Video On/Off; Display Mode; Selecting Analog Audio Input Or Digital Audio Input; Recording An Analog Source - Marantz SR9600U User Manual

VIDEO ON/OFF

When no video signal is connected to the SR9600
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
setting the video off mode.
1.
To set the video off mode, tap the A/V Amp
and press the page up button until page 5/8 is
displayed.
Tap the Video off on the remote control unit.
"V-OFF" indicator will be illuminated when this
function is activated.
wed Jun 01 4:40 pm
5/8 A/V Amp
Mode
1.
2.
To cancel the Video Off mode, tap the Video
off on the remote control unit again.
56
SR9600U DFU̲01̲ENG 4̲4 Page 56
All manuals and user guides at all-guides.com

DISPLAY MODE

You can select the display mode for the front panel
display on the SR9600.
1.
To select this mode, press the DISPLAY
button on the front panel or tap the Display on
the remote control.
wed Jun 01
1.
5/8
1.
AV SURROUND RECEIVER SR9600 VER SR9600
VOLUME
INPUT SELECTOR
DOWN
PURE DIRECT PURE DIRECT THX THX DOWN DOWN TUNING TUNING UP UP BAND BAND F/P F/P
SURROUND SURROUND MULTI MULTI
MODE MODE AUTO AUTO MULTI MULTI SPEAKER SPEAKER AUTO TUNE AUTO TUNE T-MODE T-MODE MEMORY MEMORY CLEAR CLEAR
7.1CH INPUT 7.1CH INPUT DISPLAY DISPLAY
SPEAKERS SPEAKERS
PURE DIRECT PURE DIRECT THX THX MRAC MRAC A/B A/B
STANDBY ENTER ENTER
MENU MENU EXIT EXIT
AUX 1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO
POWER ON/STANDBY PHONES MIC MIC
When this button is pressed, the Display
mode is switched in the following sequence:
Normal mode → Level Meter mode → Auto
Display Off mode → Display Off mode →
Normal mode → ....
Normal mode:
Displays the selected component.
Level meter mode:
Displays the current output level of up to 7.1
channels as a bar graph.
MULTI A . B . SPK A . B
SPKR PEAK ATT
SLEEP V-OFF Re-EQ NIGHT
DVD:AT > HDMI.2
S S
B S S S B
L L L C R W R R
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to
off after about 3 seconds. When changing the
volume, it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the "DISP" indicator will be illuminated on
the front panel display when the Display Off
mode is selected.
• Only SBL is displayed in the Level Meter mode if
"SURR.B" on the SPEAKER SIZE menu in the
SETUP MENU is set to 1 channel (1CH).
SELECTING ANALOG AUDIO INPUT
OR DIGITAL AUDIO INPUT
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source.
1.
Tap the A/V Amp and press the page up
4:40 button until page 5/8 is displayed. Tap the A/D
pm
A/V Amp
on the remote control unit.
Mode
wed Jun 01
5/8 A/V Amp
UP
R
1.
When the A/D is tapped, the input mode is
switched in the following sequence:
Auto → i.LINK → HDMI → Digital→ Analog
→ Auto ....
Auto mode:
The types of signals being input to the digital
and analog input jacks for the selected input
source are detected automatically.
If no digital signal is being input, the analog input
HDMI DIGITAL
DIGITAL EX
jacks are selected automatically.
i.LINK mode:
L C R
LFE
dB i.LINK mode can be selected only when an
+18.0 SL S SR
i.LINK device has been assigned as an input
source.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
Digital mode:
The input signal is fixed to an assigned digital
input terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select "1.
INPUT SETUP" from the MAIN MENU. (See page
32)
05.4.27, 5:48 PM

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source
selected for listening through the SR9600 is sent to
the record outputs.
This means that any program you are watching or
listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR1 OUT, and VCR2/DVD-R
OUT in the Record mode.
To record the input source signal you are
4:40
pm
currently watching or listening to
Mode
1.
Select the input source to record by turning
the INPUT SELECTOR knob on the front
panel or simply select a source from among
the Source Select screen on page 1/8 on the
remote control unit.
The input source is now selected and you may
watch or listen to it as desired.
1.
AV SURROUND RECEIVER SR9600 AV SURROUND RECEIVER SR9600
INPUT SELECTOR INPUT SELECTOR
STANDBY STANDBY
POWER ON/STANDBY POWER ON/STANDBY PHONES PHONES
2.
The currently selected input source signal is
output to TAPE OUT, CD-R/MD OUT, VCR1
OUT, and VCR2/DVD-R OUT for recording.
3.
Start recording to the recording component as
desired.
Adobe PageMaker 6.5J/PPC
wed Jun 01 4:40
pm
1/8 A/V Amp
Source Select
VOLUME
DOWN UP
PURE DIRECT PURE DIRECT THX THX DOWN TUNING UP BAND F/P
1.
SURROUND SURROUND MULTI
MODE MODE AUTO AUTO MU MULTI SPEAKER AUTO TUNE T-MODE MEMORY CLEAR
7.1CH INPUT DISPLAY
SPEAKERS
PURE DIRECT PURE DIRECT THX THX MRAC A/B
ENTER
MENU EXIT
AUX 1 INPUT
MIC DIGITAL S-VIDEO VIDEO L AUDIO R