Operating The Product - Dimplex Optimyst CAS500P-RGB-EU Operating Instructions Manual

OPERATING THE PRODUCT

This section describes how to activate your fire using either the manual controls or remote control.
MAINS SWITCH
The mains switch is located under the fuel bed on the module and controls the electricity to the appliance (Fig 23A).
Note: This switch must be in the 'ON' ( I ) position for each appliance to operate.
MANUAL CONTROLS
Manual controls are located on the cassette module under the fuel bed. There are also manual controls on the tethered
receiver unit which is fitted loose.
REMOTE CONTROL
The remote control is supplied with 2x CR2032 batteries already fitted. Pull both tabs from the rear cover to engage the
batteries (Fig 24) and allow remote operation.
Note: The tethered receiver must be fitted to the product for remote control operation.
PAIRING THE REMOTE CONTROL
The remote control has wireless Bluetooth technology and needs to be paired to the receiver. This can be done by
following the steps below.
1.
Press the rocker switch to the on (I) position.
2.
Press the button on the Button Panel; the product will turn on.
3.
Press the button on the Button Panel, the LED's will start to slowly blink on and off.
4.
Press the button on the remote control; the product LEDs will flash quickly five times and the product will then
automatically switch off. The remote control is now paired to the product and can be used to switch it back on.
TO REPLACE THE BATTERIES
1.
Remove battery cover of the remote control using a Philips screwdriver (Fig 25).
2.
Correctly install two 3 Volt (CR2032 or similar) battery in the battery holder with the + side facing up .
3.
Secure the battery cover using the previously removed screw.
Batteries must be recycled or disposed of properly.
Check with your Local Authority or Retailer for recycling advice in your area.
Frequency band(s) this product operates in: 2.4GHz
Maximum radio-frequency power transmitter in the frequency band(s) this product operates in: 8.23dBm
CREATING YOUR PERFECT OPTIMYST EFFECT
With Optimyst technology you can create a flame effect that is unique to you. First ensure the appliance is on by pressing
the main switch to I (Fig 10). To turn on the flames press the
the ENTER button to activate and use the
FLAME COLOUR: There are 6 colour themes to chose from. To adjust the flame colour, navigate to colour icon
the remote and press enter. Use
manual controls press the
TIP: Orange is the go to colour for a traditional authentic look, but when it is time for a celebration switch to the Prism
theme that cycles through a rainbow of colours. In summer time blue is both cooling and calm, whilst green always
draws attention at Holloween.
FLAME INTENSITY: You can adjust the flame intensity by selecting
to choose from, press
manual controls press the
time to react to the changes you make.
TIP: Lower levels give a gentle slow flame, higher levels a faster fuller flame.
FLAME BRIGHTNESS: During spring and summer when the days or longer you may need to increase the brightness
of the flame to make it more vivid. Select the brightness icon
brightness options 1 to 6 and ENTER to select.
TIP: depending on the lighting, surrounding décor colours and airflow in the room, making adjustments the flame
intensity, colour and brightness can make a real difference to you look and feel of this fireplace.
SOUND: For authenticity you can add the sound of crackling logs to the flame effect. Select the
to adjust the sound level by pressing
the sound on/off.
or
or to toggle between options 1 to 6 flame themes and ENTER to select. On the
repeatedly to cycle through the colours.
or to adjust intensity, F1 being the lowest setting and F6 being the highest setting. On the
and buttons to adjust the flame to your desired level. Please give the flame generator
or followed by ENTER to select. On the manual controls the
button on the manual controls. If using the remote, press
buttons to navigate to the
and press ENTER to adjust. There are 6 levels
on the romote and press enter. Use
8
icon and press ENTER to select.
icon on the remote
on
or to adjust
button turns