Advertisement
Operating The Product
Controls: See Fig. 3
Icon
Display
Function
Power /
A
-
Standby
Sleep
B
Timer
Flame Effect
Low
f1
Flame
High
f2
C
Flame
Demo
fp
Mode
Off
-
Colour Theme
1
Theme 1
D
Theme
2-8
2-8
Bright-
E
-
ness
Heat
Low Heat
F
High Heat
Cool Blow
-
Off
Temp
G
-
Down
H
-
Temp Up
User Modes:
Mode Name /Discription
Change Celsius (
C) to Fahrenheit (
0
Disable/Enable Heat Options
Description
Press once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless the product has
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5 hr to 8.0 hr before turning off.
The remaining time on the 'SLEEP TIMER' displays.
'FLAME EFFECT' button cycles the unit
DEMO MODE and OFF.
This setting will run the flame effect at a low brighness level. (The display will show F1)
This setting will run the flame effect at a high brighness level. (The display will show F2)
This setting will slowly pulse the flame effect between low and high brightness. (The display will show FP)
This will turn the flame effect off. If the heater is running, the display will activate and remain active to read the
set temperature and show if the product is on LOW HEAT/ HIGH HEAT/COOL BLOW.
'Colour Themes' are setting which change the colour of the fuel bed there are eight different themes
Theme 1 is a 'Demo Mode' this setting will scroll throught all of the colour settings you can 'Pause' this demo
mode by pressing the 'Brightness Button' /
'Brightness Button' /
in which case display will read
Themes 2-8 are preset colours that remain static.
This button switches themes 2-8 between full brightness and half brightness. This button also interacts with
the product when set on theme as perviously described above
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT, COOL BLOW and
OFF. The heat setting will be indicated by an icon in the floating display see Fig.1.
When the flame effect is 'ON' the floating display will turn off after 5 seconds, however if the heater is be-
ing used independantly of the flame effect. The low heat or high heat icon will appear continuously in the
floating display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW HEAT' icon and the
letters 'LO' appearing in the display.
(This icon is Orange in Colour)
This icon in the floating display indicates 'HIGH HEAT' this setting will be indicated by the 'HIGH HEAT' icon
and the letters 'HI' appearing in the display.
(This icon is Red in Colour)
This icon in the floating display indicates 'COOL BLOW' this setting will be indicated by the 'COOL BLOW'
icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the floating display. Note the blower
will run for 10-20 seconds after being turned off this is to ensure the product cools down safely.
Press multiple times to lower the heater temperature in 1
set 5
C.
0
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the room
temperature as detected by the product. If the set temperature is lower than the detected room temperature
the heater will not activate.
Press multiple times to increase the heater temperature in 1
be set 37
C.
0
Note: Once you stop at your desired temperature this will flash 3 times, then the display will show the room
temperature as detected by the product. If the set temperature is lower than the detected room temperature
the heater will not activate.
Action (Actions cannot be input by remote control)
F) Press both 3 Dot Button (
0
beep is heard and display flashes. (To revert back to Celsius repeat this action)
Hold both 1 Dot Button (
heater has been disabled the display will read "--" and beep. To enble heat repeat this action.
(This icon is Green in Colour)
sequentially through the 4 setting, LOW FLAME, HIGH FLAME,
in which case the display will read
1.U
C increments. The lowest temperature that can be
0
C increments. The highest temperature that can
0
)
and 2 Dot (
)
(
)
) and Flame Button
, on the unit, for 2 seconds, when the
1.p
to 'Unpause' press the
on the unit and hold until
Advertisement
