Table of Contents
Advertisement
You can memorize receiver settings, and recall at the touch of a button.
Two memory buttons are available.
If you connect a component bearing the Pioneer ff] mark, such as a
CD player, to the CONTROL OUT jack on the rear panel, signals can
also be transmitted to automatically switch on power and start play of
that component.
NOTE:
With some components, even if they bear the | mark, power cannot
be switched on and off by remote control.
[Operating Memory]
1. Select the settings on the receiver you want to memorize.
2. Press the MEMORY button.
¢ After the "AUTO SOURCE CONTROL" indication has scrolled in
the display, "MEMORY"
appears and flashes.
3. Press the AUTO SOURCE CONTROL button (1 or 2) you want to
use for memorizing.
2 MEMORY
3 AUTO SOURCE CONTROL (1, 2)
Example:
Using the AUTO SOURCE CONTROL 1 button to memorize settings
to start play on a CD player connected to the receiver's CONTROL OUT
jack.
1. Set the receiver INPUT SELECTOR to CD.
2. Adjust tone, surround, and other parameters to the settings you
want to memorize.
3. Set the volume to the level you want to memorize.
4. Press the MEMORY button.
5. Press the AUTO SOURCE CONTROL 1 button.
[Recalling]
Press the AUTO SOURCE CONTROL button (1 or 2) for the settings
you want to recall.
Remote contro! AUTO SOURCE CONTROL buttons (1 or 2) can aiso
be used to recall settings.
"AUTO SOURCE CONTROL 1 (or 2)'' is scroll displayed. After the last
indication, such as 'PLAY CD"' has been scroll displayed, the display
switches to function indications.
In the case of the example, the following operations are performed.
@ Press the AUTO SOURCE CONTROL 1 button.
@ Power to the receiver switches ON, the INPUT SELECT OR selects
CD, settings for such parameters as surround, and tone are called
up, and power to the CD player is switched ON.
@® Play starts on the CD player. "
:
@® Volume level is raised by the MASTER VOLUME on the receiver.
NOTE:
© Memorized volume level and recall volume level may differ by a small
amount.
© /f volume is near minimum level when memorized, volume may not
rise when the setting is recalled.
NOTE:
© Since the power ON and play signals for components bearing the
mark called by Auto source control are output through this unit's
CONTROL OUT jack, be sure to connect the control cord (refer to
page 16).
,
© With some components, even if they bear the [iqi| mark, power cannot
be switched on and off by remote control. If this is the case, by
connecting the other unit's power cord to this unit's SWITCHED AC
OUTLET, and leaving the other unit's power switch ON, power
switching will depend on whether this unit is on or off.
© Volume level can not be raised above the center setting.
e AUTO SOURCE CONTROL memory stores the receiver settings at
that point in time; it does not memorize STATION CALL numbers
(1-30), CUSTOM
MEMORY,
or ACOUSTIC MEMORY
(A—E,
LOUDNESS, FLAT).
© During the operation of
AUTO SOURCE CONTROL, other components
are also being controlled, so do not perform other operations until it
is finished.
With auto source control, power ON/OFF signals and play signals are
output from the CONTROL OUT jack at the times shown in the following
chart.
Function at the time
of memorizing
PHONO
TUNER
cD
Yes
TAPE 1
Yes
Yes
POWER signal
PLAY signal
Yes
Yes
Yes
Sar
mae
|
|
VeeMDP TV wh eee a
Yes (TV FUNC "TV"')
Yes (VCR PLAY, TV
FUNC "'LD"')
LD
TV
VIDEO
Yes (VCR, TV)
Example of AUTO SOURCE CONTROL 1, 2 memory.
AUTO SOURCE | \. 06 | input
sel
CONTROL
ume
Nput
selector
DOLBY PRO LOGIC
oe
eee
| SURROUND
ere
eae Eee
Surround mode
29
<ARB1421>
Advertisement
Table of Contents
