Self Diagnostic Function; Angle Data Table - Omron H8PS Manual

■ Self Diagnostic Function

The following displays will appear on the main display if an error occurs. If an error occurs, all outputs (including cam, pulse, and run outputs) will
be turned OFF.
Display Meaning
e00
Origin designation data error
e11
Memory error: RAM error
e12
Memory error: Checksum error
e13
CPU error
e21
Response speed exceeded
e22
Encoder data error
e23
Encoder resolution inconsistent
e24
Encoder disconnected

Angle Data Table

To assist with programming when using an Encoder with a resolution of 256/rotation, displays and settings may be done by conversion to 360
degrees by setting a pin on the DIP switch inside the front cover. The following table shows the conversions.
0 1 2 3 4 5
0 1 3 4 6 7
16 17 18 19 20 21
23 24 25 27 28 30
32 33 34 35 36 37
45
46 48 49 51 52
48 49 50 51 52 53
68
69 70 72 73 75
64 65 66 67 68 69
90
91 93 94 96 97
80 81 82 83 84 85
113
114 115 117 118 120
96 97 98 99 100 101
135
136 138 139 141 142
112 113 114 115 116 117
158
159 160 162 163 165
128 129 130 131 132 133
180
181 183 184 186 187
144 145 146 147 148 149
203
204 205 207 208 210
160 161 162 163 164 165
225
226 228 229 231 232
176 177 178 179 180 181
248 249 250 252 253 255
192 193 194 195 196 197
270 271 273 274 276 277
208 209 210 211 212 213
293 294 295 297 298 300
224 225 226 227 228 229
315 316 318 319 321 322
240 241 242 243 244 245
338 339 340 342 343 345
Press the CLEAR Key for at least 3 s. All settings, including the origin designation data, will be
initialized.
Cycle the power supply.
Press the CLEAR Key for at least 3 s. All settings, including the origin designation data, will be
initialized.
Cycle the power supply.
The Encoder is rotating faster than the allowable range. Reduce the speed to within the allowable
range. Then cycle the power supply or switch to Programming Mode and then to Run Mode.
There are surges or noise around the product or in the wiring. Check the wiring and protect the
product from surges and noise. Then cycle the power supply.
Set the Encoder resolution according to the specifications of the Encoder. Then cycle the power
supply.
Connect the Encoder connector properly. Then, cycle the power supply or switch to Programming
Mode and then to Run Mode.
6 7 8 9 10 11
8 10 11 13 14 15
22 23 24 25 26 27
31 32 34 35 37 38
38 39 40 41 42 43
53 55 56 58 59 60
54 55 56 57 58 59
76 77 79 80 82 83
70 71 72 73 74 75
98 100 101 103 104 105
86 87 88 89 90 91
121 122 124 125 127 128
102 103 104 105 106 107
143 145 146 148 149 150
118 119 120 121 122 123
166 167 169 170 172 173
134 135 136 137 138 139
188 190 191 193 194 195
150 151 152 153 154 155
211 212 214 215 217 218
166 167 168 169 170 171
233 235 236 238 239 240
182 183 184 185 186 187
256 257 259 260 262 263
198 199 200 201 202 203
278 280 281 283 284 285
214 215 216 217 218 219
301 302 304 305 307 308
230 231 232 233 234 235
323 325 326 328 329 330
246 247 248 249 250 251
346 347 349 350 352 353
Recovery method
12 13 14 15
17 18 20 21
28 29 30 31
39 41 42 44
44 45 46 47
66
62 63 65
60 61 62 63
89
84 86 87
76 77 78 79
111
107 108 110
92 93 94 95
134
129 131 132
108 109 110 111
156
152 153 155
124 125 126 127
179
174 176 177
140 141 142 143
201
197 198 200
156 157 158 159
224
219 221 222
172 173 174 175
246
242 243 245
188 189 190 191
264 266 267 269
How to Use the Table
204 205 206 207
287 288 290 291
220 221 222 223
309 311 312 314
236 237 238 239
332 333 335 336
252 253 254 255
354 356 357 359
Cam Positioner
256 display (Encoder output data)
0 1
0 1
360 display (360 converted data)
H8PS
31