Table of Contents
Advertisement
S
M
I
F
41 [ ON TMR ]
Set the ON Timer time.
42 [ OPN.MSG ]
Selects the Opening Message that appears when the radio is pow-
ered on.
43 [ PAGER ]
Enables/disables the Enhanced CTCSS Paging & Code Squelch
function.
44 [ PAG.ABK ]
Enables/disables the Answer Back function of the Enhanced CTCSS
Paging & Code Squelch.
45 [ PAG.CDR ]
Setting the Receiver Pager Code for the Enhanced CTCSS Paging
& Code Squelch.
46 [ PAG.CDT ]
Setting the Transmitting Pager Code for the Enhanced CTCSS Pag-
ing & Code Squelch.
47 [ PSWD ]
Programs and activates the Password feature.
48 [ PTT.DLY ]
Select the time delay between when the PTT switch is pressed
and the carrier is transmitted.
49 [ RESUME ]
Selects the Scan Resume mode.
50 [ RF SQL ]
Adjusts the RF Squelch threshold level.
51 [ RPT ]
Sets the Repeater Shift Direction.
52 [ RX MD ]
Selects the receiving mode.
53 [ RXSAVE ]
Selects the Receive-mode Battery Saver interval ("sleep" ratio)
54 [ S SRCH ]
Selects the Smart Search Sweep mode.
55 [ SCN.LMP ]
Enables/Disables the Scan lamp while paused.
56 [ SHIFT ]
Sets the magnitude of the repeater Shift.
57 [ SKIP ]
Selects the Memory Scan "Skip" channel-selection mode.
58 [ SPLIT ]
Enables/Disables split CTCSS/DCS coding.
59 [ SQL ]
Sets the Squelch threshold level.
60 [ SQL.TYP ]
Selects the Tone Encoder and/or Decoder mode.
61 [ STEP ]
Setting of the synthesizer steps.
62 [ SU1.ALT ]
Selects the measurement units for the altimeter, and correcting the
altimeter.
63 [ SU1.BRM ]
Selects the measurement units for the Barometric Pressure, and
correcting the Barometric Pressure.
64 [ SU1.SET ]
Selects the display of the sensor units' information.
65 [ TEMP ]
Indicates indicate the current temperature inside the transceivre's
case and selects the measurement units ("°F" or "°C") for the tem-
perature sensor.
66 [ TN FRQ ]
Setting of the CTCSS Tone Frequency.
67 [ TOT ]
Setting of the TOT time.
68 [ TS MUT ]
Enables/Disables the receiver audio output during the Tone Serch
Scanner is activated.
69 [ TS SPD ]
Selects the Tone Serch Scanner speed.
70 [ TXSAVE ]
Enables/Disables the Transmitter Battery Saver.
71 [ VFO MD ]
Enables or disables the VFO band edge limiting for the current
band.
72 [ WAKEUP ]
Setting of the Wakeup feature.
73 [ WX ALT ]
Enables/Disables the Weather Alert Scan feature.
1: Depends on the transceiver version.
2: Depends on the frequency band.
3: Requires optional SU-1.
VX-6R O
M
S
M
A
( D
: B
OFF /
00H10M (00:10) - 24H00M (24:00)
(10 minutes multiples)
DC / MSG / OFF
OFF / ON
OFF / ON
(05 _ 47)
(05 _ 47)
OFF / 20MS / 50MS /
100MS / 200MS
3 SEC / 5 SEC / 10 SEC /
BUSY / HOLD
OFF / S1 / S2 / S3 / S4 / S5 /
S6 / S7 / S8 / S9 / S9+
SIMP / –RPT / +RPT
AUTO / N-FM / AM / W-FM
200 MS / 300 MS / 500 MS /
1 S / 2 S / OFF
SINGLE / CONT
ON / OFF
0.00 - 149.95 MHz
(50 kHz increments)
OFF / SKIP / ONLY
OFF / ON
LVL 0 - LVL 15 (Narrow FM: LVL 1),
LVL 0 - LVL 8 (Wide FM: LVL 2)
OFF / TONE / T SQL /
DCS / RV TN
5.0k / 10.0k / 12.5k / 15.0k / 20.0k /
25.0k / 50.0k / 100.0k / AUTO
M / Ft
Offset: –1000 - 0 - +1000
HP / MB / HG / IC
Offset: –1000 - 0 - +1000
OFF / BARO / ALTI
50 standard CTCSS tones (100 Hz)
OFF / 1MIN / 3MIN / 5MIN / 10MIN
ON / OFF
FAST / LOW
OFF / ON
BAND / ALL
OFF / 5S / 10S / 20S / 30S / EAI
OFF / ON
M
V
)
I
--
2
1, 3
1, 3
3
--
89
Advertisement
Table of Contents
