Pioneer VSX-D6025 Operating Instructions Manual page 39

REMOTE CONTROL OPERATION
MULTI-EDIT MODE
A maximum of seven commands can be programmed into MULTI
COMMAND button. This enables a series of signals to be transmitted
simply by pushing the MULT! COMMAND button.
(Example} Programming the following three commands into the MULTI
COMMAND button.
@ RECEIVER POWER
@ RECEIVER FUNCTION CD
@ CD PLAY (>)
1. Press the EDIT button. (Switches to the EDIT mode)
© The VCR 1, VCR 2, and TV CONTROL MODE buttons flash in
sequence,
. Press the MULTI COMMAND button. (Switches to the MULTI-EDIT
mode)
@ The CONTROL MODE buttons flash at random.
. Press the RECEIVER POWER button.
¢@ The CONTROL MODE buttons go out, and then flash at random.
(Registration is completed)
. Press the CD receiver input selector button.
© The CONTROL MODE buttons go out, and then flash at random.
(Registration is completed)
. Press the CD CONTROL MODE button.
* The CD button flashes.
Press the PLAY ( ) button.
* The CD button goes out, and then the CONTROL MODE buttons
flash at random. (Registration is completed)
. Press the MULT] COMMAND button.
© The CONTROL MODE buttons fight in sequence, (This means that
registration has been completed), and then the VCR 1, VCR 2, and
TV buttons flash in sequence.
8. Press the EDIT button.
¢ The EDIT mode is canceled.
If you press the MULTI COMMAND button, these remote control signals
are transmitted in the order programmed, so if CONTROL IN/OUT is
connected (refer to page 16), and if remote control signals can reach
both the receiver and CD player sensor windows, power to the receiver
switches on, the input selector switches to CD, and the CD player starts
playing. (When the CD piayer's power cord is plugged into the receiver's
switched AC OUTLET.)
NOTE:
After pressing the seventh command, the MULTI-EDIT mode is
registered automatically (The VCR 1, VCR 2, and TV CONTROL MODE
buttons flash in sequence}, but the EDIT mode is not canceled. To
cancel the EDIT mode, press the EDIT button.
After memorizing six or less commands, if you cancel the EDIT mode
without pressing the MULT! COMMAND button again, all the
registered commands are cleared, leaving the previous commands as
they were.
if a button is for transmission, even if it is not an operation button in
the selected CONTROL MODE, registration is still possible. (Buttons
such as the VCR 7 }a<t.)
In this case, during signal transmission, the CONTROL MODE button
momentarily lights, but the remote control code is not transmitted.
If the component to be operated is installed at a distance, if there is
an obstacle between a specific component sensor window and the
remote control, or if component operation speeds are very different,
MULTI-COMMAND operation may be incorrect. When repeating
operations, first return to the initial settings for each component. For
operations such as power ON/OFF, if components are switched ON,
they can be switched OFF by transmitting a signal.
RETURNING TO THE INITIAL SETTINGS
Initialization of particular CONTROL MODES
1,
2.
Remove the battery compartment cover.
While pressing the M.CLEAR button inside the cover, press the
button for the CONTROL MODE (for example VCR 1) you want
to initialize.
¢ For example, if you initialize VCR 1 using the method mentioned
above, the CONTROL MODE button lights for about one second,
and the VCR 1 operation buttons are initialized.
M.CLEAR button
Initializing the entire memory
1.
2.
Remove the battery compartment cover.
While pressing the M.CLEAR button inside the cover, press the
RESET button.
* Do not release the M.CLEAR button before releasing the RESET
button. While pressing the M.CLEAR button, press the RESET
button, and quickly release.
Initialization is not possible if the buttons are pressed in the reverse
order.
© All the CONTROL MODE operation buttons are initialized, and data
in the MULTI COMMAND button is cleared.
M.CLEAR button
39
<ARB1421>