Outputting Color Bars; Others - JVC GY-HD110U Instructions Manual

FEATURES OF THE CAMERA SECTION

Outputting color bars

FULL AUTO
switch
USER button
88
This camcorder can output three types of color bars, depend-
ing on the camera settings.
NTSC standard : Outputs color bars compliant with the
SMPTE standard.
PAL standard : Outputs color bars compliant with the
EBU standard.
16:9 screen : Outputs multi-format color bars.
To output color bars, make the following settings.
1.
Turn the FULL AUTO switch to "OFF".
2.
Set the BARS item on the CAMERA OPERATION menu
screen to "ON". X See page 66.
• Color bars are output.
Outputting color bars using the USER buttons
1.
Turn the FULL AUTO switch to "OFF".
2.
Assign "BARS" to one of the USER1, 2 or 3 buttons.
X See "SWITCH MODE Menu Screen" on page 71.
3.
Press the USER button to which "BARS" was assigned.
• Color bars are output.
MEMO
• You can select whether to output an audio test signal dur-
ing color bar output using the TEST TONE item on the
AUDIO/MIC [1/2] menu screen. X See page 72.
• Color bars are not output when FULL AUTO mode is ON
or in VTR mode.

OTHERS

Warnings and Responses
Warnings are displayed on the LCD monitor or the viewfinder if there was a mistaken operation, if the battery or tape is low, or if
there is a problem on the VTR.
In addition, if the tape or battery is low or the VTR has a problem, the tally lamp flashes (or lights) and an alarm is output from the
monitor speaker or PHONES jack.
MEMO
This camcorder uses microcomputers. It may not operate properly if there is external static or interference. If this happens, turn
the power off and then on again.
Display Status
60/30 24 INHIBIT The FRAME RATE item is set to 50/25, and a tape record-
CHANGE FRAME ed in 60/30, 24 frame HDV format is played back or it is in-
RATE MENU put into the IEEE1394 port in VTR mode.
60/30 INHIBIT The FRAME RATE item is set to 50/25, and a tape record-
CHANGE FRAME ed in 60/30 frame DV format is played back or it is input into
RATE MENU the IEEE1394 port in VTR mode.
50/25 INHIBIT The FRAME RATE item is set to 60/30 or 24, and a tape re-
CHANGE FRAME corded in 50/25 frame HDV/DV format or it is input into the
RATE MENU IEEE1394 port in VTR mode.
24 INHIBIT CHANGE The FRAME RATE item is set to 50/25 and, a tape record-
FRAME RATE MENU ed in 24 frame DV format is played back or it is input into
the IEEE1394 port in VTR mode.
DV-60I INVALID! A tape recorded in DV-60I, DV-24P, or DV-24PA format
DV-24P INVALID! was played back or input into the IEEE1394 connector in
DV-24PA INVALID! VTR mode on the E model.
DV-50I INVALID! A tape recorded in DV-50I or DV-25P format was played
DV-25P INVALID! back or input into the IEEE1394 connector in VTR mode on
the U model.
INVALID TAPE! A computer data tape or a DVC PRO cassette was used.
LP TAPE INVALID!* Tried to play back a tape recorded in LP mode.
NO DV SIGNAL* DV signal was not input.
NO HDV SIGNAL* HDV signal was not input.
COPY INHIBIT* Tried to record a copyguarded signal.
REC INHIBIT* A tape that cannot be recorded (back switch is set to SAVE)
was inserted.
NO TAPE* No videocassette tape is inserted.
LOW VOLTAGE* Battery is low.
TAPE NEAR END* There are less than 3 minutes remaining on the tape (flash-
es only when recording).
TAPE END* Displayed when the tape ends.
CHANGE 1394 Recording or playback video format and the IEEE1394 set-
SWITCH* ting is different when connected to the IEEE1394 port.
SWITCH TO VTR Tried to use the FF or REW button in camera mode.
MODE*
HEAD CLEANING Displayed when the video head is dirty. (Head clogging was
REQUIRED detected during an edit search in shooting mode as well as
during playback and displayed.)
CLEANING TAPE! Displayed when a head cleaning tape is inserted.
COPY GUARD!* Tried to play back a copyguarded tape.
FAN MOTOR HOUR Over the prescribed fan motor usage time.
PUSH CASSETTE The videocassette cover is not firmly shut.
COVER*
* When status indications are magnified, warnings are not displayed on the LCD monitor.
X See "Magnified Status Indications on the LCD Monitor" on page 26.
Action
Sets the FRAME RATE item on the VIDEO FORMAT menu
screen to match the frames.
X See page 64.
The E model cannot play back tapes recorded in DV-60I,
DV-24P or DV-24PA format or input into the IEEE1394 con-
nector in VTR mode.
The U model cannot play back tapes recorded in DV-50I or
DV-25P format or input into the IEEE1394 connector in
VTR mode.
Use a MiniDV videocassette.
This camcorder cannot record or play back in LP mode.
Set the IEEE1394 switch to DV and input a DV signal.
Set the IEEE1394 switch to HDV and input an HDV signal.
Cannot record a copyguarded signal.
Set the switch on the back of the cassette tape to REC.
Insert a cassette tape.
Charge the battery pack or replace it.
To continue shooting, find a new tape or replace the tape.
Replace the tape.
Set the IEEE1394 switch correctly, turn the power off and
then on again.
Press the CAM/VTR button to set VTR mode.
Clean with a special head cleaning tape.
X See page 7.
The display disappears when the head cleaning tape is re-
moved.
Cannot play back a copyguarded tape.
Please contact your local dealer or JVC.
Lightly push the top center of the videocassette cover.
89