Heat & Glo STELLAR 3-IDOD-24-G Manual page 16

Firebox
INCHES [MM]
Top Height
A
42-1/2
3-IDOD-24-G
[1,068]
42-1/2
4-IDOD-24-G
[1,068]
42-1/2
5-IDOD-24-G
[1,068]
42-1/2
6-IDOD-24-G
[1,068]
42-1/2
7-IDOD-24-G
[1,068]
42-1/2
8-IDOD-24-G
[1,068]
54-1/32
3-IDOD-36-G
[1,322]
54-1/32
4-IDOD-36-G
[1,322]
54-1/32
5-IDOD-36-G
[1,322]
54-1/32
6-IDOD-36-G
[1,322]
54-1/32
7-IDOD-36-G
[1,322]
54-1/32
8-IDOD-36-G
[1,322]
3'-5' = 8-1/4" [209] **
6'-8' = 7-1/4" [184]
7 [178] ****
C
Page 16
5 - FRAMING & MANTEL REQUIREMENTS
Interior
Overall Framing
Framing
Height
Height
Width
B C D
51 57 44-17/32
[1,295] [1,448] [1,131]
51 57 56-17/32
[1,295] [1,448] [1,436]
51 57 68-17/32
[1,295] [1,448] [2.046]
51 57 80-17/32
[1,295] [1,448] [2,046]
51 57 92-17/32
[1,295] [1,448] [2,350]
51 57 104-17/32
[1,295] [1,448] [2,655]
63 69 44-17/32
[1,600] [1,753] [1,131]
63 69 56-17/32
[1,600] [1,753] [1,436]
63 69 68-17/32
[1,600] [1,753] [2.046]
63 69 80-17/32
[1,600] [1,753] [2,046]
63 69 92-17/32
[1,600] [1,753] [2,350]
63 69 104-17/32
[1,600] [1,753] [2,655]
23 [584] *
1
Exterior Refer to Section 5 (Non-combustible Zone) for more
information on the 1/2" [13] clearance standoffs.
Framing
Width
X - WALL SHEATHING THICKNESS
E
Y = WALL FRAMING THICKNESS
44-17/32
Z = INTERIOR SHEATHING PLUS FINISH THICKNESS
[1,131]
56-17/32
* 23" [584] is the dimension from the back of the
[1,436]
nailing flange to the tip of the interior clearance
68-17/32
standoff. Interior framing will shift based on material thickness.
[2.046]
80-17/32
** There is a 1" [25] clearance to combustibles around the flue.
[2,046]
Framing thickness (X + Y) must be observed to maintain this
92-17/32
clearance or a 45 degree vent component must be used.
[2,350]
104-17/32 *** Install mineral wood insulation in the 1" [25] gap between the
[2,655]
fireplace sides and wall. Do not use fiberglass or any type of
insulation with paper or plastic facing.
44-17/32
[1,131]
**** Mineral wool may be installed between the
56-17/32
fireplace top and header. Do not use fiberglass or any type of
[1,436]
insulation with paper or plastic facing.
68-17/32
[2.046]
80-17/32
[2,046]
92-17/32
[2,350]
104-17/32
[2,655]
X
1/2 [13]
B
A
EXTERIOR
YOU WILL NEED TO DETERMINE
THE DEPTH DIMENSION FOR YOUR
INSTALLATON BASED ON THE
THICKNESS OF THE
FINISHING AND FRAMING
MATERIALS YOU ARE USING.
Y
23 [584]-X-Y
23 [584]-X
Z
C
INTERIOR
INS_CUST