Roland RG-7 Midi Implementation Manual page 21

■EFX Type Table
MSB LSB
01H 00H
01H 01H
01H 02H
01H 04H
01H 05H
01H 06H
01H 10H
01H 11H
01H 12H
01H 13H
01H 07H
01H 14H
01H 20H
01H 29H
01H 2aH
01H 23H
01H 27H
01H 28H
01H 21H
01H 03H
01H 2bH
01H 25H
01H 26H
01H 2cH
01H 30H
01H 31H
01H 42H
01H 40H
01H 41H
01H 43H
01H 44H
01H 45H
01H 22H
01H 2dH
03H 00H
01H 5bH
01H 5cH
01H 5dH
01H 5eH
01H 5fH
01H 50H
01H 51H
01H 52H
01H 57H
01H 59H
01H 5aH
01H 72H
01H 75H
01H 56H
02H 00H
02H 01H
02H 02H
02H 03H
02H 04H
02H 05H
02H 06H
02H 07H
02H 08H
02H 09H
02H 0aH
02H 0bH
00H 40H
Type
Equalizer
Spectrum
Enhancer
Isolator
Low Boost
High Pass Filter
Overdrive
Distortion
Overdrive2
Distortion2
Speaker Simulator
Guitar Amp Simulator
Phaser
Multi Stage Phaser
Infinite Phaser
Stereo Flanger
3D Flanger
2Band Flanger
Auto Wah
Humanizer
Ring Modulator
Tremolo
Auto Pan
Slicer
Compressor
Limiter
Stereo Chorus
Hexa Chorus
Tremolo Chorus
Space D
3D Chorus
2 Band Chorus
Rotary
Rotary2
Rotary Multi
Stereo Delay1
Stereo Delay2
Stereo Delay3
Stereo Delay4
Stereo Delay5
Monaural Delay
Modulation Delay
Triple Tap Delay
3D Delay
Tape Echo
Reverse Delay
Lo-Fi
Telephone
Gate Reverb
Overdrive -> Chorus
Overdrive -> Flanger
Overdrive -> Delay
Distortion -> Chorus
Distortion -> Flanger
Distortion -> Delay
Enhancer -> Chorus
Enhancer -> Flanger
Enhancer -> Delay
Chorus -> Delay
Flanger -> Delay
Chorus -> Flanger
Damper Resonance
■EFX Parameter Map
● 0100: EQUALIZER
This is a four-band stereo equalizer (low, mid x 2, high).
No Parameter Value Default
1 Low Freq 0 - 1 200, 400 Hz
2 Low Gain # 0 - 30 -15- +15 dB
3 Mid1 Freq 0 - 16 200-8000 Hz
4 Mid1 Gain 0 - 30 -15- +15 dB
0.5, 1.0, 2.0,
5 Mid1 Q 0 - 4
4.0, 8.0
6 Mid2 Freq 0 - 16 200-8000 Hz
7 Mid2 Gain 0 - 30 -15- +15 dB
0.5, 1.0, 2.0,
8 Mid2 Q 0 - 4
4.0, 8.0
2000, 4000,
9 High Freq 0 - 2
8000 Hz
10 High Gain # 0 - 30 -15- +15 dB
11 Level 0 - 127 0-127
● 0101: SPECTRUM
This is a stereo spectrum. Spectrum is a type of filter which modifies the timbre by boosting
or cutting the level at specific frequencies.
No Parameter Value Default
1 Band1 (250Hz) 0 - 30
Band2 (500Hz)
2 0 - 30
#
Band3
3 0 - 30
(1000Hz)
Band4
4 0 - 30
(1250Hz) #
-15- +15 dB
Band5
5 0 - 30
(2000Hz)
Band6
6 0 - 30
(3150Hz)
Band7
7 0 - 30
(4000Hz)
Band8
8 0 - 30
(8000Hz)
0.5, 1.0, 2.0,
9 Q 0 - 4
4.0, 8.0
10 Level 0 - 127 0-127
● 0102: ENHANCER
Controls the overtone structure of the high frequencies, adding sparkle and tightness to the
sound.
No Parameter Value Default
1 Sens # 0 - 127 0-127
2 Mix # 0 - 127 0-127
3 Low Gain 0 - 30 -15- +15 dB
4 High Gain 0 - 30 -15- +15 dB
5 Level 0 - 127 0-127
● 0104: ISOLATOR
This is an equalizer which cuts the volume greatly, allowing you to add a special effect to
the sound by cutting the volume in varying ranges.
No Parameter Value Default
Boost/Cut
1 0 - 64
Low
Boost/Cut Mid
2 0 - 64 -60- +4 dB
#
Boost/Cut
3 0 - 64
High #
Anti Phase
4 0 - 1 OFF, ON
Low Sw
Anti Phase
5 0 - 127 0-127
Low Level
Anti Phase Mid
6 0 - 1 OFF, ON
Sw
Anti Phase Mid
7 0 - 127 0-127
Level
MIDI Implementation
Description
Frequency of the low range
Gain of the low range
Frequency of the middle range 1
Gain of the middle range 1
Width of the middle range 1
Set a higher value for Q to narrow the
range to be affected.
Frequency of the middle range 2
Gain of the middle range 2
Width of the middle range 2
Set a higher value for Q to narrow the
range to be affected.
Frequency of the high range
Gain of the high range
Output Level
Description
Gain of each frequency band
Simultaneously adjusts the width of
the adjusted ranges for all the fre-
quency bands.
Output Level
Description
Sensitivity of the enhancer
Level of the overtones generated by
the enhancer
Gain of the low range
Gain of the high range
Output Level
Description
These boost and cut each of the High,
Middle, and Low frequency ranges.
At -60 dB, the sound becomes inaudi-
ble. 0 dB is equivalent to the input
level of the sound.
Turns the Anti-Phase function on
and off for the Low frequency ranges.
When turned on, the counter-chan-
nel of stereo sound is inverted and
added to the signal.
Adjusts the level settings for the Low
frequency ranges.
Adjusting this level for certain fre-
quencies allows you to lend empha-
sis to specific parts. (This is effective
only for stereo source.)
Settings of the Anti-Phase function
for the Middle frequency ranges
The parameters are the same as for
the Low frequency ranges.
21