Delivery Of The System And The Instruction Manual; Guarantee And Responsibility - Riello RDB 2.2 BX 12-18 Installation, Use And Maintenance Instructions

2.1.4 Delivery of the system and the instruction
manual
When the system is delivered, it is important that:
 the instruction manual is delivered to the user by the system
manufacturer, with the recommendation to keep it in the
room where the heat generator is to be installed.
 The instruction manual shows:
– the serial number of the burner;
.........................................................................................
– the address and telephone number of the nearest Assis-
tance Centre.
.........................................................................................
.........................................................................................
.........................................................................................
2.2

Guarantee and responsibility

The Manufacturer guarantees its new products from the date of
installation, in accordance with the regulations in force and/or the
sales contract. At the moment of the first start-up, check that the
burner is integral and complete.
Failure to observe the information given in this
manual, operating negligence, incorrect installa-
tion and carrying out of non authorised modifica-
tions will result in the annulment by the
WARNING
manufacturer of the guarantee that it supplies with
the burner.
In particular, the rights to the guarantee and the responsibility will
no longer be valid, in the event of damage to things or injury to
people, if such damage/injury was due to any of the following
causes:
 incorrect installation, start-up, use and maintenance of the
burner;
 improper, incorrect or unreasonable use of the burner;
 intervention of unqualified personnel;
 carrying out of unauthorised modifications on the equipment;
 use of the burner with safety devices that are faulty, incor-
rectly applied and/or not working;
 installation of untested supplementary components on the
burner;
 powering of the burner with unsuitable fuels;
 faults in the fuel supply system;
 continuation of use of the burner when a fault has occurred;
 repairs and/or overhauls incorrectly carried out;
 modification of the combustion chamber with inserts that
prevent the regular development of the structurally estab-
lished flame;
 insufficient and inappropriate surveillance and care of those
burner components most likely to be subject to wear and
tear;
 use of non-original components, including spare parts, kits,
accessories and optional;
 force majeure.
The manufacturer furthermore declines any and every re-
sponsibility for the failure to observe the contents of this
manual.
Information and general warnings
 The system supplier must carefully inform the user about:
The manufacturer's warranty is subject to correct burner, appli-
ance and application matching, and set up in line with Manufac-
turer's instructions and guidelines. All components within the
hydraulic circuit suitable for biofuel use and supplied by the man-
ufacturer will be identified as bio-compatible. No warranty is given
in relation to the use of components which are not so identified
with biofuel blends. If in any doubt please contact the manufac-
turer for further advice.
If any burners are used with fuel with a bio content >30% then the
components within the hydraulic circuit may be affected and are
not covered under warranty. The hydraulic circuit consists of:
– pump
– hydraulic ram (where applicable)
– valve block
– flexible oil lines (considered as a consumable component)
1
2
3
5
GB
– the use of the system;
– any further tests that may be required before activating the
system;
– maintenance, and the need to have the system checked at
least once a year by a representative of the manufacturer
or another specialised technician.
To ensure a periodic check, the manufacturer recom-
mends the drawing up of a Maintenance Contract.
Irrespective of any warranty given by the manufacturer in
relation to normal use and manufacturing defects, when
fuels not meeting the relevant standards are used, or where
fuel storage issues have not been addressed correctly, or
the equipment used is not compatible, if failures occur which
are directly or indirectly attributed to such issues and/or to
the non-observance of this guidance, then no warranty or
liability is implied or accepted by the manufacturer.
The manufacturer has carefully chosen the specification of
the bio-compatible components including the flexible oil
lines to protect the pump, safety value and nozzle. The
manufacturer warranty is dependent upon the use of genu-
ine components including the oil lines, being used.
The manufacturer warranty does not cover defects arising
from incorrect commissioning or servicing by non manufac-
turer employed service engineers, and any issues impacting
the burner arising from external site related issues.
20130035