Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CDA HG3601FR
Summary of Contents for CDA HG3601FR
- Page 1 Domino Cooking Hobs Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...
-
Page 2: Appliance Information
The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. -
Page 3: Before Using For The First Time
Important Safeguards and Recommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will become very hot. Do not touch hot parts. –... -
Page 4: Features And Technical Data
Features and Technical Data HG3601FR HG3602FR This appliance is class 3 Fig. 1a Fig. 1b Cooking Points 1. Triple ring burner (TR) - 3,50 kW 2. Rapid burner (R) - 3,00 kW 3. Semi-rapid burner (SR) - 1,75 kW Control Panel 4. -
Page 5: Gas Burners
How to Use the Hob Gas Burners Gas flow to the burners is adjusted by turning the knobs (illustrated in fig.2) which control the valves. Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: –... - Page 6 Lighting Gas Burners In order to light the burner, you must: 1 – Press in the corresponding knob and turn counter-clockwise (fig. 3) to the full flame position marked by the symbol and hold the knob in until the flame has been lit. In the case of a mains failure light the burner with a match or lighted taper.
- Page 7 Choice of Burner The symbols printed on the panel by the side of the knob indicate which burner you are controlling. Choose a suitable burner depending on the cookware diameter and capacity. The pan diameter should be suitable for the burner power to make the most of the burner's high efficiency and not waste fuel.
-
Page 8: Correct Use Of Triple-Ring Burner
Correct use of Triple-Ring Burner Model: The flat-bottomed pans are to be placed directly onto the pan-support. HG3601FR To use the WOK you need to place the proper stand in order to avoid any faulty operation of the triple-ring burner (Figs. 5a - 5b). - Page 9 Fig. 6 Fig. 7...
-
Page 10: Cleaning And Maintenance
Cleaning and Maintenance General Tips – Before cleaning the hob switch it off and wait for it to cool down. CAUTION: – Clean with a cloth, hot water and soap or liquid detergent. Do not use harsh – Do not use products which are abrasive, corrosive or chlorine based. abrasive cleaners –... -
Page 11: Burners And Grids
Damage to the appliance will occur if not observing this condition and this may result in serious injury to the user. The manufacturer declines every responsibility for any inconvenience resulting from the inobservance of this condition. HG3602FR HG3601FR Fig. 8... - Page 12 Correct Position of Triple Ring Burner Model: The triple ring burner must be correctly positioned (see fig. 9); the burner HG3601FR ribs must be fitted in their housing as shown by the arrow. The burner correctly positioned must not rotate (fig. 10).
- Page 13 Correct Positioning of the Semi-rapid and Rapid Burners Model: – It is very important to check that the burner flame spreader F and the cap HG3602FR C have been correctly positioned (see figs. 13 and 14). They shall be level and must not rotate.
-
Page 14: Tips For Installation
TIPS FOR INSTALLATION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a room or space containing a bath or a shower. – The appliance must not be installed in a bed-sit room of less than 20m –... -
Page 15: Installation
Installation Technical Information for the Installer HG3601FR In order to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 16 has to be made, bearing in mind the following: – Within the unit, between the bottom of the hob and the upper surface of a shelf there must be a clearance of at least 30mm. -
Page 16: Fastening The Cooktop
Fastening the Cooktop Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to benches from 30 to 40 mm thick.The kit includes four R brackets and four self-threading screws S (figs. 19, 20). –... -
Page 17: Gas Supply Requirements
Gas Supply Requirements Important Note This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance). – Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. -
Page 18: Gas Connection
The installation must conform to the relevant British Standards. CDA are not legally able to provide any assistance in the installation of gas appliances except to suitably qualified and registered installers. Any suitably qualified and registered fitter requiring help must provide name, address and registration number. -
Page 19: Connection To The Gas Supply
Gas connection Cat: II 2H3+ The fitting (fig. 21) is made up of: – 1 nut A – 1 elbow fitting C – gasket F Connection to the Gas Supply – Be careful when flexible pipes are used that they do not come into contact with moving parts. –... -
Page 20: Conversion To Natural Gas Or Lpg
– Using a wrench, substitute the nozzle injectors J (Figs. 23 - 24) with those most suitable for the kind of gas for which it is to be used. The burners are made in such a way so as not to require regulation of the primary air. Semi-Rapid HG3602FR HG3601FR Triple Ring and Rapid burner burners Fig. -
Page 21: Lubrication Of The Gas Taps
Regulating the Burner Minimum Setting When changing from one type of gas to another, the minimum tap output must also be correct, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum to the minimum position. -
Page 22: Mains Electricity Connection
Mains Electricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible. Warning! This appliance must be earthed The manufacturer declines all responsibility for any problem caused by failure to observe this rule. THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. -
Page 23: Appliance Servicing
Appliance Servicing CDA provide a quality and effective after-sales service to cover all your servicing needs. Please attach your receipt to this page for safekeeping. Please help us to help you by having the following information available when booking a service-call: 1. - Page 24 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...