Returning To The Initial Settings; Remote Control Codes Of; Other Manufacturers Already Preset - Pioneer VSX-D2S Operating Instructions Manual

REMOTE CONTROL
4. Press the CD receiver input selector button.
@ The CONTROL MODE buttons go out, and then flash at random.
(Registration is completed)
5. Press the CD CONTROL MODE button.
© The CD button flashes.
6. Press the PLAY (>) button.
© The CD button goes out, and then the CONTROL MODE buttons
flash at random. (Registration is completed)
7. Press the MULTI COMMAND button.
@ The CONTROL MODE buttons light in sequence (This means
that registration has been completed), and then the VCR 1, VCR
2, and TV buttons flash in sequence.
8. Press the EDIT button.
@ The EDIT mode is canceled.
If you press the MULTI COMMAND button, these remote control
signals are transmitted in the order programmed, so if CONTROL IN/
OUT is connected (refer to page 28), and if remote control signals
can reach both the receiver and CD player sensor windows, power to
the receiver switches on, the input selector switches to CD, and the
CD player starts playing. (When the CD player's power cord is
plugged into the receiver's switched AC OUTLET.)
NOTE:
© After pressing the seventh command, the MULTI-EDIT mode is:
registered automatically (The VCR 1, VCR 2, and TV CONTROL
MODE buttons flash in sequence}, but the EDIT mode is not
canceled. To cancel the EDIT mode, press the EDIT button.
e After memorizing six or less commands, if you cancel the EDIT
mode without pressing the MULTI COMMAND button again, all the
registered commands are cleared, leaving the previous commands
as they were.
© /fa button is for transmission, even if itis notan operation button in
the selected CONTROL MODE, registration is still possible. (Buttons
such as the VCR 1 t+).
In this case, during signal transmission, the CONTROL MODE
button momentarily lights, but the remote contro! code is not
transmitted.
© /f the component to be operated is installed at a distance, if there is
an obstacle between a specific component sensor window and the
remote control, or if component operation speeds are very
different, MULTI-COMMAND operation may be incorrect. When
repeating operations, first return to the initial settings for each
component. For operations such as power ON/OFF, if components
are switched ON, they can be switched OFF by transmitting a signal.
RETURNING TO THE INITIAL SETTINGS
Initialization of particular CONTROL MODES
1. Remove the battery compartment cover.
2. While pressing the M.CLEAR button inside the cover, press
the button for the CONTROL MODE (for example VCR 1) you
want to initialize.
® For example, if you initialize VCR 1 using the method mentioned
above, the CONTROL MODE button lights for about one
second, and the VCR 1 operation buttons are initialized.
M.CLEAR button
Initializing the entire memory
1. Remove the battery compartment cover.
2. While pressing the M.CLEAR button inside the cover, press
the RESET button.
© Do not release the M.CLEAR button before releasing the RESET
button. While pressing the M.CLEAR button, press the RESET
button, and quickly release.
Initialization is not possible if the buttons are pressed in the
reverse order.
e All the CONTROL MODE operation buttons are initialized, and
data in the MULT! COMMAND button is cleared.
" M.CLEAR button
RESET button
REMOTE CONTROL CODES OF OTHER
MANUFACTURERS ALREADY PRESET
The following table shows the PRESET MODE buttons (1 to 12) used
to call up the remote control codes of other manufacturers. Preset
remote control signals in the table, however, may not always enable
operation. If operation is not possible, switch to the LEARN mode,
and learn signals from the VCR or TV remote controi. Nunnbers in
parenthesis indicate a reduced possibility of operation.
[—Manutecwrer [Wid
RCA 1, (10) (1), 6)
ZENITH 3 (3), 4)
GE 8, (11), (1) (1), 8)
SONY
4
4
TOSHIBA 5 5, ()
HITACHI 6, (10) 6
PHILIPS
JVC
PANASONIC
MITSUBISHI 9, (10)
SANYO = 10, (12)
SHARP (2) 2
GOLD STAR (10) (1
MAGNAVOX (7), (10), (12) (8), 9)
SYLVANIA (7), (40), (12) (8), 9)
QUASER 8 g
FISHER 2 12, (0)
WARD'S (2), (7), (10), (11) (2
43
<.R B15 >