Table of Contents
Advertisement
Unit Assembly Prior to Installation
Unit Assembly Prior to Installation
Before you start
Before you Start - Removing the Unit from the
Removing the unit from the pallet
Pallet
Unit Assembly Prior to Installation
Before you start
Remove the screws securing the unit to the pallet
Removing the unit from the pallet
Unit Assembly Prior to Installation
Remove the screws securing the unit to the pallet
Before you start
Due to the CV50E's size and weight (480 pounds shipping weight),
Removing the unit from the pallet
lifting and moving the unit requires 4 people.
Due to the size and weight (480 pounds shipping weight) of the CV60E--lifting
Remove the screws securing the unit to the pallet
and moving the unit will require 4 people.
Due to the size and weight (480 pounds shipping weight) of the CV60E--lifting
Place a length of 2 x 4 long enough to get a solid grip on each side
and moving the unit will require 4 people.
Place a length (long enough to get a solid grip on each side) of 2 x 4 under
Remove the screws securing the unit to the pallet
under each handle.
the handle on each side.
Place a length (long enough to get a solid grip on each side) of 2 x 4 under
Due to the size and weight (480 pounds shipping weight) of the CV60E--lifting
the handle on each side.
Lift and move the unit carefully.
and moving the unit will require 4 people.
Lift and move the unit carefully.
Lift and move the unit carefully.
Place a length (long enough to get a solid grip on each side) of 2 x 4 under
Note: When in the unit is in position, the handles can be detached
Note : When in position, the handles may be removed from the unit by removing
the handle on each side.
Note : When in position, the handles may be removed from the unit by removing
by removing 6 screws from each. Ensure the screws are replaced
6 screws on each handle. Ensure that when the handles are removed that the
6 screws on each handle. Ensure that when the handles are removed that the
screws are put back into place in all 12 holes locations where the handle had
Lift and move the unit carefully.
in the holes they were removed from (6 per side). The handles are
screws are put back into place in all 12 holes locations where the handle had
been previously (6 per side). The handles can be recycled.
been previously (6 per side). The handles can be recycled.
recyclable.
Note : When in position, the handles may be removed from the unit by removing
6 screws on each handle. Ensure that when the handles are removed that the
Side Standoff Assembly
screws are put back into place in all 12 holes locations where the handle had
been previously (6 per side). The handles can be recycled.
The CV50E has 4 standoffs (2 on each side) that you must assemble
Side stando assembly CV60E
before installation. The standoffs are shipped in a flat position. Fold
the standoffs and install them by sliding the 2 tabs into the slots
The CV60E has 4 stando s, 2 on each side that need assembly before installing.
Side stando assembly CV60E
on the unit. Bend the tabs and secure the opposite end of each
The stando s are shipped in a flat position -- fold the stando and install the
tooltip
stando onto the unit by sliding the 2 tabs into the slots on the unit. Bend the
standoff with one screw.
Side stando assembly CV60E
The CV60E has 4 stando s, 2 on each side that need assembly before installing.
tabs to secure. Secure opposite end of the stando with one screw.
The stando s are shipped in a flat position -- fold the stando and install the
The CV60E has 4 stando s, 2 on each side that need assembly before installing.
stando onto the unit by sliding the 2 tabs into the slots on the unit. Bend the
The stando s are shipped in a flat position -- fold the stando and install the
stando onto the unit by sliding the 2 tabs into the slots on the unit. Bend the
tabs to secure. Secure opposite end of the stando with one screw.
tabs to secure. Secure opposite end of the stando with one screw.
CV60E
Rear Stando s
Rear Standoffs
The 2 top rear stando s are designed so that screws can be used to secure
the appliance to the rear wall if needed. Studs must be in this location if
The 2 top rear stadoffs are designed so that screws can be used
choosing to screw this into studs.
CV60E
Rear Stando s
to secure the appliance to the rear wall if needed. Studs myst be
CV60E
Rear Stando s
in place for this operation.
The 2 top rear stando s are designed so that screws can be used to secure
Leveling Legs
the appliance to the rear wall if needed. Studs must be in this location if
choosing to screw this into studs.
The 2 top rear stando s are designed so that screws can be used to secure
There are four levelling legs - two on each side that can be adjusted (with the
the appliance to the rear wall if needed. Studs must be in this location if
Leveling Legs
supplied tool--found in the manual package) if required.
choosing to screw this into studs.
Leveling Legs
There are four levelling legs, two on each side, that can be adjusted
with the tool found in the manual package.
There are four levelling legs - two on each side that can be adjusted (with the
supplied tool--found in the manual package) if required.
Leveling Legs
There are four levelling legs - two on each side that can be adjusted (with the
supplied tool--found in the manual package) if required.
tooltip
tooltip
Standoffs
Leveling legs
installation
Leveling legs
Leveling legs
City Series CV50E |
Top Rear Standoffs
31
Advertisement
Table of Contents
