Stiga CS 100 Li 20 A Operator's Manual page 160

preventive safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the reach
of children and do not allow persons
unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of
moving parts, breakage of parts and
any other condition that may affect the
power tool's operation. If damaged, have
the power tool repaired before use. Many
accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces
dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do
not allow for safe handling and control of the
tool in unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified
by the manufacturer. A charger that is
suitable for one type of battery pack
may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep it
away from other metal objects, like paper
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact.
If contact accidentally occurs, flush with
water. If liquid contacts eyes, additionally
seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e) Do not use a battery pack or tool that
is damaged
or modified
or modified. Damaged
batteries may
unpredictable behaviour resulting in fire,
explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature. Exposure to fire
or temperature above 130 °C may cause
explosion. NOTE The temperature „130
°C" can be replaced by the temperature
„265 °F".
g) Follow all charging instructions and do not
charge the battery pack or tool outside
the temperature range specified in the
instructions. Charging improperly or at
temperatures outside the specified range
may damage the battery and increase the
risk of fire.
6) Service
a) Have your power tool serviced by a
qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
b) Never service damaged battery packs.
Service of battery packs should only
be performed by the manufacturer or
authorized service providers.
2.2 SPECIFIC SAFETY RULES
FOR CHAINSAWS AND
ELECTRIC CHAINSAWS.
a) Keep all parts of the body away from the
saw chain when the chain saw is running
Before you start the chain saw, make sure
the saw chain is not contacting anything.
A moment of inattention while operating
chain saws may cause entanglement of your
clothing or body with the saw chain.
b) Always hold the chain saw with your right
hand on the rear handle and your left hand
on the front handle. Holding the chain saw
with a reversed hand configuration increases
the risk of personal injury and should never be
done.
c) Hold the chaisaw by insulated gripping
surfaces only, because the chainsaw
may contact hidden wiring. Saw chains
contacting a "live" wire may make exposed
metal parts of the chain saw "live" and could
give the operator an electric shock
d) Wear safety glasses protection. Further
protective equipment for hearing, head,
hands, legs and feet is recommended
The wearing of protective clothing will reduce
accidents caused by hurled workpieces and
accidental contact with the toothed chain.
e) Do not operate a chain saw in a tree, on
exhibit
a ladder, from a rooftop, or any unstable
EN - 3