Table of Contents
Advertisement
REAR PANEL FACILITIES
@ PRE OUT jacks
[FRONT AMP]
When a separate power amplifier is used to drive the front speakers,
connect the power amplifier to these jacks.
{CENTER AMP]
When a separate power amplifier is used to drive the surround center
speaker, connect the power amplifier to this jack.
[REAR AMP]
When a separate power amplifier is used to drive the rear speakers,
connect the power amplifier to these jacks.
@ CENTER SPEAKER terminals
Connect the center speaker to these terminals.
The VSX-D702S has two sets of center speaker terminals so dual center
speakers can be used. (See page 11)
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
@REAR SPEAKERS terminals
Connect the rear speakers to these terminals.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use rear speakers of impedance 8 2 —
16 2.
FRONT SPEAKERS terminals
A: Connect to the first set of speakers.
B: Connect to the second set of speakers.
Speaker lead wire preparation and connection.
NOTE:
Do not allow any of the cord's conductors to protrude from the terminals
or touch any other conductors. Malfunctioning or breakdowns may
occur when conductors come into contact with each other.
Use speakers of impedance 8 2 — 16 0.
@ PHONO input jacks
Connect to the output cables from a turntable.
@2 GND terminal
Connect the turntable ground lead to this terminal.
@ CD input jacks
Connect to the output jacks of a compact disc player.
TV jacks (input)
Use these jacks if you wish to connect a TV tuner with both video and
audio outputs.
[VIDEO IN]
Connect the TV tuner's VIDEO OUTPUT to this jack.
[AUDIO IN (L, R)]
Connect the TV tuner's AUDIO OUTPUT to these jacks.
@) LD jacks
[VIDEO IN]
When watching the video image from an LD player, connect its VIDEO
OUTPUT jacks here.
[AUDIO IN (L, R)]
When playing back the audio channel from an LD player, connect its
AUDIO OUTPUT jacks here.
16
<ARB1421>
@ $ (connector) video jacks (VSX-D702S only)
When used in conjunction with a VCR, Video disc player (LaserDisc
player), or TV monitor equipped with S video jacks, connect to these
jacks. (See pages 7, 9)
@ CENTER SPEAKER SELECTOR Switch
This switch changes the speaker impedance for when only one center
speaker is connected, or two speakers are connected.
When only one speaker is'connected:
Be sure to set the switch to "I ONLY'' (down side), and always connect
a speaker with an impedance of 8 2 — 16 © to the | terminal.
When two speakers are connected:
Be sure to set the switch to "I + II'' (up side), and always use speakers
with an impedance of
42 — 16 Q.
NOTE:
Switch the CENTER SPEAKER
SELECTOR
when
the unit power
supply is at STANDBY. Do not switch the selector when the power
supply is at ON.
CONTROL IN/OUT jacks
IN:
Connect this jack to other Pioneer components (main unit or
remote contro! unit) when using those components to control
this unit.
OUT:
Connect this jack to other Pioneer components when using the
remote control of this unit.to control the other components.
NOTE:
The receiver's remote sensor does not function when a plug is inserted
in INjack. To operate, point the remote control unit at the remote sensor
on the component to which the receiver's IN jack is connected.
When using
1)
conven
the MR-100
mel
Je
MR-100
Cl
ex
ZVese
Receiver
f—
Pioneer component
bearing the {i mark.
Remote
control
To the CONTROL IN
MEME
Remote
jack of the Pioneer
control unit
component bearing
the fi] mark.
Advertisement
Table of Contents
