Onkyo TX-NR1010 Instruction Manual
  1. Manuals
  2. Brands
  3. Onkyo Manuals
  4. Receiver
  5. TX-NR1010
  6. Instruction manual

Onkyo TX-NR1010 Instruction Manual

Owner manual
Hide thumbs Also See for TX-NR1010:
Table of Contents

Advertisement

Quick Links

Enlarged version
AV RECEIVER
TX-NR1010
Instruction Manual
Contents
Safety Information and Introduction ............2
Table of Contents ...........................................6
Connections .................................................13
Turning On & Basic Operations..................23
Advanced Operations ..................................54
Controlling Other Components...................88
Appendix .......................................................97
Internet Radio Guide
Remote Control Codes
E
n

Advertisement

Table of Contents
loading

Related Manuals for Onkyo TX-NR1010

Summary of Contents for Onkyo TX-NR1010

  • Page 1 Contents AV RECEIVER Safety Information and Introduction ....2 TX-NR1010 Table of Contents ...........6 Connections ..........13 Turning On & Basic Operations....23 Instruction Manual Advanced Operations ........54 Controlling Other Components....88 Appendix ............97 Internet Radio Guide Remote Control Codes...

  • Page 2: Safety Information And Introduction

    Important Safety Instructions exposed to rain or moisture, does not operate normally, Leave 20 cm (8") of free space at the top and sides and 1. Read these instructions. or has been dropped. 10 cm (4") at the rear. The rear edge of the shelf or 2.

  • Page 3: Precautions

    • If you do not use this unit for a long time, it may not requirements printed on the unit’s rear panel (e.g., AC...
  • Page 4 MATCH WIDE BLADE OF PLUG TO WIDE SLOT, If the power cord’s plug is not suitable for your socket FULLY INSERT. outlets, cut it off and fit a suitable plug. Fit a suitable fuse Modèle pour les Canadien in the plug.

  • Page 5: Supplied Accessories

    • If the remote controller doesn’t work reliably, try replacing the batteries. • Don’t mix new and old batteries or different types of batteries. • If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

  • Page 6: Table Of Contents

    Remote Mode Setup ..........25 Setup Menu Items............. 59 Network Connection..........25 Input/Output Assign ..........60 To reset the AV receiver to its factory defaults, turn it Terminating the Initial Setup ........25 Speaker Setup ............63 on and, while holding down CBL/SAT, press Audio Adjust..............

  • Page 7: Features

    Safety Information and Introduction Features Connections Miscellaneous • 9 HDMI Inputs (1 on front panel) and 2 Outputs • 40 FM/AM Presets Amplifier • Zone 2 HDMI Output • Dolby Volume • Audyssey MultEQ ® XT32 to correct room acoustic •...

  • Page 8: Front & Rear Panels

    Safety Information and Introduction Front & Rear Panels Front Panel (North American models) (European models) En-8...
  • Page 9 DIMMER button (North American models) (51) g Input selector buttons (26) p MEMORY button (34) h Front flap Gently push on the lower end of the front panel to open q TUNING MODE button (34) the flap. r LISTENING MODE buttons (42)
  • Page 10 Safety Information and Introduction Display For detailed information, see the pages in parentheses. i Input indicators (109) a Speaker/channel indicators HDMI indicator (80) b Z2 (Zone 2) indicator (85) DIGITAL indicator ANALOG indicator c Z3 (Zone 3) indicator (85) j Bi AMP indicator...
  • Page 11 REMOTE CONTROL jack (FRONT L/R, CENTER, SURR L/R, p Composite video and analog audio jacks f HDMI IN and HDMI output (HDMI OUT MAIN and SURR BACK L/R, FRONT HIGH/ZONE 3 L/R and HDMI OUT SUB/ZONE 2) jacks...

  • Page 12: Remote Controller

    Receiver mode. RECEIVER). You can also use the remote controller to control Controlling the AV Receiver You can select AM or FM by pressing TUNER repeatedly. Onkyo Blu-ray Disc/DVD player, CD player, and a q/w buttons (34) other components. See “Entering Remote Control Codes” for more b D.TUN button (34)

  • Page 13: Connections

    7.2-channel playback The following illustration shows how to connect the speakers to each pair of terminals. If you’re using only one surround back speaker, connect it to the SURR BACK L terminals. Select the speakers (surround back, front high, front wide) you Connecting Your Speakers want to use for 7.2-channel playback.
  • Page 14 Then all sound will be out of phase and will sound unnatural. you need to do is to match the color of each label to the • Unnecessarily long, or very thin speaker cables may corresponding speaker terminal.
  • Page 15 The level and distance can be set individually for each output. If you’re using only one subwoofer, connect it to SW1 PRE OUT. • If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier. En-15...
  • Page 16 AV receiver is Note able to drive up to a 5.2 speaker system in the main room. • Specify “None” for any channel that you don’t want to output You must enable “Digital Crossover” in “Speakers (➔...

  • Page 17: About Av Connections

    • The AV receiver’s optical digital jacks have shutter-type covers Blu-ray Disc/ a display device (also called D-Sub or D-subminiature). that open when an optical plug is inserted and close when it’s DVD player Game console removed. Push plugs in all the way.

  • Page 18: Connecting Components With Hdmi

    Satellite/cable set-top box, etc. • In the case of Blu-ray Disc/DVD players, if no sound is output or the TV is set to another input source, this may result in no ✔ despite following the above-mentioned procedure, set your Blu- Set top box/digital video recorder, etc.

  • Page 19: Connecting Your Components

    See “Connection Tips and Video Signal Path” for more The on-screen menus appear only on a TV that is connected to HDMI OUT MAIN. If your TV is connected to other information (➔ page 107).
  • Page 20 Connections output from PC IN, select “- - - - -” for “PC” in the “HDMI No. Jack/Port Components Input” setting (➔ page 61). COMPONENT VIDEO • With connection D, you can enjoy Dolby Digital and MONITOR OUT TV, projector, etc.

  • Page 21: Connecting The Antennas

    Note • Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception. • Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

  • Page 22: Connecting Onkyo Ri Components

    System Off • Some components have two u jacks. You can connect either • Do not use a power cord other than the one supplied with the AV one to the AV receiver. The other jack is for connecting When you turn off the AV receiver, the components turn receiver.

  • Page 23: Turning On & Basic Operations

    Receiver Press 8ON/STANDBY on the front panel. To ensure smooth operation, here’s a few easy steps to help you configure the AV receiver before you use it for 8ON/STANDBY the very first time. These settings only need to be made Press RECEIVER followed by 8RECEIVER on the once.

  • Page 24: Initial Setup

    The automatic speaker setup is performed The on-screen menus appear only on a TV that is • Pressing HOME will close the setup wizard. To restart the initial following instructions on screen. Refer to step 2 connected to HDMI OUT MAIN.

  • Page 25: Source Connection

    Remote Mode Setup network checking. This step checks the connection of source components. With this step, you can enter remote control codes for the The checking is complete when the message components you want to operate. “Successfully connected.” appears at the middle of Use q/w to select one of the following options, and the screen.

  • Page 26: Playback

    • The time until the screen saver activates itself can be changed in the “Screen Saver” setting (➔ page 79). Listening mode buttons • The screen will return to its previous state if the AV receiver is operated. Press RECEIVER followed by an INPUT SELECTOR button. En-26...

  • Page 27: Controlling Contents Of Usb Or Network Devices

    (➔ page 90). Pressing this button twice selects the previous song. Note • The buttons you can use will differ depending on the devices and This button fast-reverses the current song. media used for playback. This button pauses playback. SEARCH You can toggle between the playback screen and the list screen during playback.

  • Page 28: Understanding Icons On The Display

    USB device from the USB port. Repeat receiver cannot read the iPod/iPhone. • If you connect an iPod or iPhone to the USB port, no sound will be output from the headphones jack. Shuffle • When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

  • Page 29: Playing A Usb Device

    (➔ page 114). • “Network/USB Features” • In this mode, video contents are not displayed, even if they are You can search for stations by categories such as genre or input from the AUX INPUT VIDEO jack on the AV receiver’s Press USB repeatedly to select the “USB(Front)”...

  • Page 30: Registering Other Internet Radio

    NET on the remote controller. depending on the type of data or audio format used by the • If you want to add a new station directly from “My Favorites”, 1. Press MENU with the station selected or while a Internet radio station, you may not be able to listen to some select an empty slot in the list and press MENU.

  • Page 31: Changing The Icon Layout On The Network Service Screen

    This section explains how to configure Windows Media Use q/w/e/r to select an icon to move, and then Player 11 so that the AV receiver can play the music files Use q/w/e/r to select “DLNA”, and press ENTER. press ENTER.

  • Page 32: Remote Playback

    TV that is connected to HDMI of my Player...” is checked. Note outputs. • Remote playback cannot be used in any of the following cases: Using Remote Playback – Network services are being used. Remote Playback means you can play the music files –...

  • Page 33: Playing Music Files On A Shared Folder

    Select and add “Everyone” from the pull-down menu and then click “Share”. Use q/w/e/r to select “Home Media”, and press • If this option is not available, verify that “View by:” is set to ENTER. “Category”. Select “Change advanced sharing settings”.

  • Page 34: Listening To Am/Fm Radio

    STEREO indicator lights as shown. the frequency of the radio station. Press TUNER to select either “AM” or “FM”. For example, to tune to 87.5 (FM), press 8, 7, 5 or 8, TUNED In this example, FM has been selected.
  • Page 35 For more information about HD Radio technology, visit: commences, that channel will be selected www.ibiquity.com automatically. www.hdradio.com • You can also use the remote controller’s number buttons to ■ select a preset directly. About HD Radio Stations HD Radio stations broadcast on the same AM and FM frequencies they’ve always used, and you can receive them...
  • Page 36 Note PS (Program Service) Station information • Multicast channels 2 through 8 are digital only, so you must select When tuned to an RDS station that’s broadcasting PS multicast channel #1 before you can change the Blend mode. information, the station’s name will be displayed. Pressing DISPLAY will display the frequency for 3 seconds.
  • Page 37 This is not a malfunction. If the current radio station is broadcasting TP (Traffic Current affairs Affairs • If the signal from an RDS station is weak, RDS data may be Program), “[TP]” will appear on the AV receiver’s Information Info displayed intermittently or not at all.

  • Page 38: Playing Audio And Video From Separate Sources

    Turning On & Basic Operations Playing Audio and Video from Separate Sources You can listen to the audio of one input source while watching the video of another. This function takes advantage of the fact that when an audio-only input source (TV/CD, PHONO) is selected, the video input source remains unchanged.

  • Page 39: Using Basic Functions

    Position the microphone at ear height of a seated With the supplied calibrated microphone, or other devices. Turn off the cell phone (even if it is not in use) Audyssey MultEQ ®...
  • Page 40 When prompted, repeat step 7. Note • The on-screen menus appear only on a TV that is connected • If your subwoofer does not have a volume control, disregard to HDMI OUT MAIN. If your TV is connected to other...
  • Page 41 Audyssey MultEQ XT32 Room Correction and Speaker Setup. • Ambient noise is too high. using e/r. • If the AV receiver is muted, it will be unmuted automatically The background noise is too loud. Remove the source of when Audyssey MultEQ XT32 Room Correction and Speaker the noise and try again.

  • Page 42: Using The Listening Modes

    This button selects the THX listening modes. PURE AUDIO button and indicator • Please note that THX recommends any THX main speakers be set to “80Hz(THX)”. If you set up your speakers using This button selects the Pure Audio listening mode.
  • Page 43 The illustration shows which speakers are activated in each The AV receiver’s listening modes can transform your channel. See “Speaker Configuration” for the speaker setup listening room into a movie theater or concert hall, with (➔ page 64). high fidelity and stunning surround sound.
  • Page 44 Turning On & Basic Operations After enabling the corresponding speakers, press RECEIVER followed by SP (speaker layout) repeatedly to select the speakers you want to use: front high, front wide, or surround back. After enabling the corresponding speakers, press RECEIVER followed by SP (speaker layout) repeatedly to select the layout you want to use.
  • Page 45 Full Mono In this mode, all speakers output the same simulates the natural reverberation of a large sound in mono, so the sound you hear is the hall. F u l M o n o...
  • Page 46 Input Speaker Source Layout Listening Mode Description Input Speaker In this mode, audio from the input source is Source Layout D xcn output without surround-sound processing. Pure Audio In this mode, the display and video circuitry D T S The speaker configuration (presence of...
  • Page 47 Research in human hearing has proven that Use this mode with video games, especially information from the Wide channels is those that bear the Dolby Pro Logic II logo. much more critical in the presentation of a • Dolby PLIIx Movie realistic soundstage than Back Surround •...
  • Page 48 The PLII/PLIIx and THX indicators light on the AV receiver’s display. • Dolby Pro Logic IIx Movie + THX Cinema • Dolby Pro Logic IIx Music + THX Music The combination of Dolby Pro Logic IIx and THX Cinema/Music modes can be used.
  • Page 49 T H X G a m e s the sound. back channel output. The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the • THX Ultra2 Music T H X S u r r output on the player side to PCM might bring better sound.

  • Page 50: Using The Home Menu

    AV receiver is turned on. Please wait Using the Home Menu until it becomes operable. • If no video signals are present, the thumbnails will be filled in Press ENTER to display the network service screen. The Home menu provides quick access to frequently used black.

  • Page 51: Using The Sleep Timer

    The sleep time can be set from 90 to 10 minutes in 10 Press TV/CD or GAME1. minute steps. “TV/CD” or “GAME1” appears on the AV receiver’s The SLEEP indicator lights on the AV receiver’s...

  • Page 52: Using The Whole House Mode

    – The “Powered Zone 2/3” setting is set to “Yes” and Direct, or Pure Audio. Zone 2/3 is turned on. • If you connect an iPod or iPhone to the USB port on the AV receiver, no sound will be output from the headphones jack. En-52...

  • Page 53: Using Easy Macros

    First, the related components stop and turn off. Second, the ALL OFF flashes twice. Press ACTIVITIES (MY MOVIE, MY TV, or AV receiver turns off. Finally, the TV turns off (or enters MY MUSIC) to start the Easy macro command. standby mode).

  • Page 54: Advanced Operations

    I n p u t A u d i o V i d e o I n f o r m a t i o n L i s t e n i n g M o d e En-54...

  • Page 55: Using The Audio Settings Of Quick Setup

    Note selected listening mode. –10dB to 0dB to +10dB in 2 dB steps. • These settings are not available in either of the following cases: Note You can boost or cut high-frequency sounds output. – The “Audio TV Out” setting is set to “On”...
  • Page 56 Dolby Digital, Dolby Digital Plus, or Dolby TrueHD. – Room Correction and Speaker Setup is completed. Note that • The Late Night function is set to “Off” when the AV receiver is “Audyssey” requires the “Audyssey MultEQ XT32 Full set to standby.
  • Page 57 • The Music Optimizer function only works with PCM digital Multichannel, DTS, DTS-HD High Resolution Audio, Note audio input signals with a sampling rate below 48 kHz and analog DTS-HD Master Audio, DTS Express, DSD, Dolby EX, audio input signals.

  • Page 58: Using The Setup Menu (Home)

    • The time until the screen saver activates itself can be changed 1ch: in the “Screen Saver” setting (➔ page 79). Audio signal is outputted from SW1 jack • The screen will return to its previous state if the AV receiver is operated. only. ENTER q/w/e/r 2ch: Audio signal is outputted from SW1 and SW2 jacks.

  • Page 59: About The Hybrid Standby Indicator

    (➔ page (➔ page IntelliVolume A/V Sync Name Edit Picture Adjust Note Audio Selector • If Zones are turned on or, if a mobile device connected to the Front Input (MHL) is charging, the HYBRID STANDBY indicator won’t light. En-59...

  • Page 60: Input/Output Assign

    Select this if your TV is connected to HDMI OUT HDMI output. MAIN. • This setting cannot be selected if the “Monitor Out” setting is set If you connect your TV to the HDMI output, the “Monitor to “Sub” or “Both”.
  • Page 61 “4K Upscaling”. Composite video, “- - - - -” or you will be unable to assign HDMI1 - HDMI8 • If the “Monitor Out” setting is set to “Sub”, this setting is fixed component video HDMI to other input selectors.
  • Page 62 Advanced Operations ■ • If you assign “- - - - -” to an input selector that is currently Component Video Input BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2, selected in “HDMI Through” (➔ page 80), the “HDMI PC, AUX, TV/CD, PHONO If you connect a video component to a component video Through”...

  • Page 63: Speaker Setup

    “Setup” you connect your CD player to the OPTICAL IN 1, you • When bi-amping is used, the AV receiver is able to drive up to 5.2 speakers in the main room. must assign “OPTICAL1” to the “TV/CD” input selector.
  • Page 64 “Digital Crossover”, Powered Zone 2 cannot be used. frequency bass sounds adequately, for example, speakers None • When the “Powered Zone 2” setting is set to “Yes” and Zone 2 with a good sized woofer. For smaller speakers, specify a Note is turned on, the surround back and front high speakers cannot be crossover frequency.
  • Page 65 With this setting, you can specify the cutoff frequency of 9.00m in 0.06 meter steps. setting is set to “1ch” or “2ch” and the “Front” setting is set to the LFE channel’s low-pass filter (LPF), which can be “Full Band” for the first time.
  • Page 66 (➔ page 64). • When the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, the surround back and front high speakers cannot be ■ Use q to select “Channel”, and then use e/r to used.
  • Page 67 The new THX Cinema, THX Music, and • This setting is fixed at “Yes” if “Loudness Plus” is set to “On”. • We recommend choosing a crossover value that creates no THX Games modes are tailored to apply the proper THX volume difference between “High”...

  • Page 68: Audio Adjust

    Adjusting “High Distance” pressing MODE/D (Blue). virtually shifts woofers behind tweeters. Adjusting “Low • In the case of usage of the bi-amped speakers, if there is a Main/Sub Distance” virtually shifts tweeters behind woofers. difference between the crossover frequency in the speakers’ built-...
  • Page 69 ■ PL IIx Music (2ch Input) • If the “Powered Zone 2” setting is set to “Yes” and Zone 2 is turned on, this setting cannot be selected. These settings apply to only 2-channel stereo sources.
  • Page 70 For example, if you Note • If the “Dolby Volume” setting is set to “Off”, this setting cannot see the following message: “DialogNorm: + 4 dB” in • When the “Dolby Volume” setting is set to “On”, be selected.
  • Page 71 With this setting, you can adjust the sound stage when using –QdB, –20dB, –10dB, or 0dB setting is not available. Audyssey DSX. With these settings, you can set the level of the LFE (Low Sound Program Edit Frequency Effects) channel individually for each input Note sources.

  • Page 72: Source Setup

    “Sound Program”. ■ Audyssey Select this setting for jazz or other music that has a • You cannot select the “Subwoofer” setting if you set it to “No” wider dynamic range. This setting should also be in “Speaker Configuration”. Movie: selected for TV content as that is usually mixed at •...
  • Page 73 Dynamic EQ selects the correct frequency Use e/r to set the level. At that level you can hear the mix as the mixers heard it. response and surround levels moment-by-moment at any If a component is noticeably louder than the others, use e Audyssey Dynamic EQ ®...
  • Page 74 Press CLR on the remote controller to delete all the characters you have input. 4-4. Name Edit BD/DVD Name • To name a radio preset, use TUNER to select AM or FM, and – then select the preset (➔ page 35).
  • Page 75 *4*6 With “Picture Mode”, you can change the following High settings to be suitable for the movie or game screen by one With Block Noise Reduction, you can remove the block operation; “Game Mode”, “Film Mode”, “Edge distortion that sometimes appears in the picture. Block Enhancement”, “Noise Reduction”, “Mosquito NR”,...
  • Page 76 (➔ page 60). Cool Select the desired output resolution. • “Picture Adjust” can be used when the USB input selector is With this setting, you can adjust the color temperature. 1080p/24: selected; however, only when iPod/iPhone is connected and Select this for 1080p output at 24 frames per second.

  • Page 77: Listening Mode Preset

    You can set priorities of audio output when there are both Note digital and analog inputs. To be continued • The setting will be reset to “Off” when you change the setting in Note “Audio Selector”. • This setting can be made only for an input source that is assigned to HDMI IN, COAXIAL IN, or OPTICAL IN.

  • Page 78: Miscellaneous

    Note ■ Dolby D/Dolby D Plus/TrueHD • If the absolute value is set to 82, “82.0Ref” will appear on the With this setting, you can specify the listening mode display and the THX indicator will flash. used when Dolby Digital or Dolby Digital Plus format ■...

  • Page 79: Hardware Setup

    AV receiver (➔ page 111). Note • When the setting is set to “On” and the menu is closed, the names of connected p-compatible components and “RIHD On” are displayed on the AV receiver. “Search…” → “(name)” → “RIHD On”...
  • Page 80 When enabling the HDMI Through function, regardless of Note • If “On” is selected and the audio can be output from the TV, the whether the AV receiver is on or in standby, both audio AV receiver will output no sound through its speakers. In this •...
  • Page 81 Upper Left, Upper Right, Lower Left, Lower Right playback with some sources. Note • The Auto Standby function does not work when Zone 2/3 is on. With this setting, you can set the position of preview • If you select “Disable”, you must configure the “IP Address”, thumbnails on the TV screen.

  • Page 82: Remote Controller Setup

    When enabled, the NET indicator will be dimly-lit while Note the AV receiver is in standby mode. Note that the indicator • If you do change the AV receiver’s remote ID, be sure to change ➔ page 59 may not light under certain conditions ( the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

  • Page 83: Multi Zone

    Multi Zone Note Main room • With this setup, the volume of Zone 2/3 is controlled by the AV In addition to the main listening room, you can also enjoy receiver. playback in the other room, or as we call Multi Zone. And, •...
  • Page 84 Connecting the Zone Speakers to an 12V Trigger Out Note Additional Amplifier • If you use HDMI OUT ZONE 2, make sure to set “Zone 2 When Zone 2/3 is turned on, the output from the 12V (➔ page HDMI” to “Use”...

  • Page 85: Controlling Multi Zone Components

    8RECEIVER ZONE 2 ZONE ■ Operating on the AV receiver • The Whole House Mode function shares the input source of main Press ZONE 2 or ZONE 3 (the Z2/Z3 indicator on room with Multi Zone (➔ page 52). Input selector buttons the AV receiver’s display flashes).

  • Page 86: Using The Remote Controller In Zone And Multiroom Control Kits

    AV receiver’s IR IN jack, as shown respectively. below. • If Zone 2 and the main room share the same input source, only an analog input signal is output. • If an HDMI component selected in Zone 2 outputs the sound other than PCM, the sound is not output from FRONT WIDE/ZONE 2 and ZONE 2 LINE OUT.
  • Page 87 IR OUT jack and placed in front of the other component’s remote control sensor. Infrared signals received at the AV receiver’s IR IN jack are fed through to the other component via the IR emitter. Signals picked up by the AV receiver’s remote control sensor are not output.

  • Page 88: Controlling Other Components

    • If you do adjust the volume control on your iPod/iPhone while it’s inserted in the RI Dock, be careful that it’s not set too loud Auto Power On before you reconnect your headphones.

  • Page 89: Controlling Your Ipod/Iphone

    Dock on or off. Also, your iPod/iPhone may not respond the Make an u connection and enter the remote control code first time you press this button, in which case you should press 81993 (with u). it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is •...

  • Page 90: Controlling Other Components

    ENTER. preprogrammed with remote control codes for controlling The menu of category selection appears. the components listed. You do not need to enter a remote Use q/w to select a category, and then press control code to control these components.

  • Page 91: Entering Remote Control Codes

    Within 30 seconds, use the number buttons to enter Note the 5-digit remote control code. • If any other button than the colored buttons is pressed, the The REMOTE MODE button flashes twice. operation will be cancelled. If the remote control code is not entered successfully, •...

  • Page 92: Remote Control Codes For Onkyo Components Connected Via Ri

    Resetting the REMOTE MODE Buttons For details on entering a remote control code for other components that are out of view, in a rack, for example. components, see “Entering Remote Control Codes” You can reset a REMOTE MODE button to its default (➔...
  • Page 93 AV receiver via HDMI. m RETURN C (Yellow) Use the following remote control codes: D (Blue) n CLR 32910/33101/33501/31612: Blu-ray Disc/DVD player with p The p supported by the AV receiver is the CEC system control function of the HDMI standard. En-93...
  • Page 94 Available buttons Note e 1, t (Reverse i 8SOURCE • With some components, certain buttons may not work as expected, and some may not work at all. Playback), 2, 5, 4, j MUTING • See “Controlling Your iPod/iPhone” about the operation of...

  • Page 95: Learning Commands

    • When the remote controller runs out of batteries, all commands If the command is learned successfully, the Learning Commands acquired will be lost and will have to be learned all over again. REMOTE MODE button flashes twice. Therefore, do not discard your other remote controllers.

  • Page 96: Using Normal Macros

    • Once you assign new macro commands, the previously registered controller mode. macro will no longer work. If you wish to retrieve it, you will have to reassign the commands with the macro-making. 2. Press 8RECEIVER to turn on the AV receiver.

  • Page 97: Appendix

    HDMI outputs. If your TV is ■ There’s no sound, or it’s very quiet If you have any trouble using the AV receiver, look for a connected to other video outputs, use the AV solution in this section. If you can’t resolve the issue receiver’s display when changing settings.
  • Page 98 Appendix ■ Can’t get 6.2/7.2 playback If the input signal format is set to “PCM” or “DTS”. Make sure the speakers are configured correctly. Set it to “Off”. If no surround back speakers, front wide and front — ■ The front high, front wide and surround back high speakers are connected, or the Zone 2/3 speakers ■...
  • Page 99 — On your TV, make sure that the video input to which — select “- - - - -” in the “HDMI Input” setting to bitstream stops, the AV receiver remains in DTS the AV receiver is connected is selected.
  • Page 100 To control an Onkyo component that’s not connected batteries, or old and new batteries. the Dock. If your iPod/iPhone is in a case, it may not via u, point the remote controller at the component. connect properly to the Dock. Always remove your...
  • Page 101 Zone 3. When a pair of headphones is connected, the listening — Can’t connect to the AV receiver from a Web mode is set to Stereo, unless it’s already set to Stereo, browser ■ Mono, Direct, or Pure Audio.
  • Page 102 AV receiver to standby. – 2 dB for the ZONE 2 OUT V and HDMI output. – 6 dB for the MONITOR OUT V output. • To by-pass the upconversion, set the “Picture Mode” setting to “Direct”...

  • Page 103: Firmware Update

    • If the USB device is partitioned, each section will be treated as an iPod/iPhone, USB or servers, etc. independent device. • If the USB device contains a lot of data, the AV receiver may take a while to read it. • Operation is not guaranteed for all USB devices, which includes the ability to power them.
  • Page 104 Please wait until it becomes operable. -10, The Ethernet cable was not detected. Select “Update via NET” and press ENTER. Reconnect the cable properly. Note that this option will not be available if there is no -11, -13, -21, Internet connection error.
  • Page 105 During the update process, the on-screen display may ONKAVR****_************.zip • Never plug or unplug an HDMI cable or a USB device during the disappear depending on the updated program. When Unzip the downloaded file. The following six files update process.
  • Page 106 Appendix Troubleshooting Case 1: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN If an error occurs, “Error!! *-**” is displayed on the AV http://www.onkyo.com/ receiver’s display. (Alpha-numeric characters on the front The Americas display are denoted by asterisks.) Refer to the following 18 Park Way, Upper Saddle River, N.J.

  • Page 107: Connection Tips And Video Signal Path

    (e.g., component video input passing through to component video Note output). • When “Monitor Out” is set to “Both”, the “Resolution” setting • To by-pass the upconversion, set the “Picture Mode” setting to cannot be selected (➔ page 60).
  • Page 108 Video input signals flow through the AV receiver as When the “Monitor Out” setting is set to “Analog” If signals are present at more than one input, the inputs will shown, with composite video and PC IN (Analog RGB) (➔ page 60), if the “Resolution”...
  • Page 109 When choosing a connection format, bear in mind that the AV receiver does not convert digital input signals for analog line outputs and vice versa. If signals are present at more than one input, the inputs will be selected automatically in the following order of priority: HDMI, digital, analog.
  • Page 110 Supported resolutions: [3840 × 2160 24/25/30 Hz], [4096 × 2160 24 Hz] When video signals of personal computers connected to PC IN are output from HDMI OUT SUB, they may not display properly on some TVs. Supported resolutions for HDMI OUT SUB (“Monitor Out” = “Sub”).

  • Page 111: Using An Rihd-Compatible Tv, Player, Or Recorder

    CEC (Consumer Electronics Control), which allows Players/Recorders • You can set on the menu screen of the TV to either output system control over HDMI and is part of the HDMI the audio from the speakers connected to the AV •...
  • Page 112 1. Turn on the power for all connected components. on the player models.) 2. Turn off the power of the TV, and confirm that the • Even if you set to output audio on the TV speakers, audio HDMI power of the connected components is turned off...

  • Page 113: About Hdmi

    PC are not supported. DSD and Multichannel PCM. • The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup.

  • Page 114: Network/Usb Features

    81). network is recommended. Although it’s possible to play • The AV receiver does not support PPPoE settings, so if you have The following diagram shows how you can connect the AV music on a computer that’s connected to the network a PPPoE-type Internet connection, you must use a PPPoE- receiver to your home network.
  • Page 115 Storage” will be displayed. Modem: 28.8 kbps • The computer or media server must be on the same • If you connect a USB hard disk drive to the AV receiver’s USB Sound card: 16-bit sound card network as the AV receiver.
  • Page 116 WAV files contain uncompressed PCM digital audio. • The sampling rate of 2.8224 MHz is supported. For server playback and playback from a USB device, the • Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz, ■ Dolby TrueHD (.vr/.mlp/.VR/.MLP) AV receiver supports the following music file formats.

  • Page 117: License And Trademark Information

    Please note that the use of this accessory with iPod or iPhone trademark or registered trademarks of MHL LLC in the United may affect wireless performance. States and other counties.” Apple TV is a trademark of Apple Inc., registered in the U.S. and other countries. En-117...

  • Page 118: Specifications

    Phono Overload 70 mV (MM 1 kHz 0.5% Direct) Ethernet Input IN 1, IN 2, IN 3, IN 4, IN 5, IN 6, IN 7, IN 8, Frequency Response 5 Hz - 100 kHz/+1 dB, –3 dB (Direct mode) IR Input...
  • Page 119 Appendix Memo En-119...
  • Page 120 The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700 Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong. Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com/ 1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai, China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.cn.onkyo.com/...
  • Page 121 AV receiver. Using Last.fm Internet Radio ......5 Select the desired service and press ENTER. • Some of the services don’t allow the use of multiple user The top page of the selected service appears. accounts.

  • Page 122: Pandora ® Internet Radio -Getting Started (U.s. Only)

    Don’t play the song for a month: your account and stations you can return to your If you are tired of a song, you can put the song to sleep Onkyo receiver and press enter to begin listening to and Pandora will not play it for one month.

  • Page 123: Using Rhapsody (U.s. Only)

    Use q/w to select a channel, and press ENTER or Search: 1 to start playback. Use q/w to select “Sign in to your account” and then You can search for music by Artist, Album, or Track. Playback starts and the playback screen appears.

  • Page 124: Using The Siriusxm Internet Radio (North American Only)

    Setup. If you don’t know your username or password, www.sirius.com). Be sure to read this agreement before many days are left in your trial. After the trial period call Sirius XM at (888) 539-7474 for assistance. you purchase your subscription. Sirius, XM and all related expires, if you want to continue listening to the service, marks and logos are trademarks of Sirius XM Radio Inc.

  • Page 125: Using Last.fm Internet Radio

    Last.fm is a music service that learns what you love... Tracks”, “Library” and “Neighbours”. If you have the existing Last.fm account, you can sign Your new Onkyo AV receiver is very clever. If you have a Account Info: in to your account to select “Sign in to your free Last.fm account, it will keep track of all the songs...

  • Page 126: Using Slacker Personal Radio

    Using Internet Radio You can control the tracks with the buttons on the Using Slacker Personal Radio remote control. If you do not have an account, create one on the Enabled buttons: 1, 3, 2, 6 Slacker website (www.slacker.com) with your ■...

  • Page 127: Using Mp3Tunes

    Using Internet Radio Playing Contents on the AV Receiver Using MP3tunes Use q/w to select a track and press ENTER or 1 to start playback. Listen to your music collection on your home stereo in A playback screen appears. complete digital fidelity without a personal computer plus •...
  • Page 128 Remarque Utilisation de SiriusXM Internet Radio Les éléments de menu suivants s’affichent : • Les services disponibles peuvent varier en fonction de la région. (Amérique du Nord uniquement) .... 4 Add new user : Remove this user : Appuyez sur NET.

  • Page 129: Pandora ® Internet Radio -Pour Commencer (États-Unis Uniquement)

    à votre récepteur Onkyo et appuyez Si vous en avez assez d’une chanson, vous pouvez sur entrée pour écouter votre webradio Pandora mettre la chanson « au repos » et Pandora ne la lira PANDORA, le logo PANDORA, et l’habillage personnalisée.

  • Page 130: Utilisation De Rhapsody (Etats-Unis Uniquement)

    à la liste My Favorites. consultez « Utilisation de plusieurs comptes » (➔ page Conseil L’identification peut être réalisée à partir de l’écran « Users ». • Vous pouvez supprimer des pistes, des albums et des canaux Rhapsody marqués de My Library. Fr-3...

  • Page 131: Utilisation De Siriusxm Internet Radio (Amérique Du Nord Uniquement)

    Saisissez votre nom utilisateur et votre mot de passe (voir www.sirius.com). Assurez-vous de lire cet accord le nombre de jours restants dans votre essai. Une fois la dans l’écran clavier suivant ou dans Configuration avant d’acquérir votre abonnement. Sirius, XM et tous les période d’essai expirée, si vous souhaitez continuer à...

  • Page 132: Utilisation De La Webradio Last.fm

    Vous pouvez lire des pistes des tags les mieux évalués. Tag Radio : Personal Station : Funk polonaise ? Death pop ? Pensez à un style et nous Vous pouvez lire des pistes de votre station vous divertirons avec pendant des heures.

  • Page 133: Utilisation De Slacker Personal Radio

    Vous pouvez contrôlez les pistes avec les touches sur Utilisation de Slacker Personal Radio la télécommande. Si vous ne possédez pas de compte, créez-en un à Boutons activés : 1, 3, 2, 6 partir du site Web de Slacker (www.slacker.com) à...
  • Page 134 Uso de Rhapsody (sólo EE.UU.)....3 Pulse MENU cuando aparezca la pantalla de Nota usuarios. • Los servicios disponibles pueden variar de una región a otra. Aparecerán los siguientes elementos del menú: Uso de SiriusXM Internet Radio (solo Add new user: Norteamérica) ...........

  • Page 135: Pandora ® Internet Radio -Primeros Pasos (Solo Ee.uu.)

    Delete this station: Pandora ® Internet Radio Utilice q/w para seleccionar la emisora en la lista de emisoras y luego pulse ENTER. Esto eliminará de forma permanente una emisora de –Primeros pasos (solo EE.UU.) su cuenta de Pandora. Toda la información sobre sus Se inicia la reproducción y aparece la pantalla de...

  • Page 136: Uso De Rhapsody (Sólo Ee.uu.)

    Marca las emisoras de Rhapsody que se están reproduciendo actualmente. Add to My Favorites: Añade una canción, emisora o lista de reproducción a la lista Mis favoritos. Consejo • Puede eliminar las canciones, los álbumes y las emisoras de Rhapsody marcados de Mi biblioteca. Es-3...

  • Page 137: Uso De Siriusxm Internet Radio (Solo Norteamérica)

    Lea atentamente este acuerdo antes de aparece a continuación o en la configuración web. Si muestra los días que quedan de la prueba. Una vez que comprar la suscripción. Sirius, XM y todas las marcas y no sabe su nombre de usuario o la contraseña, llame a...

  • Page 138: Uso De Last.fm Internet Radio

    Utilice q/w para seleccionar “Sign in to your account”, y luego pulse ENTER. Puede reproducir pistas de “Recently Listened Last.fm es un servicio musical que sabe lo que le gusta... Tracks”, “Library” y “Neighbours”. Si ya tiene una cuenta de Last.fm, puede acceder a ella Su nuevo receptor de AV Onkyo es muy inteligente.

  • Page 139: Uso De Slacker Personal Radio

    Puede controlar las pistas con los botones del Uso de Slacker Personal Radio mando a distancia. Si no tiene una cuenta, cree una en el sitio web de Botones activados: 1, 3, 2, 6 Slacker (www.slacker.com) con su ordenador. ■...
  • Page 140 Y1203-2 SN 29401189B (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. * 2 9 4 0 1 1 8 9 B *...
  • Page 141 If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver. Select the desired service and press ENTER. • Some of the services don’t allow the use of multiple user The top page of the selected service appears. accounts.
  • Page 142 Last.fm is a music service that learns what you love... Tracks”, “Library” and “Neighbours”. If you have the existing Last.fm account, you can sign Your new Onkyo AV receiver is very clever. If you have a Account Info: in to your account to select “Sign in to your free Last.fm account, it will keep track of all the songs...
  • Page 143 Die oberste Seite des ausgewählten Services erscheint. Nutzerkonten zu. • Sie können bis zu 10 Nutzerkonten speichern. • Um zwischen den Konten umzuschalten, müssen Sie sich zuerst aus Ihrem aktuellen Konto ausloggen und sich dann wieder auf dem „Users“ Bildschirm einloggen.
  • Page 144 Sender wiedergeben („Your Library“, „Your Die aktuellen Nutzungspreise und umfassende Infos sind Neighbourhood“ und „Your Recommendations“). unter www.last.fm/subscribe erhältlich Y1112-1 SN 29401229 (C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved. * 2 9 4 0 1 2 2 9 *...
  • Page 145 • Besides, it is not possible to add new codes to the existing remote controller presets. • Though the provided remote control codes are correct at the time of printing, they are subject to change by the manufacturer.
  • Page 146 • Cuando hay múltiples códigos relacionados con un fabricante, pruebe a introducirlos uno a uno • Quand il y a de multiples codes liés à un fabricant, essayez-les et entrez-les un par un jusqu’à ce hasta que coincida con su componente.
  • Page 147 “Remote Mode” e tasto “Display”. Beispiel „Remote Mode“ (Fernbedienungsmodus)-Taste und „Display“-Taste. Note: Hinweise: • I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi • Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet werden. zona.
  • Page 148 Genom att ange en kod från fjärrkontrollkodlistan, kan du aktivera relevanta REMOTE MODE/Remote-indicator eenmaal traag knipperen. förvalda kanaler för den utrustningen. • När det finns flera olika koder för en tillverkare ska du försöka att ange dem en och en tills de Opmerkingen: stämmer överens med din utrustning.
  • Page 149 • [RECEIVER （接收机）] 和多区域按钮不能输入遥控编码。 • [RECEIER] （接收機）和多區域按鈕不能輸入遙控編碼。 • 只能为 [TV （电视）] 输入电视遥控编码。 • 您只能為 [TV] （電視）輸入電視遙控編碼。 • 除 [RECEIVER （接收机）]、[TV （电视）] 和多区域按钮外，不能为 REMOTE MODE （遥 • 除 [RECEIVER] （接收機） 、[TV] （電視）和多區域按鈕外，您可針對 REMOTE MODE 控模式）按钮指定任何类别的遥控编码。 但是，这些按钮仍可用作输入选择器按钮，因 （遙控模式）按鈕指定任何類別的遙控編碼。 但是，這些按鈕仍可用作為輸入選擇器按 此，选择与设备所要连接的输入端对应的 REMOTE MODE（遥控模式） 按钮。 例如，如果...
  • Page 150 Remote Control Codes Dedicated Onkyo Receiver Cable Set Top Box Cable Set Top Box Cable/PVR Combination Default 62503 mio TV 02802 Toshiba 01509 Samsung 01877 Zone 2 62506 Motorola 01376, 00858, 01562, 01582 Scientific Atlanta 01877, 01982 01982, 01998, 02378...
  • Page 151 70157 Zonda 70157 Technology Revox 40029 Onkyo 71817 Cairn 70157 CD-R Sansui 40029 Optimus 70000, 70032 California Audio Labs 70029, 70303 Denon 70626, 70766 Sony 40243 Panasonic 70029, 70303 Cambridge 70157 70072 Thorens 40029 Philips 70626, 70157 Cambridge Audio 70157...
  • Page 152 Remote Control Codes Accessory Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Polk Audio 82228 Amstrad 00847, 01175, 01662, 01413, 01567 Durabrand 01284 01693 Chess 01334, 01626 Echostar 00775, 00853, 01323, Ansonic 02418 01409, 02527 Video - Accessory...
  • Page 153 Remote Control Codes Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Satellite Set Top Box Hama 01567 Leiko 01626 Pace 00847, 00853, 00887, Sat Industrie 01611 01175, 01323, 01356, Hanseatic 01100 Lemon 01334 SAT+ 01409 01423, 01662, 01693,...
  • Page 154 Remote Control Codes Satellite Set Top Box Satellite Set Top Box SAT/PVR Combination SAT/PVR Combination Star 00887 00642 BskyB 01175, 01662 Schneider 01206 Stream System 01300 00879, 01356 Bush 01645 Sedea Electronique 01206 Strong 00853, 00879, 01284, United 01251, 01626, 02418...
  • Page 155 Remote Control Codes Television Television Television Television Akai 10178, 10556, 10037, Basic Line 10556, 10037, 10668, Casio 10037 Dick Smith 10698 10714, 10715, 10208, 11037 Electronics Cathay 10037 11675 Baur 10037, 10195, 10512 Digatron 10037 10037 Akiba 10037 Beaumark 10178...
  • Page 156 Remote Control Codes Television Television Television Television Erres 10037 Genesis 10037 Hisense 10556, 10508, 10208, 10037 11363, 12098 10171 Genexxa 10037 11709 Hitachi 10150, 10178, 10037, 10037 10171, 11864, 11886 Jinfeng 10208 10634, 11037, 10508, Euroman 10037 Godrej 11585 Jinxing...
  • Page 157 Remote Control Codes Television Television Television Television Lifetec 10037, 10714, 10668, Medion 10556, 10037, 10714, Naiko 10037 Onix 10698 11037, 12001 10668, 11037, 10698, Nakimura 10037 Onkyo 11807, 13100, 13500 10512, 11248, 11585, Linsar 11585 National 10508, 10208 11667, 11709...
  • Page 158 Remote Control Codes Television Television Television Television Phoenix 10037 Reflex 10037, 10668, 11037 Sei-Sinudyne 10037 SunBriteTV 11610 Phonola 10556, 10037 Relisys 11585 Serie Dorada 10178 Sungoo 11248 Pioneer 10037, 10698, 10512, Remotec 10171, 10037 Shanghai 10208 Sunny 10037 11457, 11636, 12171...
  • Page 159 Remote Control Codes Television Television Television Technosonic 10556, 10625, 10499, Toyoda 11709 11365, 12098 Humax 20739 11324 TRANS-continents 10556, 10037, 10668, Walker 11667 Panasonic 20614, 20616 Techvision 11709 11037 Waltham 10037, 10668, 11037 Philips 20739 Techwood 11037, 11667 Transonic 10037, 10698, 10512,...
  • Page 160 31354, 32056, 32084, Go Video 30741 32434, 32689 C-Tech 31152 Luxman 30573 GoldStar 30741 Pioneer 30571, 30142, 30631, California Audio Labs 30490 Luxor 30713 31571, 32442, 32860 Goodmans 30713, 31152 Cambridge Audio 32808 Magnavox 30503, 30539, 30646, Polk Audio 30539...
  • Page 161 Remote Control Codes Blu-ray Disc Radionette 30741 Sylvania 30630, 30675 Yamaha 30490, 30539, 30646, Sony 31516, 32180 30817, 31354, 32298, Radiotone 30713 Symphonic 30675 Sylvania 30675 32299 30522, 30571, 32213, Tamashi 31394 Toshiba 32551, 32705, 33157 Zenith 30503, 30741 32587...
  • Page 162 Remote Control Codes DVD-R TV/DVD Combination Victor 31597 Magnavox 12372 Yamaha 30646 Matsui 11037, 30713 Zenith 30741 Medion 12719 Nordmende 12001 HD-DVD Odys 12719 Integra 32901, 33104 33504 Panasonic 12170 30741 Philips 11454, 10556, 11394, 30539 Microsoft 32083 Powerpoint 10698...
  • Page 163 Remote Control Codes Memo...
  • Page 164 Y1112-1 SN 29401094 (C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved. * 2 9 4 0 1 0 9 4 *...

Table of Contents