Table of Contents
Advertisement
REMOTE CONTROL OPERATION
(TV)
(VCR)
Button functions are the same as Pioneer's unified remote control code
functions, so refer to page 34 concerning TV functions, and page 33
concerning VCR functions.
NOTE:
© /f there is a remote control operation button for a function your TV
or VCR does not have, operation is not possible.
© Depending on the kind of remote control signal, it may not be possible
to preset TV FUNC button for TV operation.
© The Pioneer remote control code remains in the TV DISP. 11, and 12
buttons, and the VCR DISP 7 to 12 buttons without presetting.
{Procedure for presetting]
1. Press the EDIT button to switch to the EDIT mode.
2. Press one of the CONTROL MODE buttons (VCR 1, VCR 2, or TV).
3. Press one of the buttons 1 to 12.
© One kind of code is preset.
* To continue presetting, repeat operation procedures 2 and 3.
4. Press the EDIT button.
© The EDIT mode is canceled.
5. Confirm that the component (TV or VCR) can be operated by the
preset code.
If operation is not possible, repeat the procedures from step 2, and
press a different number button (1—12) at step 3 to search for a
preset code that enables operation. Refer to the diagram on this
page.
{Operation example]
As a preset example, here is an explanation of how to preset in VCR 1.
1. Press the EDIT button.
© The VCR 1, VCR 2, and TV CONTROL MODE buttons flash in
sequence.
2. Press the VCR 1 CONTROL MODE button.
* Only the VCR 1 button flashes.
3. Press one of the buttons 1 to 12.
¢ For example, if you press button 1, the remote control signal
format selected with VCR 1 operation button 1 is preset.
The CONTROL MODE buttons light in sequence (indicating that
registration has been completed), and then the VCR 1, VCR 2,
and TV buttons flash in sequence. (Returning to the condition in
procedure 1.)
¢ To continue presetting for VCR 2 and TV, repeat operation
procedures 2 and 3.
4. Press the EDIT button.
© The EDIT mode is canceled.
38
<ARB1421>
5. Point the remote control at the sensor window of the VCR you want
to operate and press an operation button to confirm that operation
is possible.
.
® If operation is possible, presetting has been completed.
© If operation is not possible, repeat operations from step 2, selecting
a different number button (1 to 12) at step 3.
if there is a button among buttons 1 to 12 that cannot operate, press
the EDIT button once more to cancel: the EDIT mode, and memorize
in the LEARN mode.
NOTE:
© After pressing the EDIT button, if you do not press a button within
about one minute, the EDIT mode is canceled.
° After memorizing in the LEARN mode, if you preset operations under
specified buttons, Signals memorized in the LEARN mode are cleared.
Remote control codes of other manufacturers preset in
the preset
The following table shows the PRESET MODE buttons (1 to 12) used
to call up the remote control codes of other manufacturers. Preset remote
control signals in the table, however, may not always enable operation.
Numbers in parenthesis indicate a reduced possibility of operation.
1, (10)
(1), (6)
3
(3), (4)
8, (11), (1)
(1), (8)
4
5
HITACHI
6, (10)
PHILIPS
Jvc
PANASONIC
MITSUBISHI
9, (10)
SANYO
-
SHARP
(2)
GOLD STAR
(10)
(11)
MAGNAVOX
(7), (10), (12)
(8), (9}
SYLVANIA
(7), (10), (12)
(8), (9)
QUASER
8.
8
FISHER
_
12, (10)
WARD'S
(2), (7), (10), (11)
(2)
10, (12)
2
Advertisement
Table of Contents
