640 x 480 pixels Board Lens Focal Length: 4.5mm Aperture (F/No): F2.8 IR LED with light sensor control Minimum illumination: 0 Lux Diagonal viewing angle: 60 degree Image & Compression: MPEG‐4/MJPEG dual streaming Video Exposure/white balance/gain control : automatic Resolution: up to 30fps for VGA (640x480), 30fps for QVGA (320x240), 30fps for QQVGA (160x120) Audio Audio in: internal omni‐directional microphone Sensitivity: ‐48dB +/‐ 3dB Frequency response: 50 ~ 16000Hz Audio out: external output to active speaker (mono) Echo Cancellation: hardware voice processor Audio codec: PCM/AMR Hardware Network IEEE 802.3u 10/100Mbps Fast Ethernet, Auto‐MDIX LED Power, Link USB Port Type A USB 1.1 host port Reset Button Restore to factory default WPS Button Push button for Wi‐Fi Protected Setup Power 8 watts max. Consumption - 93 -...
Page 95
Power 5 V, 2.5 A external power adapter Dimension 70 x 100 x 57 mm (2.67 x 3.94 x 2.95 in.) Weight 155 g (5.4 oz) Temperature Operating: 0°C ~ 45°C (32°F ~ 113°F) Storage: ‐15°C ~ 60°C (5°F ~ 140°F) Humidity Max. 90% (non‐condensing) Certifications CE, FCC Requirement Management Internet Explorer 6.0 or above Interface To Run Windows 7 (32/64 bit), Vista (32/64 bit), XP (32/64 bit) SecurView Pro SecurView Channel: supports up to 32 cameras Pro Record/Playback/Motion Detection Network TCP/IP, UDP, ICMP, DHCP, NTP, DNS, DDNS, SMTP, FTP, Protocols HTTP, Samba, PPPoE and UPnP Wireless Standard Based on IEEE 802.11n technology IEEE 802.11g/b compliant Frequency 2.4 ~ 2.4835GHz Antenna 1 x 2dBi dipole antenna (Reverse‐SMA connector) Data Rate 802.11n: up to 150Mbps (auto ...
Page 96
Receiving 802.11n HT20: ‐67dBm Sensitivity 802.11n HT40: ‐64dBm 802.11g: ‐70dBm 802.11b: ‐87dBm Channel 1~11 (FCC), 1~13 (ETSI) Management Remote Remote management supported Backup / Save/retrieve configuration files Restore Settings Image Brightness, sharpness, saturation, flip, mirror (horizontal/vertical) Video Encoding type: Resolution: 640 x 480, 320 x 240, 160 x 120 Frame rate: 1~ 30 fps Compression: 5 levels Recording Recording type: continuous, schedule or motion detection with software Multi‐Profile 3 profiles simultaneously Port Settings HTTP port: 80 (default) Digital Zoom 3x Dynamic DNS Yes Time Synchronize with NTP server or set time/date manually SMTP SMTP mail supported up to 2 accounts with software System Log 100 entries (max.) - 95 -...
A.2 Glossary of Terms NUMBERS 10BASE-T is Ethernet over UTP Category III, IV, or V 10BASE-T unshielded twisted-pair media. The two-pair twisted-media implementation of 100BASE-T is 100BASE-TX called 100BASE-TX. Adaptive Differential Pulse Code Modulation, a new ADPCM technology improved from PCM, which encodes analog sounds to digital form.
Page 98
Communication has four components: sender, receiver, Communication message, and medium. In networks, devices and application tasks and processes communicate messages to each other over media. They represent the sender and receivers. The data they send is the message. The cabling or transmission method they use is the medium.
Page 99
An enterprise network consists of collections of networks Enterprise connected to each other over a geographically dispersed network area. The enterprise network serves the needs of a widely distributed company and operates the company’s mission- critical applications. The most popular LAN communication technology. There Ethernet are a variety of types of Ethernet, including 10Mbps (traditional Ethernet), 100Mbps (Fast Ethernet), and...
Page 100
Short for hexadecimal refers to the base-16 number system, which consists of 16 unique symbols: the numbers 0 to 9 and the letters A to F. For example, the decimal number 15 is represented as F in the hexadecimal numbering system. The hexadecimal system is useful because it can represent every byte (8 bits) as two consecutive hexadecimal digits.
Page 101
that IP address. ISP (Internet Service Provider) is a company that maintains a network that is linked to the Internet by way of a dedicated communication line. An ISP offers the use of its dedicated communication lines to companies or individuals who can’t afford the high monthly cost for a direct connection.
Page 102
network appear to the Internet as a single address. For routing messages properly within your network, each device requires a unique IP address. But the addresses may not be valid outside your network. NAT solves the problem. When devices within your network request information from the Internet, the requests are forwarded to the Internet under the router's IP address.
Page 103
use to communicate with each other, and thus they have different functions. Some protocols are responsible for formatting and presenting and presenting data that will be transferred from file server memory to the file server’s net work adapter Others are responsible for filtering information between networks and forwarding data to its destination.
Page 104
It is a simple computer that provides resources, such as files Server or other information. SIP (Session Initiated Protocol) is a standard protocol that delivers the real-time communication for Voice over IP (VoIP), which establishes sessions for features such as audio and video conferencing.
Page 105
that resides above IP in the TCP/IP suite The USERNAME is the unique name assigned to each person User Name who has access to the LAN. It is a program that performs a specific task. Utility Unshielded twisted-pair. UTP is a form of cable used by all access methods.
Page 106
Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TV‐IP312WN – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable ...
Page 107
TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA ...
Page 108
OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF ...
Page 109
Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each ...