Onkyo TX-NR515 Instruction Manual page 79

USB Device Playback
■
Can't access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support
the USB mass storage device class. However,
playback may not be possible with some USB devices
even if they conform to the USB mass storage device
class.
USB memory devices with security functions cannot
be played.
Others
■
Standby power consumption
In the following cases, the power consumption in
standby mode may reach up to a maximum of 8.3 W:
– The "HDMI Control(RIHD)" setting is set to
"On". (Depending on the TV status, the AV
receiver will enter standby mode as usual.)
– The "HDMI Through" setting is set to other than
"Off".
– The "Network Standby" setting is set to "On".
If an MHL-enabled mobile device is connected to the
AUX (front) input, the power consumption in standby
mode will increase.
■
The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian
and Asian models).
■
The speaker distance cannot be set as required
The values entered may be automatically adjusted
with values best-suited for your home theater.
■
The display doesn't work
The display is turned off when the Pure Audio
(European, Australian and Asian models) listening
mode is selected.
—
92
■
How do I change the language of a multiplex
source
Use the "Multiplex" setting in the "Audio Adjust"
menu to select "Main" or "Sub".
—
■
The u functions don't work
To use u, you must make an u connection and an
analog audio connection (RCA) between the
component and AV receiver, even if they are
connected digitally.
62, 64
While Zone 2 is selected, the u functions don't
work.
■
The functions System On/Auto Power On and
Direct Change don't work for components
connected via u
These functions don't work when Zone 2 is turned
16
on.
■
When performing "Automatic Speaker Setup",
the measurement fails and the message
"Ambient noise is too high." is displayed.
This can be caused by a malfunction in your speaker
—
unit. Check if the unit produces normal sounds.
■
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
—
On the AV receiver, press the input selector for the input
source that you want to set and the SETUP button
simultaneously. While holding down the input selector
button, press SETUP until "Video ATT :On" appears
on the AV receiver's display. Then, release both buttons.
En-79
To turn the setting off, repeat the above process so that
"Video ATT :Off" appears on the AV receiver's
—
display, and release the buttons.
• Video Attenuation
This setting can be made for the BD/DVD, CBL/SAT,
GAME, PC or USB input.
If you have a game console connected to the composite
video input, and the picture isn't very clear, you can
54
attenuate the gain.
Video ATT :Off: (default).
Video ATT :On: Gain is reduced by 2 dB.
■
18
If the picture on your TV/monitor connected to
the HDMI output(s) is unstable, try switching the
DeepColor function off
To turn off the DeepColor function, simultaneously
18
press the GAME and 8ON/STANDBY buttons on the
AV receiver. While holding down GAME, press
8ON/STANDBY until "Deep Color:Off" appears on
the AV receiver's display. Then, release both buttons.
To reactivate the DeepColor function, repeat the above
process until "Deep Color:On" appears on the AV
18
receiver's display and release the buttons.
The AV receiver contains a microcomputer for signal
processing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
—
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in.
Onkyo is not responsible for damages (such as CD rental
fees) due to unsuccessful recordings caused by the unit's
malfunction. Before you record important data, make
sure that the material will be recorded correctly.
Before disconnecting the power cord from the wall
outlet, set the AV receiver to standby.
Appendix