Kodak EasyShare 5300 Start Here

Start here
EasyShare 5300
All-in-One Printer
Print
Copy
Scan
Box contents
Rotate Zoom Proofsheet Transfer
Photo
Scan Copy
Menu Help
Cancel Start On/Off
Attention
Control panel overlay Sample paper Printhead
(may be pre-installed) packs
10 10
Black and colour Power supply Software CD
ink cartridges and adaptor and brochure
Identify main components
Scanner glass
Memory card
Printer access
slots
door
Memory card
light
Output tray
USB drive/
Paper-width
PictBridge port
guide
Photo tray light
Main tray
Photo tray
Paper-length
guide
Control panel
Scanner lid
Rear access
USB port
door
Power connector
*1K1194* *E*
*1K1194* *E*
1K1198 E
7
Install Windows Software
IMPORTANT: Do not connect the USB cable to the printer until
instructed during software installation.
a) Load the Kodak EasyShare
CD into the CD-ROM drive.
If instructions do not appear,
click Start, then Run. Select
CD-ROM drive and type
setup.exe, then press ENTER.
b) If connected to the Internet,
select Web Install to get the
latest upgrades for your
printer.
c) Follow the on screen prompts
to install the AiO software.
d) Connect the printer to
the USB port. Click Next
and follow the on screen
prompts.
If prompted, re-boot your
computer.
e) When the EasyShare AiO dialog box appears, close the window.
Vista XP
Eastman Kodak Company
Rochester, NY 14650 U.S.A.
© Eastman Kodak Company, 2007
MC/MR/TM: Kodak, EasyShare.
Unpack printer
IMPORTANT: Do not connect the USB cable to the printer until
instructed during software installation.
a) See box flaps for unpacking
instructions.
b) Remove all orange shipping
tape from the printer.
1
Install control panel
a) If not pre-installed, insert
the control panel overlay,
bottom end first.
b) Press down on all edges of
the overlay until it snaps
into position.
2
Load paper
a) Load photo paper into the photo tray.
1) Lift the photo tray lid. Insert
the photo paper glossy side
down.
IMPORTANT: Do not overload
the photo tray. Max 20 sheets.
2) Push the photo tray in
until it clicks into place.
NOTE: You can only print to
the photo tray when the photo
tray is pushed in.
3) Lower the photo tray lid.
b) Load plain white paper into the main tray.
1) 2)
3) 4)
Install Macintosh software
a) Connect the USB cable to
the printer and your
computer.
b) Download the EasyShare
AiO software from
www.kodak.com/go/5300aiosupport.
c) Double-click the .dmg file to
open it.
d) Wait for the Kodak EasyShare
Installer icon to appear on your
desktop and double-click on it.
e) Click on the
Install Software.app
icon and follow
the on-screen prompts.
The Bluetooth® trade marks are
Windows® is a registered trade mark
owned by the Bluetooth SIG, Inc. of Microsoft Corporation
Macintosh® is a registered
Printed in the U.S.A.
trade mark of Apple Computer, Inc.
3
4
Install printhead
IMPORTANT: The printhead
is fragile. Handle carefully.
a) Lift the printer access door.
Make sure the orange tape
is removed from the carriage.
b) Remove the printhead from
its bag.
IMPORTANT: Insert the
printhead immediately
upon opening sealed bag.
c) Pull on the orange tab to
remove the protective
retainer.
d) Carefully remove and discard
the clear plastic shield and the
orange protective cap.
IMPORTANT: Do not touch
the copper-coloured contacts.
e) Place the printhead into
the carriage. Insert at the
angle shown.
f) Push firmly against the top
of the white label on the
printhead until it clicks into
place.
Tip: The printhead requires a
firm push and makes an audible
click when locked into place.
Helpful tips
Pull out the output tray extender
to help collect your 216 x 297 mm
(8.5 x 11.7") prints.
The photo tray light illuminates
when the photo tray is pushed in.
To use the main paper tray,
disengage the photo tray by
pulling it towards you.
Control panel features
Displays photos, messages, status
and menus
Rotates the picture on the display
EasyShare 5300
Zooms in or out in .05X increments
All-in-One Printer
Transfers images from a device
connected to a USB host port, PictBridge
Rotate Zoom Proofsheet Transfer or Picture Transfer Protocol (PTP)
Photo
Scan Copy
Displays the proofsheet menu when
there are pictures on an inserted memory
Menu Help card or connected USB host device
OK
Cancel On/Off
Displays the Help menu on the LCD
screen
Attention
Displays the Main menu on the LCD
screen
Indicates attention is needed. When
illuminated, see LCD screen for further
instruction
Getting started
You can access and use the AiO Home Centre by double-clicking on the
icon on your desktop.
Windows Macintosh
The AiO Home Centre will enable The AiO Home Centre will enable
you to copy, scan and configure you to configure your AiO printer
your AiO printer from the from the computer. You can also
computer. You can also launch order supplies and launch Kodak
Kodak EasyShare software for EasyShare software for
transferring, viewing and working transferring, viewing and working
with your digital pictures and with your digital pictures and
videos. videos. Use the Kodak EasyShare
AiO drivers to print and scan to
your AiO printer.
5
Install ink cartridges
a) Remove the black ink
cartridge from its bag.
IMPORTANT: Insert ink
cartridges immediately
upon opening sealed bag.
b) Carefully remove and
discard the orange cap.
Handle ink cartridges
carefully to avoid ink
transfer.
6
c) Insert the black ink
cartridge into the
printhead.
d) Press down on the ink
cartridge until you hear
it click into position.
e) Open and uncap the colour
ink cartridge. Insert it into
the printhead.
f) Press down firmly on the
ink cartridge until you
hear it click into position.
It is normal for the printhead
to flex when inserting the
cartridge. You will not
damage the printer.
g) Close the printer access door.
Troubleshooting
If you have additional questions about troubleshooting this device, please
visit www.kodak.com/go/5300aiosupport
PROBLEM:
I cannot get a calibration sheet to print.
SOLUTION:
Where necessary, you can force a calibration sheet to print by following these
steps:
1. Press Menu, select Calibrate Printer and press OK.
2. Select Print Calibration Page and press OK.
3. When the print comes out, place it at the front, right corner of the scanner
glass.
4. Close the scanner lid and press START.
PROBLEM:
I cannot print to my desired paper type.
SOLUTION:
Check to see if the photo tray is pushed in. You can do this by checking if the
green photo tray light is illuminated. If it is, all prints will be produced from
this tray. If you want to print from the main tray, pull out the photo tray by
lifting the photo tray lid and sliding the paper tray towards you (see step 6d).
PROBLEM:
I have a paper jam.
SOLUTION:
1. Press in the tabs on the rear access door to remove the door.
2. Gently pull the paper out of the rollers.
IMPORTANT: If the paper tears while removing it, check inside the
printer for torn pieces of paper and remove them. Additional jams are
likely to occur if all of the torn pieces are not removed.
3. Replace the rear access door. Gently push the door forwards until it snaps
into place.
Is further troubleshooting required?
If you need further information to help answer your questions, please contact
Technical Support and have your KSN number ready. Your KSN number can
be found on the unit after lifting the printer access door as shown.
KODAK SERVICE NUMBER
F330065
*F330065*
*F330065*
Connect power
a) Connect the power supply
and adaptor.
b) Remove the plastic film from the LCD
display. Position the LCD display
and press ON.
Calibrate printer
IMPORTANT: Make sure that the photo tray is pushed in. The photo
tray light should be lit.
a) Press Start. Wait two minutes
for the calibration sheet to print.
Tip: If the calibration sheet
does not print properly, see
the Troubleshooting section
in this set-up poster.
b) Remove the calibration sheet
from the output tray. Place it
face down and align to the front,
right corner of the scanner glass,
as shown.
IMPORTANT: The blue arrow in the corner of the calibration sheet
must point to the registration marks as shown.
4x6
c) Lower the scanner lid and
press Start. The ON/OFF
4x6
light will turn solid green
when the calibration is complete.
Remove the sheet from the
scanner glass.
d) Lift the photo tray lid, then slide the
photo tray towards you to return to
main tray operation. The photo tray
light will turn off.
More accessories
More options
More convenience
The KODAK EasyShare All-in-One Printer gives you more. Be sure to visit
our online store to select from our full line of supplies and accessories at
www.kodak.com/go/AiO.
Kodak's inkjet photo paper
Get prints that look great the first
time with Kodak's unique backprint
technology that automatically
enables optimised prints.
Value packs
Save up to 50% on everything you
print and pay as little as 7p per print
with our ink and paper value packs.
Two-sided printing accessory
It's easy to print both sides of your
document with the Kodak EasyShare
5000 Series two-sided printing
accessory.
Wireless adaptor
Go wireless with the Kodak wireless
2.0 USB Bluetooth adaptor.
Wireless 2.0 USB
Bluetooth adaptor
Note: A USB 2.0 cable is required to connect your Kodak All-in-One printer
to your Windows or Macintosh OS computer. Available in the Kodak online
store or see your local retailer.
Need more help?
Look here for answers:
www.kodak.com/go/5300aiosupport
User guide
The User Guide is installed with your Kodak AiO software and is located:
Windows
Start All Programs Kodak
Macintosh
Library Documentation Kodak AiO Printers