Roland VS-2480 Supplementary Manual page 87

Cmp (Compressor):Compresses the entire output signals when the input volume exceeds a specified value.
SW (Switch)
Low Thre (Low Threshold)
Low Ratio (Low Raito)
Low Atck (Low Attack)
Low Rel (Low Release)
Mid Thre (Middle Threshold)
Mid Ratio (Middle Ratio)
Mid Atck (Middle Attack)
Mid Rel (Middle Release)
High Thre (High Threshold)
High Raito (High Ratio)
High Atck (High Attack)
High Rel (High Release)
Mix (Mixer):
Low Level (Low Level)
Mid Level (Middle Level)
High Level (High Level)
Lmt (Limiter):
Sw (Switch)
Thresh (Threshold)
Attack (Attack)
Release (Release)
Out (Output):
SoftClip (Soft Clip)
Level (Level)
*1: If Low Type (Lo Type) or High Type (Hi Type) is set to "Shlv (Shlving Type)," the setting for Lo Q or High Q is
invalid.
• With Compressor, the level is automatically adjusted to the optimal with the settings for Threshold (Thres) and Raito
(Ratio). Setting Attack (Atck) to a relatively long time may cause distortion. For this reason, a margin of -6 dB is
provided. Adjust the Mixer (Mix) level as required.
• "Mastering Tool Kit" cannot be used on EFFECT2, 4, 6, and 8 (even-numbered effects).
• When "Mastering Tool Kit" is used on EFFECT1, 3, 5, and 7 (odd-numbered effects), EFFECT2, 4, 6, and 8 (even-
numbered effects) cannot be used.
• "Mastering Tool Kit" cannot be used on the projects with 64kHz or higher sampling rate.
On, Off Turns the compressor on or off.
-24–0 dB Sets the volume at which the compressor for the low frequency band starts working.
1:1.0–1:16, 1:INF Sets the ratio at which the output in the low frequency band is suppressed
when the input level has exceeded the low threshold level.
0–100 ms Sets the time until when the low frequency band compressor starts working
after the input level has exceeded the low threshold level.
50 ms–5.000 s Sets the time until when the low frequency band compressor stops working
after the input level has dropped below the low threshold level.
-24–0 dB Sets the volume at which the compressor in the middle frequency band
starts working.
1:1.0–1:16, 1:INF Sets the ratio at which the output in the middle frequency band is
suppressed when the input level has exceeded the middle threshold level.
0–100 ms Sets the time until when the middle frequency band compressor starts
working after the input level has exceeded the middle threshold level.
50 ms–5.000 s Sets the time until when the middle frequency band compressor stops
working after the input level has dropped below the middle threshold level.
-24–0 dB Sets the volume at which the compressor for the High frequency band starts
working.
1:1.0–1:16, 1:INF Sets the ratio at which the output in the High frequency band is suppressed
when the input level has exceeded the High threshold level.
0–100 ms Sets the time until when the High frequency band compressor starts
working after the input level has exceeded the High threshold level.
50 ms–5.000 s Sets the time until when the High frequency band compressor stops working
after the input level has dropped below the High threshold level.
Adjusts the volume by frequency band.
-80– +6 dB Sets the volume in the low frequency band after passing through the
expander and compressor.
-80– +6 dB Sets the middle frequency band volume after passing through the expander
and compressor.
-80– +6 dB Sets the volume in the High frequency band after passing through the
expander and compressor.
Prevents distortion by suppressing signals at High levels.
On, Off Turns the limiter on or off.
-24–0 dB Sets the volume at which the limiter starts working.
0–100 ms Sets the time until when the limiter starts working after the input level has
exceeded threshold level.
50 ms–5.000 s Sets the time until when the limiter stops working after the input level drops
below the threshold level.
Provides settings concerning overall output.
On, Off Suppresses conspicuous distortion that may occur when the effect of
compressor/limiter has been applied excessively.
-80– +6 dB Sets the overall volume after passing through the limiter.
Algorithm List
87