Battery Warnings; Rules For Safe Driving; Customer Service - Peg-Perego Ducati Desmosedici Evo IGED0924 Use And Care Manual

product must undergo sorted waste collection.
DISPOSAL OF THE BATTERY
• Help protect the environment.
• Used batteries must not be disposed of with
domestic waste.
• They can be left at a used battery or special waste
collection centre. Contact your local authorities for
more information.

BATTERY WARNINGS

Battery charging must be carried out and supervised
by adults only.
Do not allow children to play with the battery.
CHARGING THE BATTERY
• Charge the battery according to the instructions
enclosed with the battery charger and never for
more than 24 hours.
• To avoid damage, the battery should be charged as
soon as the vehicle starts to lose speed.
• If the vehicle is left unused for a long time,
remember to charge the battery and to keep it
disconnected from the electrical system. Repeat the
recharge procedure at least once every three
months.
• The battery must not be charged upside-down.
• Do not forget about the battery which is being
charged! Check it from time to time.
• Only use the battery charger provided and the
original PEG PEREGO battery.
• The battery is sealed and does not require
maintenance.
• Do not remove the battery charger from the socket
by pulling the cable.
• Do not move the toy by pulling the battery charger
cable.
• Do not cover the battery charger cable, as this
would cause it to overheat.
• Do not place the cable and/or battery on hot
surfaces.
• Take care on how and where you wrap the cable to
so as not to damage it or compromise its operation.
WARNING
• THE BATTERY CONTAINS CORROSIVE TOXIC
SUBSTANCES.
DO NOT TAMPER WITH IT.
• The battery contains acid-based electrolytes.
• Do not create direct contact between the battery
terminals, avoid strong impacts: risk of explosion
and/or fire.
• While charging, the battery produces gas. Charge
the battery in a well-ventilated environment, away
from sources of heat and flammable materials.
• The flat battery must be removed from the vehicle.
• It is not advisable to bring the battery into contact
with clothes, as it could damage them.
• Only use batteries or accumulators of the
recommended kind.
IF THERE IS A BATTERY LEAK
Protect your eyes. Avoid direct contact with the
electrolyte. Protect your hands.
Put the battery in a plastic bag and follow the
instructions for battery disposal.
IF SKIN OR EYES COME INTO CONTACT WITH
THE ELECTROLYTE
Thoroughly rinse the area concerned with running
water.
Consult a doctor immediately.
IF THE ELECTROLYTE IS SWALLOWED
Rinse the mouth and spit out the water.
Consult a doctor immediately.
MAINTENANCE AND VEHICLE
CARE
• Do not disassemble or try to repair the vehicle on
your own. Contact an authorised Peg Perego
customer support centre.
• The toy should not be left anywhere with a
temperature below 0°C. If it were to be used
without being warmed up to a temperature above
0°C, irreversible damage could be caused to the
motors and batteries.
• Check the condition of the vehicle regularly, paying
particular attention to the electrical system, the plug
connections, the terminal protectors and the
battery charger. If defects are identified, the
electrical vehicle and the battery charger must not
be used.
• Always disconnect the battery charger from the toy
before carrying out cleaning, maintenance, or any
type of intervention.
• For repairs use only original PEG PEREGO spare
parts.
• PEG PEREGO do not accept any responsibility for
cases of tampering with the electrical system.
• Do not leave the batteries or the vehicle close to
sources of heat like radiators, fireplaces, etc.
• Protect the vehicle from water, rain, snow, etc. Using
the vehicle on sand or mud may damage the
buttons, motors and gears.
• Lubricate moving parts like bearings, steering, etc.
periodically with light oil.
• The vehicle surfaces can be cleaned with a damp
cloth and, if necessary, with non-abrasive domestic
cleaning products.
• Cleaning must only be carried out by adults.
• Never dismantle the vehicle mechanisms or motors,
unless authorized by PEG PEREGO.

RULES FOR SAFE DRIVING

For the safety of the child, before starting up the
vehicle read and carefully follow the following
instructions.
• Teach the child how to use the vehicle properly for
safe and enjoyable driving.
• The toy must be used with caution, as it requires
substantial dexterity in order to avoid falls or
collisions which could cause injuries to the user or
third parties.
• Before starting, check that there are no people or
objects obstructing the vehicle's path.
• Drive with hands on the handlebars/steering wheel
and always watch the road ahead.
• Brake in good time to avoid collisions.
ATTENTION! The item is equipped with a brake
system which needs to be appropriately illustrated to
the child by an adult.
WARNING!
• Check that all the wheel fixing studs/nuts are
fastened properly.
• If the vehicle is overloaded, as can happen on soft
sand, mud, or very uneven ground, the overload
switch will immediately disconnect the power. The
power supply will be restored after a few seconds.
UNINTERRUPTED FUN: Keep a spare set of charged
batteries ready for use.
PROBLEMS?
THE VEHICLE DOES NOT WORK?
• Check that there are no disconnected cables under
the accelerator plate.
• Check the operation of the accelerator button and
replace it if necessary.
• Check that the battery is connected to the
electrical system.
THE VEHICLE LACKS POWER?
• Charge the batteries. If after charging the problem
persists, have the battery and charger checked by an
assistance centre.

CUSTOMER SERVICE

PEG PEREGO offers an after-sales assistance
service, directly or through a network of
authorized assistance centres, for any repairs or
replacements and the sale of original spare parts.
To contact a service center, visit our website:
http://www.pegperego.com
The item's serial number must always be quoted.
Refer to the last illustration in this manual to find
the serial number.
ASSEMBLY INSTRUCTIONS
WARNING
THE VEHICLE MUST BE ASSEMBLED BY ADULTS.
BEWARE WHEN EXTRACTING THE VEHICLE
FROM THE PACKAGING.
ALL THE NECESSARY SCREWS AND SMALL
COMPONENTS ARE STORED IN A BAG INSIDE
THE PACKAGING.
Do not use the toy if you find it damaged after
opening the packaging. Contact the shop where you
bought it or the customer support centre.
Take care in the presence of children while assembling
the toy, given the risks caused by small parts
(ingestion hazard) and the plastic bags that contain
them (choking hazard).
To assemble the toy, you will need a flat-head
screwdriver, a Phillips screwdriver, a hammer, and a
pair of pliers.
ASSEMBLY
1 • Clip the rear mudguard into place by inserting
the 3 tabs in the slots in the bodywork shown by
the arrows.
2 • Turn the body work upside down and attach the
mudguard to it by pressing it, making sure the
centre tab is inserted first (A).
• Repeat steps 1 and 2 on the other side.
3 • Insert the handle in the hole in the bodywork (1)
and turn it downwards (2). PLEASE NOTE: The
two handles are different. Position them with the
flat side facing the saddle.
4 • Turn the bodywork over to access the underside
and attach the handle with the screw provided.
• Repeat steps 3 and 4 with the other handle.
5 • Press the rim (PART A) into the wheel, following
the direction of the tread, and make sure that the
reference pin connects correctly (see figure).
Repeat this operation for another wheel, always
following the direction of the tread.
6 • Insert bushing A into the right-hand wheel (the
right and left wheel refer to the direction of the
tread, according to the travel direction).
7 • Insert the longest axle into the wheel.
8 • Insert an iron washer into the axle.
9 • Insert the axle with the wheel and washer into
the bodywork hole from the right-hand side, as
shown in the figure.
10 • Position bushing B on the other wheel with rim.
11 • Insert the wheel into the axle from the left-hand
side of the bodywork, making sure to insert the
wheel bushing into the motor pentagon.
12 • Position the red press-stud on one of the two
terminal axle parts.
13 • Turn the bodywork upside down, keeping the
press-stud underneath it.
14 • Insert the stud into the black press-stud.
15 • Position it on the other axle terminal, as shown in
the figure, and secure the wheel with stud by
using a hammer.
• Turn the motor to the opposite side and repeat
the operation to secure the other wheel.
16 • Remove the LED system from the handlebar and
insert it into the front plate, as shown in the
figure.
17 • Press the front plate onto the lower part of the
prong, snapping the 3 hooks in place and making
sure that the light connector is inserted in its
housing.
18 • Insert the wiring cable coming out of the body
into its housing on the upper part of the prong,
as shown in the figure.
19 • Insert the front prong into the body until the pin
fits into the bottom part of the front plate, as
shown in the figure. The prong's pin must fit into
the curved part (see detail).
20 • Put the cover on the bodywork and ensure that
the 3 tabs fit into their slots.
21 • Push the threaded steering pin all the way down.
22 • Insert the nut at the lower end of the fork. Hold
it in position and attach it by turning the