Onkyo TX-NR1010 Instruction Manual page 61

You can specify the output resolution for HDMI OUT
MAIN and COMPONENT VIDEO MONITOR OUT so
that the AV receiver upconverts the picture resolution as
necessary to match the resolution supported by your TV.
Tip
• You can see the picture by pressing ENTER to check the
"Resolution" setting for HDMI OUT MAIN (excluding NET
input source).
Note
• Depending on the incoming video signal, the video playback may
not be smooth or the vertical resolution may be lowered. In this
case select anything other than "1080p/24".
• With some TVs, there may be no picture when this setting is set
to "4K Upscaling".
• If the "Monitor Out" setting is set to "Sub", this setting is fixed
to "Through".
• If the "Monitor Out" setting is set to "Both", this setting is fixed
to "Auto".
*1 PC IN (Analog RGB input) signal is output at 480p
(480p/576p), 720p, 1080i resolution when the "Monitor Out"
setting is set to "Analog" (➔ page 60) and the "Resolution"
setting is set to "Through".
*2 These settings are not available when the "Monitor Out"
setting is set to "Analog" (➔ page 60).
HDMI Input
If you connect a video component to an HDMI input, you
must assign that input to an input selector. For example, if
you connect your Blu-ray Disc/DVD player to HDMI IN 2,
you must assign "HDMI2" to the "BD/DVD" input
selector.
If you've connected your TV to the AV receiver with an
HDMI cable, composite video and component video
sources can be upconverted * and output by the HDMI
output *1 . You can set this for each input selector by
selecting the "- - - - -" option. See "Video Connection
Formats" for more information on video signal flow and
(➔ page 107).
upconversion
Composite video,
component video
IN
OUT
Composite video,
component video
*1 This applies only when "Monitor Out" setting is set to other
than "Analog" (➔ page 60).
Here are the default assignments.
Input selector Default assignment
BD/DVD HDMI1
CBL/SAT HDMI2
STB/DVR HDMI3
GAME1 HDMI4
GAME2 HDMI5
PC HDMI6 *2
AUX FRONT (Fixed)
TV/CD - - - - -
PHONO - - - - -
*2 If you connect your personal computer to PC IN (Analog
RGB), you must assign "- - - - -" to the "PC" input selector.
En-61
■
BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, TV/CD, PHONO
HDMI1, HDMI2, HDMI3, HDMI4, HDMI5,
HDMI6, HDMI7, HDMI8:
Select the input to which the component has been
connected.
- - - - -:
Output composite video and component video
sources from the HDMI output. The video output
signal from the HDMI output is the one configured in
"Component Video Input".
Each HDMI input cannot be assigned to two input selectors
or more. When HDMI1 - HDMI8 have already been
assigned, you must first set any unused input selectors to
"- - - - -" or you will be unable to assign HDMI1 - HDMI8
HDMI to other input selectors.
Note
• For composite video and component video upconversion for the
HDMI output, the "Monitor Out" setting must be set to other
than "Analog"
must be set to "- - - - -". See "Connection Tips and Video Signal
HDMI
Path" for more information on video signal flow and
upconversion
• The assignment of input selector selected for Zone 2 cannot be
changed when the "Zone 2 HDMI" is set to "Use"
• If no video component is connected to the HDMI input (even if
the HDMI input is assigned), the AV receiver selects the video
source based on the setting of "Component Video Input".
• When an HDMI IN is assigned to an input selector as explained
here, the same HDMI IN will be set as a priority in the "Digital
Audio Input"
coaxial or optical audio input, make the appropriate selection in
the "Audio Selector" setting
• Do not assign an HDMI IN to the TV/CD selector while "HDMI
Control(RIHD)" is set to "On"
appropriate CEC (Consumer Electronics Control) operation will
not be guaranteed.
Advanced Operations
(➔ page 60), and the "HDMI Input" setting
(➔ page 107).
(➔ page
(➔ page 63). In this case, if you want to use the
(➔ page 77).
(➔ page 79), otherwise
To be continued
60).