MCR-B043/MCR-B043D/NS-BP83
■ UPDATING FIRMWARE / ファームウェアのアップデート
When the following parts are replaced, the firmware must
be updated to the latest version.
Replaced parts
交換部品
MAIN P.C.B.
Microprocessor (IC102) / マイコン(IC102)
FLASH ROM (IC304) of CD/USB/DSP controller
CD/USB/DSP コントローラーのフラッシュロム(IC304)
● Confirmation of firmware version and checksum
Before and after updating the firmware, check the
firmware version and checksum by using the self-
diagnostic function menu.
Start up the self-diagnostic function and select "1.
FIRMWARE VERSION" menu.
Using the sub-menu, have the firmware version and
checksum displayed, and note them down.
(For details, refer to "SELF-DIAGNOSTIC FUNCTION")
*
When the firmware version is different from
written one after updating, perform the updating
procedure again from the beginning.
● Initializing the back-up IC
(EEPROM: IC104 on MAIN (1) P.C.B.)
After updating the firmware, the back-up IC MUST
be initialized by the following procedure to store the
setting information (tuner preset, clock) properly.
Start up the self-diagnostic function and select "15.
FACTORY PRESET" menu.
(For details, refer to "SELF-DIAGNOSTIC FUNCTION")
Select "15-2 RESERVED", press the " " (Power) key
to turn off the power once and turn on the power
again. Then the back-up IC is initialized.
Updating microprocessor firmware
● Required tools
•
Firmware downloader program
....................................................... FlashSta.exe
•
Firmware ......................... MCRB043_xx_xxxx.mot
•
RS-232C cross cable "D-sub 9 pin female"
(Specifications)
Pin No.2 RxD
Pin No.3 TxD
Pin No.5 GND
Pin No.7 RTS
Pin No.8 CTS
•
RS-232C conversion adaptor
18
MCRB043_xx_xxxx.id
Pin No.2 RxD
Pin No.3 TxD
Pin No.5 GND
Pin No.7 RTS
Pin No.8 CTS
(version 4.0, Part No.: WZ064500)
下記の部品を交換した場合、ファームウェアを最新バー
ジョンにアップデートする必要があります。
Firmware to be updated / アップデートするファームウェア
Microprocessor firmware
マイコンファームウェア
CD/USB/DSP コントローラーファームウェア
yes
yes
● ファームウェアのバージョンとチェックサムの確認
ファームウェアのアップデートの前後に、ファーム
ウェアのバージョンとチェックサムをダイアグで確
認します。
ダイアグを起動し、"1. FIRMWARE VERSION" メニュー
を選択します。
サ ブ メ ニ ュ ー で フ ァ ー ム ウ ェ ア の バ ー ジ ョ ン と
チェックサムを表示し、それらを書きとめます。
(詳細は "ダイアグ" を参照してください。 )
※ アップデート後、ファームウェアのバージョンが
書き込まれたものと異なる場合、アップデートの
操作を最初からやり直してください。
● バックアップ IC の初期化
(EEPROM:MAIN(1)P.C.B. の IC104)
ファームウェアのアップデート後、 設定情報(チュー
ナープリセット、時計)を正常に保存するために、
下記の方法でバックアップ IC を初期化する必要が
あります。
本機のダイアグを起動し、"15. FACTORY PRESET" メ
ニューを選択します。
(詳細は "ダイアグ" を参照してください。 )
"15-2 RESERVED" を選択し、" "(電源)キーを押し
て電源を一度きってから、もう一度電源を入れると
バックアップ IC が初期化されます。
マイコンファームウェアのアップデート
● 必要なツール
・ ファームウェア書き込み用プログラム
. .............................................................................. FlashSta.exe
・ ファームウェア . ......................MCRB043̲xx̲xxxx.mot
・ RS-232C クロスケーブル "D-sub 9pin メス"
(仕様)
Pin No.2 RxD
Pin No.3 TxD
Pin No.5 GND
Pin No.7 RTS
Pin No.8 CTS
・ RS-232C 変換アダプター
(バージョン 4.0、部品番号:WZ064500)
CD/USB/DSP controller firmware
yes
yes
MCRB043̲xx̲xxxx.id
Pin No.2 RxD
Pin No.3 TxD
Pin No.5 GND
Pin No.7 RTS
Pin No.8 CTS