Roland VC-200HD Owner's Manual page 38

Menus and settings
200–275 Processing Parameter (continued)
Item Item Name
Number
210 Out Zoom
211 Out H Position
212 Out V Position
220 Noise Reduction
221 Enhancement
222 Video Red Gain
223 Video Green Gain
224 Video Blue Gain
240 AudioDelay Time
250 Audio Low Gain
251 Audio Mid Gain
252 Audio High Gain
260 Sync Source
261 Sync Adjust
270 TC Generate
271 TC Offset
* The values enclosed in a [box] are the factory defaults.
* For items 201-212 and 220-224, please adjust while confirming on a video monitor.
38
Description and Available Settings
Adjusts the magnification of the output video.
50–[100]–200%: Larger numerical values make the image larger.
* The maximum value that can be selected changes according to the combination of the input video format (p. 28)
and the output format (p. 29).
Adjusts the horizontal position of the output video when the aspect ratios of the input video (p. 28) and
the output format (p. 29) are different and "Side Panel/Let" or "Crop" is selected with "200: Scaling Type."
-100–[0]– +100 %: Larger values move the image right.
Adjusts the vertical position of the output video when the aspect ratios of the input video (p. 28) and the
output format (p. 29) are different and "Side Panel/Let" or "Crop" is selected with "200: Scaling Type."
-100–[0]– +100 lines: Larger values move the image up.
Obscures noise in the input video so it is unnoticeable. If it is set too strong, the video resolution may be
reduced.
[Off]: Do not use 1–63:
The strength of the Noise Reduction
Emphasizes the edges of the input video. If set too strong, the edges may look jagged.
[Off]: Do not use
1–63: Strength of Enhancement
Sets the gain value for red in the video being output.
[0]–100%: Larger numerical values indicate a stronger red color.
Sets the gain value for green in the video being output.
[0]–100%: Larger numerical values indicate a stronger green color.
Sets the gain value for blue in the video being output.
[0]–100%: Larger numerical values indicate a stronger blue color.
Sets the delay applied to the output audio.
0.00–[1.00]–15.00f
* The time per frame changes according to the frame rate in the value set in "300:Video Out Format."
Therefore, the range of values displayed on the screen (???.? ms) is as follows.
0.00 – 500.5 -When the frame rate is 59.94i/59.94p
0.00 – 600.0 -When the frame rate is 50i/50p
Sets the low-range gain value for the sound being output.
-12dB–[0]– +12dB:
Increasing the numerical value increases the low-range gain value.
Sets the mid-range gain value for the sound being output.
-12dB–[0]– +12dB: Increasing the numerical value increases the mid-range gain value.
Sets the high-range gain value for the sound being output.
-12dB–[0]– +12dB: Increasing the numerical value increases the high-range gain value.
Sets the synchronizing signal input source.
[Auto]: Selected automatically.
REF Input: Selects the REF INPUT connector.
Video Input: Selects the video being used.
Internal: Uses the synchronizing signal generated internally.
Fine tunes the synchronizing signal.
-1000–[0]– +1000 clock: May be adjusted in this range.
Selects the timecode to embed in the HDV, DV, or HD-SDI output.
* On the VC-200HD, this is set to "Off" at the factory.
[Off]: Time code is not embedded. Free Run: Timecode is generated internally. The timecode is generated
from when the power is turned on or when "271: TC Offset" is set.
Free Run: The time code starts (preset) from the moment settings are made with "271: TC Offset."
[Thru]: Use the timecode input from an external source. The timecode that is used will be that which is
embedded in the signal of the video connector being used.
* This setting is ignored when the frame rates of the input video (p. 28) and the output format (p. 29) are different.
The time code output here is the same as when "Free Run" is set.
Offset: Output the timecode input from an external source with the offset set with "271: TC Offset" ap-
pended to it. The TC that is used will be that which is embedded in the signal of the video connector being
used.
Sets the offset to apply when "Offset" is selected with "270: TC Generate." This value will be the time
code's preset value when "Free Run" is set for "270: TC Generate."
The hour (h), minute (m), second (s), and frame (f) values can be set independently for this item.
[00h00m00s00f]–23h59m59s24f (When the frame rate value set for "300:Video Out Format" is 50i or 50p)
[00h00m00s00f]–23h59m59s29f (When the frame rate value set for "300:Video Out Format" is 59.94i or 59.94p)
* The available range for this parameter changes when the "300: Video Out Format" parameter is changed.
* When "Free Run" is set for "270: TC Generate," the time code count is reset when this item setting is changed.