Pioneer VSX-D6025 Operating Instructions Manual page 19

FRONT PANEL FACILITIES
@ SCAN button
Operate when the INPUT SELECTOR is set to TUNER. Station
frequencies assigned to the STATION CALL buttons are tuned in, one
after another, beginning with the current station no., for approximately
5 seconds each. The display section SCAN indicator will light. Press
the button again and the tuner remains tuned in to the station playing
when the button was pressed the second time.
Station frequencies not assigned to station numbers in the memory are.
skipped.
When you have selected a CUSTOM MEMORY genre, memory scan
is performed on the stations in that genre.
(8) MPX MODE button
Use to select the auto stereo mode or monaural mode when listening
to FM broadcasts. The monaural mode has been selected when the
FM MONDO indicator in the display section is lit. ©
Auto stereo mode:
Normally, leave in this mode for reception. When a stereo FM broadcast
is received, it will be automatically reproduced in stereo.
Monaural mode: :
When receiving distant stations or stations with weak broadcast signals,
the input signal may be weak, thus resulting in increased noise during
FM stereo broadcasts. In this event, setting the receiver to the monaural
mode will reduce the noise. In this case, however, FM stereo broadcasts
will be reproduced in monaural sound.
NOTE:
This button has no effect on reception of AM broadcasts.
@) Tuning buttons
TUNING MODE tuning selector button: (Pages 22, 23)
Use to select the tuning mode. To select the AUTO tuning mode, press
this button to light the AUTO TUNING indicator in the display section.
To select the MANUAL tuning mode, switch off the AUTO TUNING
indicator.
AUTO tuning
When the — or + TUNING button is pressed, the receiver automatically
_ scans the broadcast station frequencies. When a broadcast is detected,
the.scanning stops at that frequency.
NOTE:
Pressing the TUNING button (— or +} while scanning is taking place
causes scanning to stop.
MANUAL tuning
This lets you manually tune to particular broadcast frequencies. Each
press of the + or — button raises or lowers the frequency by one tuning
step. For continuous scanning, keep the button pressed, then release
it to stop scanning.
DIRECT ACCESS tuning button: (Page 22)
When this button is pressed, the STATION CALL buttons function as
ten-key number buttons for direct input of the desired reception
frequency. Press again to cancel this mode.
If the input station falls outside of the receiver's tuning range, the display
section will display a message: '"UPPER"' if the frequency is too high
and "LOWER" if it is too low. :
HITS (Hyper Intelligent Tuning System) button: (Page 24)
Press this button, and search automatically begins up and down the
frequency for stations that can be received. When a station that can
be received is found, the search operation stops.
@ STATION CALL buttons
Up to 30 FM or AM stations can be preset at random.
These buttons are used to preset 'and recali desired broadcasting
stations, FM AUTO/MONO mode.
NOTE: :
Pressing a STATION CALL button will select TUNER as the source,
regardless of what other listening source or function was selected.
They are also used when performing direct access tuning.
@) SIMULATED STEREO button
Press to produce a simulated stereo effect when listening to monaural
sources (for example, normal AM or TV broadcasts).
"SIMULATED STEREO" appears on the display section.
NOTE:
© This effect is not produced through the rear speakers.
* Use with the SURROUND MODE in the OFF.
@ SURROUND MODE selector buttons
See page 5 "SURROUND EFFECT'.
@ BALANCE buttons
Use them to adjust the sound volume balance between left and right
speakers.
L: Press to decrease the sound on the right side.
R: Press to decrease the sound on thé left side.
Press L and R together to bring the volume balance back to center.
NOTE:
The left-right sound volume balance cannot be adjusted on the rear
speakers.
@ TREBLE control buttons
Use to adjust the high-frequency level. Press the + button to increase
the high-frequency level, and the — button to decrease it.
The TONE indicator appears on the display section.
When both buttons (—, +) of the TREBLE control are pressed
simultaneously, the treble response will be set to the flat (normal)
condition.
@ BASS control buttons
Use to adjust the low-frequency level. Press the + button to increase
the low-frequency level, and the — button to decrease it.
The TONE indicator appears on the display section.
When both buttons (—, +) of the BASS control are pressed
simultaneously, the bass response will be set to the flat (normal)
condition.
DSP EFFECT/DELAY TIME buttons
[DSP EFFECT)
When using a surround mode other than DOLBY PRO LOGIC
SURROUND, 10-step adjustment of the effect level is possible from
10 to 100.
{DELAY TIME]
Operates when the DOLBY PRO LOGIC SURROUND mode is ON.
Switches to surround delay time in 8 steps. For DOLBY PRO LOGIC
SURROUND, 20 ms is standard.
Changes in 2 ms steps.
16 ms +> 18 ms <+--- ++28 ms ++30 ms
19
<ARB1421>