Customer Service; Charging The Battery - Peg-Perego Polaris Sportsman PRO Citrus Use And Care Manual

CUSTOMER SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
Refer to the last illustration in this manual to find
the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
ASSEMBLY MUST ONLY BE CARRIED OUT BY
ADULTS. TAKE CARE WHEN REMOVING THE
VEHICLE FROM ITS PACKAGING. ALL THE
SCREWS AND SMALL PARTS ARE CONTAINED IN
A BAG INSIDE THE PACKAGING. THE BATTERY
MAY ALREADY BE FITTED INSIDE THE ITEM.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while assembling
the toy, given the risks caused by small parts
(ingestion hazard) and the plastic bags that contain
them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Lift both rear shock absorbers, and line them up
with the openings in the chassis.
2 • To secure the shock absorbers to the frame,
insert the pins into the top holes of the shock
absorbers, pushing them in until fully inserted.
3 • Remove the protective caps from the steering
arms.
4 • Insert a large washer onto both steering arms.
5 • Insert the bushes into the inside of the wheels,
paying attention to the direction of the tread, as
shown in the figure.
6 • Insert one of the two wheels, paying attention to
the pattern of the tread, which must be facing in
the direction shown in the figure.
7 • Insert a small washer and the nut.
8 • Fix the nut securely using the key provided.
Repeat for the other front wheel.
9 • Remove the protections from the rear axle.
10 • Insert the axle into the rear part of the vehicle as
shown in the figure. N.B.: check there are 2 metal
tubes present inside the gear motors.
11 • Position the drivers inside the remaining wheels.
12 • Assemble the wheel onto the axle with the driver
facing the vehicle. Pay attention to the direction
of the tread, as shown in the figure.
13 • Insert 1 small washer and 1 plastic washer onto
the axle.
14 • Fasten the wheel, tightening one of the four nuts
supplied with the spanner provided.
• Repeat the fitting operations for the other rear
wheel. Important: carry out the operations while
holding the axle still on the opposite side with
the help of the second spanner provided.
15 • Snap fit the four hub covers onto the wheels.
16 • Turn the seat lock to the "unlock" position
shown in the diagram, and lift the seat. NOTE:
Seat has a lock and unlock position.
17 • Insert the seat cover by sliding it along its entire
length, keeping the elastic at the bottom and
hooking the 6 retaining points, as shown in the
figure.
18 • Attach seat by inserting black tabs on seat into
slots on body. Then rotate down into place. Close
the seat by turning the red pin.
19 • Attach black radiator piece by first inserting tabs
into corresponding rectangular slots (a). Then
press firmly on the upper tabs (b) so that they
fully engage into their slots.
20 • Position front rack onto supports as shown in
figure and secure with 4 screws provided.
21 • Apply radiator decal.
22 • Insert the two brackets into the openings on the
radiator, as shown in the figure.
23 • Attach charcoal front grill to front rack by lining
up connection points and snapping into place.
24 • Attach the silver front brush guard by lining up
connection points and snapping into place.
25 • Fasten the grill with the 2 screws.
26 • Attach the two chrome decals to the headlight
positions on the grill.
27 • Snap the two headlights onto the grill.
28 • Attach the chrome decal to the chassis, as shown
in the figure.
29 • Snap the taillight into place by inserting it from
the top.
30 • To attach folding extra seatback, insert one of the
posts into the rear rack.
31 • Position seatback with handle down and slide peg
into hole on post.
32 • Slide second post onto peg on seatback (a) and
then press post down into position (b).
33 • Folding extra seatback with posts in place.
34 • While holding seatback and posts in position,
fasten posts using screws provided.
35 • Connect rear rail to rear rack by inserting tabs
on rail into slots on rack, rotating into place and
fastening using screws provided.
36• Position rear rack onto supports as shown in
figure and secure with 4 screws provided.
37 • Snap the toy gas cap into place on the vehicle.
38 • Slip the two handguards onto the handlebars,
lining up the holes in the handguards with the
holes in the handlebars.
39 • Fasten the hand guards with the two screws.
40 • Slip the handgrips onto the handlebars as shown.
41 • Insert the handlebar into the vehicle by
connecting the 2 cables of the electrical system,
as shown in the figure.
42 • Turn the seat lock to the "unlock" position
shown in the diagram, and lift the seat. NOTE:
Seat has a lock and unlock position.
43 • Connect wiring system of the vehicle (plug A) to
the battery (plug B).
44 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.
FEATURES AND USE OF THE VEHICLE
45 • 1- START/STOP: when pressed, this button lights
up and enables all the vehicle's functions (START).
When pressed again, it turns off and disables all
the vehicle's functions (STOP).
2 - FM RADIO:
A - USB port
B - SD CARD slot
C - AUX input
D - Selection buttons: when pressed individually,
these buttons allow you to select tracks and
radio frequencies.
When pressed several times simultaneously, they
allow you to shift from one mode to another, as
displayed (USB, SD, AUX).
E - volume buttons: turn the volume down
completely to turn the radio off. The word OFF
will be displayed. Press the "volume up" button to
turn it on again.
3 - HORN: press it to activate it.
4 - LED indicators on the dashboard:
- ENGINE: a steady red LED indicates engine
overload. Release the pedal. Wait 10 seconds for
the vehicle to be ready for use again.
- BATTERY: a blinking orange LED means that the
battery is low. When this happens, the vehicle
enters "POWER SAVING" mode (low speed, no
lights and sounds).
The blinking LED becomes steady when the
battery is flat. At that point, the vehicle stops
working until the battery is charged. If you need
to move the vehicle while the battery is flat, you
can release the brake by pushing down the
accelerator. This way, you can push it manually.
46 • ACCELERATOR PEDAL and ELECTRIC BRAKE:
lift the foot from the pedal to engage the brake
automatically.
The vehicle will enter standby mode (OFF) after
10 minutes of inactivity. If the START button is
activated, the vehicle will resume its functions by
pressing the pedal.
47 • GEAR SHIFT LEVER: The vehicle has three
speeds. ATTENTION: When the vehicle is first
removed from the packing, it only runs in first
gear (1) and reverse (R). To use the second gear
(2), proceed as follows:
48 • Screw down the second gear unit, as shown in
the following figure.
49 • 1-R: The second gear unit protrudes from the
chassis, preventing the gearshift lever from
moving down to the second gear. 1-2-R: The
second gear unit is completely screwed into the
chassis, and the gearshift lever can be lowered.
50 • To raise and lower the folding extra seatback, pull
up on the handle on the back of the seatback.
51 • ACCESSORY: trailer to attach to the vehicle (sold
separately).
REPLACING THE BATTERY
PLEASE NOTE: THE PICTURES OF THE BATTERIES
ARE FOR ILLUSTRATIVE PURPOSES ONLY. YOUR
BATTERY MAY BE DIFFERENT FROM THE MODEL
SHOWN. THIS DOES NOT AFFECT THE
REPLACEMENT AND CHARGING PROCEDURES
DESCRIBED.
52 • First unlock and lift the seat.
53 • Disconnect the electrical system plug (A) from
the battery plug (B) by pressing on the sides of
the plugs and pulling apart.
54 • Remove the battery retainer by squeezing in on
the sides and sliding it free of the slot in the body.
55 • Remove old battery and replace with new
battery.
56 • Replace the battery retainer.
57 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.

CHARGING THE BATTERY

WARNING: BATTERY CHARGING AND ANY
OTHER WORK ON THE ELECTRICAL SYSTEM
MUST BE CARRIED OUT BY ADULTS.
THE BATTERY CAN ALSO BE CHARGED
WITHOUT REMOVING IT FROM THE TOY.
58 • First unlock and lift the seat.
59 • Disconnect the electrical system plug (A) from
the battery plug (B) by pressing on the sides of
the plugs and pulling apart.
60 • Plug the battery charger into a household
electrical outlet. Connect battery plug (B) to
charger plug C. NOTE: Press firmly until it snaps
into place.
61 • After battery has finished charging (full charge
takes 18-24 hours), disconnect battery charger
from the electrical outlet and then disconnect the
battery plug (B) from the charger plug (C).
62 • Reconnect electrical system plug (A) to battery
plug (B). NOTE: Press firmly until it snaps into
place.
63 • Close the seat. ATTENTION: Always make sure
that the seat is closed and locked after carrying
out any operations inside it.