Parameter List (By Function Group Number) - Mitsubishi Electric FR-CS82S-025 Instruction Manual

5.1.3

Parameter list (by function group number)

 E: Environment setting
parameters
Parameters for the inverter operating environment.
Pr.
Pr.
group
Parameter for manufacturer setting. Do not
E000 168
set.
Parameter for manufacturer setting. Do not
E001 169
set.
Parameter for manufacturer setting. Do not
E023 269
set.
Parameter for manufacturer setting. Do not
E080 168
set.
Parameter for manufacturer setting. Do not
E081 169
set.
E100 75 Reset selection
E101 75 Disconnected PU detection
E102 75 PU stop selection
E103 145 PU display language selection
E104 990 PU buzzer control
E105 991 PU contrast adjustment
Frequency setting / key lock
E200 161
operation selection
RUN key rotation direction
E202 40
selection
Regenerative function
E300 30
selection
E400 77 Parameter write selection
E410 296 Password lock level
E411 297 Password lock/unlock
Parameter for manufacturer setting. Do not
E415 520
set.
E600 72 PWM frequency selection
E601 240 Soft-PWM operation selection
 F: Parameters for the settings of
the acceleration/deceleration time
and the acceleration/deceleration
pattern
Parameters for the motor
characteristics.
Pr.
Pr.
group
Acceleration/deceleration
F000 20
reference frequency
Jog acceleration/deceleration
F002 16
time
F003 611 Acceleration time at a restart
F010 7 Acceleration time
F011 8 Deceleration time
Second acceleration/
F020 44
deceleration time
F021 45 Second deceleration time
Acceleration/deceleration
F100 29
pattern selection
F101 59 Remote function selection
F102 13 Starting frequency
Refer
Name
to page
85
85
85
87
87
88
88
88
159
89
90
90
92
92
acceleration/deceleration
Refer
Name
to page
93
108
159
93
93
93
93
95
96
99
 D: Parameters for the setting of
operation command and
frequency command
Parameters for setting the command source to the inverter,
and the motor driving frequency and torque.
Pr.
Pr.
group
D000 79 Operation mode selection
Communication startup mode
D001 340
selection
Communication operation
D010 338
command source
Communication speed
D011 339
command source
PU mode operation command
D013 551
source selection
Reverse rotation prevention
D020 78
selection
D200 15 Jog frequency
Multi-speed setting (high
D301 4
speed)
Multi-speed setting (middle
D302 5
speed)
Multi-speed setting (low
D303 6
speed)
D304 to Multi-speed setting (speed 4 to
24 to 27
D307 speed 7)
D308 to 232 to Multi-speed setting (speed 8 to
D315 239 speed 15)
 H: Protective function parameter
Parameters to protect the motor and the inverter.
Pr.
Pr.
group
Electronic thermal
H000 9
O/L relay
Earth (ground) fault detection
H101 249
at start
Inverter output fault detection
H104 631
enable/disable selection
Undervoltage detection
H105 598
enable/disable selection
Output phase loss protection
H200 251
selection
Input phase loss protection
H201 872
selection
H300 65 Retry selection
Number of retries at fault
H301 67
occurrence
H302 68 Retry waiting time
H303 69 Retry count display erase
H400 1 Maximum frequency
H401 2 Minimum frequency
High speed maximum
H402 18
frequency
H420 31 Frequency jump 1A
H421 32 Frequency jump 1B
Refer
Name
to page
100,
104
104
105
105
105
108
108
109
109
109
109
109
Refer
Name
to page
112,
147
114
114
115
115
115
115
115
115
115
117
117
117
118
118
81
5. PARAMETERS
5.1 Parameter list
4
2
3
4
5
6
7
8
9
10