Table of Contents
Advertisement
Precautions for installation
Panasonic assumes no responsibility for injuries or property damage resulting from failures arising out of
improper installation or operation inconsistent with this documentation.
This camera is designed to be used indoors.
This product is not operable outdoors.
Do not expose this camera to direct sunlight for hours and
do not install the product near a heater or an air condi-
tioner. Otherwise, it may cause deformation, discoloration
and malfunction. Keep this camera away from water and
moisture.
Power supply
This product has no power switch.
When turning off the power, turn off a power supply or
remove a power cable. When the power cable of the
product is connected to the power supply device, the
power will be supplied to the product. When the product
is supplied, the product will perform panning, tilting,
zooming and focusing.
Before cleaning the product, make sure that the power
cable is not connected to the main power supply.
Installation area for this product
Select an appropriate place for the installation area (such
as a strong wall or ceiling) in your particular environment.
• When the installation area is not strong enough, rein-
force and strengthen it or use an optional mount
bracket (WV-Q105 or WV-Q126A).
• When the product is installed on a wall, use the wall
mount bracket (WV-Q119).
• Do not mount the product on a plaster board or a
wooden section because they are too weak. If the
product is unavoidably mounted on such a section,
the section shall be sufficiently reinforced.
Do not place this product in the following places:
• Locations where it may get wet from rain or water
splash (including under the eaves, etc.)
• Locations where a chemical agent is used such as a
swimming pool
• Locations subject to moisture or oil smoke such as a
kitchen
• Locations that have a specific environment that is
subject to an inflammable atmosphere or solvents
• Locations where a radiation, an X-ray, a strong radio
wave or a strong magnetic field is generated
• Locations where corrosive gas is produced, locations
where it may be damaged by briny air such as sea-
shores
• Locations where the temperature is not within the
specified range (☞ page 31)
• Locations subject to vibrations, such as on vehicles,
marine vessels, or above product lines (This product
is not designed for on-vehicle use.)
• Locations subject to condensation as the result of
severe changes in temperature
12
Mounting method for this product
This product is designed to be used as a pendant mount
camera. If the product is mounted on a desktop or at a
slant, it may not work correctly and its lifetime may be
shortened.
Protection from lightning
When connecting to a network using the network cable of
this product, observe the following.
• Do the wiring so that the network is not affected by
lightning.
Procure fixing screws separately.
The screws that mount the camera mount bracket (acces-
sory) and other brackets on a ceiling or a wall are not sup-
plied. Prepare them according to the material and strength
of the area where the product is to be installed.
<Installing the unit directly on a ceiling using the camera
mount bracket (accessory)>
• Required screws: M4 (4 pcs.)
• Minimum pull-out strength: 196 N {44 lbf} (per 1 pc.)
Screw tightening
• The screws and bolts must be tightened with an
appropriate tightening torque according to the materi-
al and strength of the installation area.
• Do not use an impact driver. Use of an impact driver
may damage the screws or cause tightening exces-
sively.
• When a screw is tightened, make the screw at a right
angle to the surface. After tightening the screws or
bolts, perform checks to ensure that the tightening is
sufficient enough so that there is no movement or
looseness.
Make sure to remove this product if it will no longer
be used.
Radio disturbance
When this product is used near TV/radio antenna, strong
electric field or magnetic field (near a motor, a transformer
or a power line), images may be distorted and noise may
be produced.
PoE (Power over Ethernet)
Use a PoE hub/device that is compliant with IEEE802.3af
standard.
Advertisement
Table of Contents
