Advertisement
Operating The Product
Operating Instructions - See Fig. 3
Icon Display
Funtion
Power /
A
-
Standby
Flame
+
Up
Flame
-
B
Down
Flame
fc
Cycling
-
Off
Sleep
C
Timer
Low
Heat
D
High
Heat
Cool
Blow
-
Off
Temp
E
-
Up
Temp
F
-
Down
LED
G
-
COLOUR
User Modes:
Mode Name /Discription
Change Celsius (
C) to Fahrenheit (
0
Description
Press Once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
'FLAME EFFECT' button this turns the flame effect ON or OFF independently of the
products other features.
This Button will increase the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY increase the brightness level.
This Button will decrease the brightness of the flame effect. There are 5 brightness settings
shown as F1, F2, F3, F4, F5. This button will ONLY decrease the brightness level.
This setting is set by pressing the Flame Up button once more after F5. this will cause the
brightness of the flame effect to cycle from F2 to F5 in a continuous Loop.
This will turn the flame effect off. If the heater is ON, the display will activate and remain
active to read the set temperature and show if the product is on LOW HEAT/ HIGH HEAT/
COOL BLOW.
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the 'SLEEP TIMER' displa
ys.
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display see Fig.1.
When the flame effect is 'ON' the display will turn off after 5 seconds, however if the
heater is being used independently of the flame effect. The low heat or high heat icon
will appear continuously in the display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW
HEAT' icon. To Adjust the temperature setting the Temp Down or Temp Up buttons de-
scribed below must be used.
(This icon is Orange in Colour)
This icon in the display indicates 'HIGH HEAT' this setting will be indicated by the 'HIGH
HEAT' icon. To Adjust the temperature setting the Temp Down or Temp Up buttons de-
scribed below must be used.
(This icon is Red in Colour)
This icon in the floating display indicates 'COOL BLOW' this setting will be indicated by
the 'COOL BLOW' icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
P r e s s m u l t i p l e t i m e s t o i n c r e a s e t h e h e a t e r t e m p e r a t u r e i n 1
c r e m e n t s .
T h e
h i g h e s t
When High Heat is selected, the letters 'HH' appear in the display, this means
the heat will remain ON continusously and is not controlled by the thermostat.
P r e s s m u l t i p l e t i m e s t o l o w e r t h e h e a t e r t e m p e r a t u r e i n 1
c r e m e n t s .
T h e
l o w e s t
Press multiple times to change the colour of the coloured fuel bed. The colour can
be set as Orange, Red, Green, Blue, or cycling through all four colours continuously.
Action (Actions cannot be input by remote control)
F) Press both 3 Dot Button (
0
beep is heard and display flashes. (To revert back to Celsius repeat this action)
t e m p e r a t u r e
t h a t
t e m p e r a t u r e
t h a t
)
and 2 Dot (
(This icon is Green in Colour)
0
C i n -
0
c a n
b e
s e t
3 0
0
C i n -
0
c a n
b e
s e t
i s 1 8
)
on the unit and hold until
C .
C .
Advertisement
