TRENDnet TV-IP312 Quick Installation Manual
Hide thumbs
Also See for TV-IP312:
- Quick installation manual (11 pages) ,
- Specifications (3 pages) ,
- User manual (116 pages)
Related Manuals for TRENDnet TV-IP312
Summary of Contents for TRENDnet TV-IP312
- Page 1 Quick Installation Guide TV-IP212/TV-IP212W TV-IP312/TV-IP312W H/W: A1.0R...
-
Page 2: Table Of Contents
Table of Contents Table of Contents English ...................... 1 1. Before You Start ................2. Hardware Installation ................ Configure the Internet Camera Server ..........Troubleshooting ..................Version 02.17.2009... -
Page 3: English
1. Before You Start Package Contents TV-IP212/TV-IP212W/TV-IP312/ TV-IP312W Utility CD-ROM Quick Installation Guide 1 x 2dBi Detachable Antenna TV-IP212W/TV-IP312W only) AC Power Adapter (5V, 2.5A) System Requirements 10/100Mbps Ethernet CPU: 1GHz processor or above Memory: 256MB RAM or above/ 512MB RAM or above (Windows Vista) VGA resolution: 800 x 600 or above Web Brower: Internet Explorer (5.0 or higher) Wireless access point or wireless router for TV-IP212W/TV-IP312W... -
Page 4: Hardware Installation
2. Hardware Installation 1. Attach the Antenna. (TV-IP212W/TV-IP312W only) 2. Connect a RJ-45 network cable from a Switch/Router to the Ethernet port of the Internet Camera server. 3. Connect external speaker to the Internet Camera Server (optional) 4. Connect the AC Power Adapter to the Internet Camera Server and then to a power outlet. -
Page 5: Configure The Internet Camera Server
1. Insert the Utility CD-ROM into your CD-ROM drive and then click IP Setup. 2. Follow the IPSetup Setup Wizard instructions and then click Next. 3. Click Close. 4. Go to Start -> Programs -> TRENDnet -> IPSetup and click IPSetup. English... - Page 6 5. Select the camera server and click Change IP. 6. Configure the IP address to be in the same subnet as your network, type in the Administrator ID and Password and click Change. By default: admin Password: admin 7. Click OK and wait 30 seconds. 8.
- Page 7 10. Enter the User name and Password, and then click OK. By default: User Name: admin Password: admin 11. Right click and select Install Active X Control. 12. Click Install. 13. Click Setup, Network and then click Wireless. Configure your wireless settings to match your wireless network's settings and then click Apply (Enable/Enter...
- Page 8 For detailed information regarding the TV-IP212/TV-IP212W/TV-IP312/ TV-IP312W configuration and advanced settings, please refer to the User's Guide included on the Utility & Driver CD-ROM or TRENDnet's website at www.trendnet.com Register Your Product To ensure the highest level of customer service and support, please take a moment to www.trendnet.com/register...
-
Page 9: Troubleshooting
Enable option is checked. Third, make sure to disconnect the Ethernet cable from the camera and verify that the LINK LED is blinking green. If you still encounter problems or have any questions regarding the TV-IP212/TV-IP212W/ TV-IP312/TV-IP312W, please contact TRENDnet’s Technical Support Department. - Page 10 Certifications This equipment has been tested and found to comply with FCC and CE Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received. Including interference that may cause undesired operation.
- Page 11 Product Warranty Registration Please take a moment to register your product online. Go to TRENDnet’s website at http://www.trendnet.com/register 20675 Manhattan Place Torrance, CA 90501 Copyright ©2009. All Rights Reserved. TRENDnet.