Onkyo TX-NR1010 Instruction Manual page 98

If the input signal format is set to "PCM" or "DTS".
Set it to "Off".
■
Only the front speakers produce sound
When the Stereo or Mono listening mode is selected,
only the front speakers and subwoofer produce
sound.
In the Mono listening mode, only the front speakers
output sound if the "Output Speaker" setting is set
to "Left / Right".
Check the Speaker Configuration.
■
Only the center speaker produces sound
If you use the Dolby Pro Logic IIx Movie, Dolby Pro
Logic IIx Music, or Dolby Pro Logic IIx Game
listening mode with a mono source, such as an AM
radio station or mono TV program, the sound is
concentrated in the center speaker.
In the Mono listening mode, only the center speaker
output sound if the "Output Speaker" setting is set
to "Center".
Make sure the speakers are configured correctly.
■
The surround speakers produce no sound
When the T-D (Theater-Dimensional), Stereo or
Mono listening mode is selected, the surround
speakers produce no sound.
Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
Make sure the speakers are configured correctly.
When Powered Zone 3 is used, playback in the main
room is reduced to 3.2 channels and the surround
speakers produce no sound.
■
The center speaker produces no sound
When the Stereo or Mono listening mode is selected,
the center speaker produces no sound.
In the Mono listening mode, only the front speakers
output sound if the "Output Speaker" setting is set
to "Left / Right".
77 Make sure the speakers are configured correctly.
■
The front high, front wide and surround back
speakers produce no sound
46
Depending on the current listening mode, no sound
may be produced by the front high, front wide and
surround back speakers. Select another listening
mode.
69
Depending on the sources, the sound produced by the
front high, front wide and surround back speakers
may be weak.
64
Make sure the speakers are configured correctly.
When Powered Zone 2 is used, playback in the main
room is reduced to 5.2 channels and the front high,
—
front wide and surround back speakers produce no
sound.
When Powered Zone 3 is used, playback in the main
room is reduced to 3.2 channels and the front high,
front wide and surround back speakers produce no
69
sound.
■
The subwoofer produces no sound
64
When you play source material that contains no
information in the LFE channel, the subwoofer
produces no sound.
—
Make sure the speakers are configured correctly.
■
There's no sound with a certain signal format
42
Check the digital audio output setting on the
connected device. On some game consoles, such as
those that support DVD, the default setting is off.
64
With some DVD-Video discs, you need to select an
—
audio output format from a menu.
Depending on the input signal, some listening modes
cannot be selected.
■
Can't select the Pure Audio listening mode
—
The Pure Audio listening mode cannot be selected
while Zone 2/3 is on.
69
En-98
■
Can't get 6.2/7.2 playback
64
If no surround back speakers, front wide and front
high speakers are connected, or the Zone 2/3 speakers
are being used, 6.2/7.2 playback is not possible.
Depending on the number of connected speakers, it is
42
not always possible to select all of the listening
modes.
■
The speaker volume cannot be set as required
—
Check to see if a maximum volume has been set.
If the volume level of each individual speaker has
64
been adjusted to high positive values, then the
— maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after the Audyssey MultEQ
Room Correction and Speaker Setup has been
performed.
—
■
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and the like may degrade the
audio performance, so refrain from doing it.
An audio cable may be picking up interference. Try
—
repositioning your cables.
■
The Late Night function doesn't work
64
Make sure the source material is Dolby Digital,
Dolby Digital Plus, and Dolby TrueHD.
— Make sure that the "TrueHD Loudness
Management" setting is not set to "Off". The Late
Night function doesn't work when this setting is
disabled.
—
42-49
—
Appendix
—
42-49
78
39, 66
® XT32
—
—
56
69