Operating The Product - Dimplex Optiflame Gorstan GST20 Operating Instructions Manual

Operating The Product

WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY
AND/OR DAMAGE.
Activating the remote control:
To activate the remote control remove the clear battery isolation strip at the base of the remote control, which is used to
ensure your remote control reaches you fully charged.
To replace the battery:
Remove the screw, follow the instruction on the back of the remote to release the battery housing. Slide the battery cover
open. Install 1 x 3V CR2025 Lithium battery in the battery holder. The positive (+) side of the battery faces up.
Close the battery cover and replace the screw
Operating Instructions - See Figure 8
Icon Display Funtion
Power /
A -
Standby
F1 / F2 /
F3
B
Flame
P
Pulsing
-
Off
Sleep
C
Timer
Low
Heat
D
High
Heat
Cool
Blow
- Off
E 30 Temp Up
Temp
F
18 Down
Flame
G -
Colour
Top-light
H
-
Fuel Bed
Description
Press Once to turn the product 'ON'.
Press a second time to put the product into 'STANDBY'
(When returning from 'STANDBY' mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
'FLAME EFFECT' button, this turns the flame effect ON independently of the products
other features.
This Button will change the brightness of the flame effect.
There are 3 brightness settings shown as F1, F2, F3.
This setting is set by pressing the Flame Up button once more after F3. This will cause the
brightness of the flame effect to cycle randomly, creating a flickering effect.
If the flame effect is turned off, but the heater is ON, the display will remain
low heat/high heat/cold blow icon will appear continuously in the display indicating
the heater setting.
Press multiple times to change the 'SLEEP TIMER' in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the 'SLEEP TIMER' displays.
(This icon is Green in colour)
'HEAT' button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display.
When the flame effect is 'ON' the display will turn off after 5 seconds, however if the
heater is being used independently of the flame effect. The low heat/high heat/cold
blow icon will appear continuously in the display.
This setting will run the heater at 'LOW HEAT' this setting will be indicated by the 'LOW
HEAT' icon and the letters 'LO' appearing in the display. To adjust the temperature
setting the Temp Down or Temp Up buttons described below must be used.
(This icon is Orange in Colour)
This icon in the display indicates 'HIGH HEAT' this setting will be indicated by the 'HIGH
HEAT' icon and the letters 'HI' appearing in the display. To Adjust the temperature setting
the Temp Down or Temp Up buttons described below must be used.
(This icon is Red in Colour)
This icon in the floating display indicates 'COOL BLOW' this setting will be indicated by
the 'COOL BLOW' icon and the letters 'CB' appearing in the display.
(This icon is Blue in Colour)
This switches the heater and blower 'OFF', no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
Press multiple times to increase the heater temperature in 2
temperature that can be set 30
When High Heat is selected, the letters 'HH' appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
Press multiple times to lower the heater temperature in 2
temperature that can be set is18
Press to turn ON/OFF the coloured accent within the flame effect.
Press to turn ON/OFF the Top light illuminating the fuel bed.
0 C.
0 C increments. The lowest
0 C.
active. The
0 C increments. The highest
7