Pitch Change B (Classic Bank); Pitch Change C (Classic Bank) - Yamaha SPX2000 Owner's Manual

Pitch Change B (CLASSIC bank)

This is a pitch change effect based on earlier models of the SPX series. It is equivalent to the Dual Pitch effect of the PRESET
bank. The two effect sounds will be mixed and output.
Each aspect of the sound is controlled by the following effect parameters.
1 PITCH, 1 FINE, 1 DLY
Effect sound 1:
2 PITCH, 2 FINE, 2 DLY
Effect sound 2:
OUT LVL, MIX BAL.
Output level:
Parameter details
■Basic parameters
Parameter name Range
1 PITCH
–12—+12
2 PITCH
1 FINE
–100—+100
2 FINE
1 DLY
0.0—1000.0 ms
2 DLY
OUT LVL 0—100%
MIX BAL. 0—100%
Effect list
The following table shows the default parameter values for the effect belonging to the Pitch Change B type (CLASSIC bank).
No. Effect name
20 PITCH CHANGE B

Pitch Change C (CLASSIC bank)

This is a pitch change effect based on earlier models of the SPX series. It is equivalent to the Dual Pitch effect of the PRESET
bank. The two effect sounds will be output separately from the L and R channels.
Each aspect of the sound is controlled by the following effect parameters.
L PITCH, L FINE, L DLY
L channel effect sound:
R PITCH, R FINE, R DLY
R channel effect sound:
OUT LVL, MIX BAL.
Output level:
Parameter details
■Basic parameters
Parameter name Range
L PITCH
–12—+12
R PITCH
L FINE
–100—+100
R FINE
L DLY
0.0—1000.0 ms
R DLY
OUT LVL 0—100%
MIX BAL. 0—100%
Effect list
The following table shows the default parameter values for the effect belonging to the Pitch Change C type (CLASSIC bank).
No. Effect name
21 PITCH CHANGE C
Amount of pitch change, set in semitone steps. Positive (+) settings make the pitch higher than the
original sound, and negative (–) settings make it lower.
Amount of pitch change, set in cents (1/100th of a semitone). Positive (+) settings make the pitch
higher than the original sound, and negative (–) settings make it lower.
Delay of the effect sound relative to the original sound.
Output level after the original sound and effect sound have been mixed. Decrease this value if you
want to lower the output. At a setting of 0% there will be no output.
Balance between the original sound and effect sound. At a setting of 0% only the original sound
will be output; at a setting of 100% only the effect sound will be output.
1 PITCH 1 FINE 1 DLY
0 +8 0.1 ms
Amount of pitch change, set in semitone steps. Positive (+) settings make the pitch higher than the
original sound, and negative (–) settings make it lower.
Amount of pitch change, set in cents (1/100th of a semitone). Positive (+) settings make the pitch
higher than the original sound, and negative (–) settings make it lower.
Delay of the effect sound relative to the original sound.
Output level after the original sound and effect sound have been mixed. Decrease this value if you
want to lower the output. At a setting of 0% there will be no output.
Balance between the original sound and effect sound. At a setting of 0% only the original sound
will be output; at a setting of 100% only the effect sound will be output.
L PITCH L FINE L DLY
0 +8 0.1 ms
Explanation
2 PITCH 2 FINE 2 DLY
0 –8 20.0 ms
Explanation
R PITCH R FINE R DLY
0 –8 0.1 ms
SPX2000—Owner's Manual
OUT LVL MIX BAL.
100% 100%
OUT LVL MIX BAL.
100% 100%
65