CONTENTS Warming drawer Coffee maker Speed oven Safety and warnings Safety and warnings Safety and warnings Parts supplied Parts supplied Prior to installation Prior to installation Prior to installation After installation Product dimensions After installation Product dimensions 5A Cabinetry dimensions – underbench Product dimensions 5A Cabinetry dimensions (ie installed with F&P single oven)
SAFETY AND WARNINGS WARNING! The electrical outlet should be easily accessible after installation. ● When a companion product is installed in combination with the warming drawer to ● Electrical Shock Hazard the same circuit, operating both products may cause an overload. If in doubt consult a Before carrying out any work on the electrical section of the appliance, qualified electrician.
PARTS SUPPLIED Screws (4) Anti-tip bracket (1) Oven support brackets (2) PRIOR TO INSTALLATION The cavity is square and level, and of the required dimensions. ● The installation will comply with all clearance requirements and applicable standards and regulations. ● The power switch will be easily accessible to the customer when the warming drawer is installed.
THE FOLLOWING PAGES DETAIL COMMON CABINETRY SCENARIOS CABINETRY DIMENSIONS – UNDERBENCH (ie INSTALLED WITH F&P SINGLE OVEN) Oven support Oven brackets 28 3/8" Oven (720mm) Warming drawer PLAN Warming drawer Fit the supplied oven support brackets SIDE Unscrew-fit- rescrew Oven support bracket CABINETRY DIMENSIONS inches (mm) Minimum inside height of cavity...
CABINETRY DIMENSIONS – WALL MOUNTED (ie INSTALLED WITH A F&P COMPACT OVEN) Compact oven Warming drawer 23 5/8" Compact oven (600mm) PLAN SIDE Warming drawer Compact oven Lower trim kit (optional, supplied separately) Warming drawer IMPORTANT! Additional 11/16" (18mm) Wood Spacer In a wall mounted installation, there needs to be an Cabinet below...
CABINETRY DIMENSIONS – WALL MOUNTED (ie INSTALLED WITH A F&P COFFEE MAKER) IMPORTANT! If installing under the F&P Coffee Maker, ensure there is the 2" (50mm) gap at the back of the cabinet and the 7 7/8" (200mm ) toekick cutout required for airflow. Refer to the Coffee Maker Install instructions.
CABINETRY DIMENSIONS – WALL MOUNTED (STANDALONE) Supplied anti-tip bracket (screwed to the back wall) IMPORTANT! In a standalone wall mounted installation, you must ensure that the supplied anti-tip bracket is installed unless there is a fixed shelf above acting as an anti-tip obstacle. Fixed shelf Steam oven 4 3/4"...
DISCARD PACKAGING RESPONSIBLY Unpack the warming drawer and inspect for any signs of damage. Do not install the warming drawer if it has been damaged. IMPORTANT! Packing materials (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools should not be left around during and after installation, especially if they are within easy reach of children, as they may cause serious injuries.
SECURE THE WARMING DRAWER TO THE CABINETRY 1 Ensure the warming drawer is level and positioned in place in the cavity. IMPORTANT! Do not lift the warming drawer by the drawer handle. 2 Fully open the drawer. 3 Fasten the warming drawer in place with the two screws supplied, through the front trim, beneath the drawer.
FINAL CHECKLIST FP WARMER DRAWER INTERFACE LOGIC_V1 TO BE COMPLETED BY THE INSTALLER Make sure the warming drawer is level and securely fitted to the cabinetry. P WARMER DRAWER INTERFACE LOGIC_V1 FP WARMER DRAWER INTERFACE LOGIC_V1 Make sure any internal packaging has been removed from the drawer. PRODUCT OFF USER PRESSES ON/OFF BUTTON Make sure that the isolating switch is accessible by the customer.
SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS! To protect against fire, electric shock and injury to persons do not submerge the cord or ● plugs in water or other liquids. Installation To reduce the risk of injury, do not drape cord over the counter top or table top where it ●...
PARTS SUPPLIED Screws Rails (2) Clip (1) (28) Spacers (4) for side (4) for bottom PRIOR TO INSTALLATION The countertop and coffee maker cavity are square and level, and are the required dimensions. ● The installation will comply with all clearance requirements and applicable standards and regulations. 560.00 ●...
CABINETRY DIMENSIONS (18 1/8" (460mm) HIGH CAVITY) Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets. IMPORTANT! 5/8–13/16"...
CABINETRY DIMENSIONS (18 7/8" (480mm) CAVITY TRIM KIT) Verify the minimum measurements required for correct installation of the appliance. The coffee maker must be installed in a column and the column must be firmly fixed to the wall with commercially available brackets. Lower Trim Kit The Lower Trim kit shown is available to order separately from fisherpaykel.com.
INSTALLATION INSTRUCTIONS approx. 13 3/4" (350mm) Position the rails on the sides of the cabinet. Fix with the screws provided, then extract Fix the power cable with the clip. The power cable must be long enough to allow them completely. the appliance to be extracted from the cabinet to fill the coffee bean container.
CONNECT THE WARMING DRAWER TO THE MAINS SUPPLY IMPORTANT! All electrical work may only be carried out by suitably qualified and competent persons in accordance with national and local safety regulations. ● This warming drawer must be grounded. ● Before placing the coffee maker into the cavity, route the power cord into the back of the cavity and plug it in to the switched socket. The switched socket should be in an easily accessible area within 35 7/16"...
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Make sure the coffee maker is level and securely fitted to the cabinetry. Check the lower trim is undamaged. Check there is adequate clearance. This is to ensure correct air circulation. Make sure any cable ties and internal packaging has been removed from the coffee maker cavity. Make sure all coffee maker vents and openings are clear and free of any obstruction or damage.
SAFETY AND WARNINGS Installation If the installation requires alterations to the domestic electrical system, call a qualified ● electrician. The electrician should also check that the socket cable section is suitable WARNING! for the electricity drawn by the oven. The oven must be grounded. ●...
PRIOR TO INSTALLATION The countertop and oven cavity are square and level, and are the required dimensions. ● 560.00 The installation will comply with all clearance requirements and applicable standards and regulations. ● The isolating switch will be easily accessible to the customer with the oven installed. ●...
ELECTRICAL HOOK-UP Before connecting to the electricity, make sure that the: specifications of the electrical system match with what is detailed on this section. (Fig. 1) ● system has an effective ground connection compliant with current standards and laws. ● The ground connection is required by law.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Make sure the oven is level and securely fitted to the cabinetry. Check the lower trim is undamaged. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation.
SAFETY AND WARNINGS Installation If the installation requires alterations to the domestic electrical system, call a qualified ● electrician. The electrician should also check that the socket cable section is suitable WARNING! for the electricity drawn by the oven. The oven must be grounded. ●...
PRIOR TO INSTALLATION The countertop and oven cavity are square and level, and are the required dimensions. ● 560.00 The installation will comply with all clearance requirements and applicable standards and regulations. ● The isolating switch will be easily accessible to the customer with the oven installed. ●...
CABINETRY DIMENSIONS (18 1/8" (460mm) HIGH CAVITY) The oven can be installed under a cooktop, in a column, or combined with the companion warmer drawer. ● The cabinet material must be able to withstand heat. ● The oven must be centered within the walls of the cabinet and fixed with the screws and bushings that are provided. ●...
CABINETRY DIMENSIONS (18 7/8" (480mm) CAVITY TRIM KIT) The oven must be installed under a cook top, in a column, or combined with the companion warmer drawer. ● The cabinet material must be able to withstand heat. ● The oven must be centred within the walls of the cabinet and fixed with the screws and bushings that are provided. ●...
ELECTRICAL HOOK-UP Before connecting to the electricity, make sure that the: specifications of the electrical system match with what is detailed on this section. (Fig. 1) ● system has an effective ground connection compliant with current standards and laws. ● The ground connection is required by law.
FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Make sure the oven is level and securely fitted to the cabinetry. Check the lower trim is undamaged. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation.
Page 39
PRODUITS COMPAGNONS Modèles Tiroir chauffant WB24 Machine à café EB24 Four à vapeur OS24N Four à micro-ondes OM24N GUIDE D’INSTALLATION US CA 591496F 08.20...
Page 40
TABLE DES MATIÈRES Tiroir chauffant Machine à café Four à micro-ondes Sécurité et avertissements Sécurité et avertissements Sécurité et avertissements Pièces fournies Pièces fournies Avant l’installation Avant l’installation Avant l’installation 3 Après l’installation Dimensions du produit Après l’installation 4 Dimensions du Produit 5A Dimensions de l’armoire –...
SÉCURITÉ ET AVERTISSEMENTS Avant l’installation, assurez-vous que la tension et la fréquence indiquées sur la plaque AVERTISSEMENT! ● signalétique correspondent à l’alimentation électrique domestique. La prise électrique doit être facilement accessible après l’installation. ● Danger de choc électrique Lorsqu’un produit complémentaire est installé en même temps que le tiroir chauffant sur le ●...
PIÈCES FOURNIES Des vis (4) Support anti-basculement (1) Supports de support de four (2) AVANT L’INSTALLATION La cavité est carrée et de niveau, et des dimensions requises. ● L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. ●...
DIMENSIONS DU PRODUIT AVANT LE CÔTÉ Bornier MODÈLE MODÈLE WB24SDEB WB24SDEX DIMENSIONS DU PRODUIT Pouces (mm) Pouces (mm) Hauteur totale du produit 4 5/8" (118) 4 5/8" (118) Largeur totale du produit 23 1/2" (596) 23 1/2" (596) Profondeur du panneau avant du tiroir (à l’exclusion de la poignée)* 13/16"...
LES PAGES SUIVANTES DÉTAIL SCÉNARIOS D’ARMOIRES COMMUNES DIMENSIONS DE L’ARMOIRE – UNDERBENCH (ie INSTALLÉ AVEC F&P FOUR UNIQUE) Supports de Four support de four 28 3/8" Four (720mm) Tiroir chauffant HAUT Tiroir chauffant Monter les supports de four fournis Attache LE CÔTÉ...
DIMENSIONS DE L’ARMOIRE – MURAL (ie INSTALLÉ AVEC UN FOUR COMPACT F&P) Four compact Tiroir chauffant 23 5/8" Four compact (600mm) HAUT LE CÔTÉ Tiroir chauffant Four compact Trousse de garniture inférieure (en option, fournie séparément) Tiroir chauffant IMPORTANT! Espaceur de bois supplémentaire de 11/16"...
DIMENSIONS DE L’ARMOIRE – MURAL (ie INSTALLÉ AVEC UNE CAFETIÈRE F&P) IMPORTANT! Si vous installez sous la cafetière F&P, assurez-vous qu’il y a un espace de 2"(50mm) à l’arrière de l’armoire et une découpe de 7 7/8" (200mm ) pour le passage de l’air. Reportez-vous aux instructions d’installation du fabricant de café.
DIMENSIONS DE L’ARMOIRE – MURAL (STANDALONE) Support anti-basculement fourni (vissé sur la paroi arrière) IMPORTANT! Dans une installation murale autonome, vous devez vous assurer que le support antibasculement fourni est installé à moins qu’une étagère fixe agisse au-dessus comme un obstacle anti-basculement. Tablette fixe Four à...
JETER L’EMBALLAGE DE MANIÈRE RESPONSABLE Déballez le tiroir chauffant et inspectez pour déceler tout signe de dommage. N’installez pas le tiroir chauffant s’il a été endommagé. IMPORTANT! Les matériaux d’emballage (sacs en plastique, mousse de polystyrène, agrafes, sangles d’emballage, etc.) et les outils ne doivent pas être laissés en place pendant et après l’installation, surtout s’ils sont facilement accessibles aux enfants, car ils peuvent causer des blessures graves.
FIXEZ LE TIROIR CHAUFFANT AUX ARMOIRES 1 Assurez-vous que le tiroir chauffant est de niveau et positionné dans la cavité. IMPORTANT! Ne soulevez pas le tiroir chauffant par la poignée du tiroir. 2 Ouvrez complètement le tiroir. 3 Fixez le tiroir chauffant en place avec les deux vis fournies, à travers la garniture avant, sous le tiroir.
LISTE DE CONTRÔLE FINALE FP WARMER DRAWER INTERFACE LOGIC_V1 A REMPLIR PAR L’INSTALLATEUR Assurez-vous que le tiroir-réchaud est de niveau et solidement fixé aux armoires. FP WARMER DRAWER INTERFACE LOGIC_V1 FP WARMER DRAWER INTERFACE LOGIC_V1 Assurez-vous que tout emballage interne a été retiré du tiroir. PRODUCT OFF USER PRESSES ON/OFF BUTTON Assurez-vous que l’interrupteur d’isolement est accessible au client.
SÉCURITÉ ET AVERTISSEMENTS CONSIGNES DE SÉCURITÉ IMPORTANTES! Si la machine est installée en combinaison avec d’autres appareils, une base de ● protection doit être installée entre l’appareil et l’appareil. Ne pas installer ou utiliser à l’extérieur même s’il est installé dans la vitrine. ●...
PIÈCES FOURNIES Des vis Rails (2) Agrafe (1) (28) Espaceurs (4) pour le côté (4) pour le bas AVANT L’INSTALLATION La cavité du comptoir et de la cafetière sont carrées et de niveau, et sont les dimensions requises. ● 560.00 L’installation sera conforme à...
DIMENSIONS DU PRODUIT LE CÔTÉ HAUT MODÈLES EB24 DIMENSIONS DU PRODUIT Pouces (mm) Hauteur totale du produit 18" (458) Largeur totale du produit 23 1/2" (596) Profondeur totale du produ 18 7/8" (480) it (à l’exclusion des cadrans) Hauteur du châssis 17 1/2"...
DIMENSIONS DE L’ARMOIRE (CAVITÉ DE 18 1/8" (460MM) DE HAUTEUR) Vérifiez les mesures minimales requises pour une installation correcte de l’appareil. La cafetière doit être installée dans une colonne et la colonne doit être fermement fixée au mur avec des supports disponibles dans le commerce. IMPORTANT! 5/8–13/16"...
DIMENSIONS DE L’ARMOIRE (KIT DE GARNITURE DE CAVITÉ DE 18 7/8" (480MM)) Vérifiez les mesures minimales requises pour une installation correcte de l’appareil. La cafetière doit être installée dans une colonne et la colonne doit être fermement fixée au mur avec des supports disponibles dans le commerce. Trousse de garniture inférieure Le kit Lower Trim montré...
INSTRUCTIONS D’INSTALLATION environ 13 3/4" (350mm) Positionnez les rails sur les côtés de l’armoire. Fixer avec les vis fournies, puis les extraire Fixez le câble d’alimentation avec le clip. Le câble d’alimentation doit être suffisamment complètement. long pour permettre à l’appareil d’être extrait de l’armoire pour remplir le conteneur de Si la cafetière est installée sur un tiroir chauffant, utilisez la surface supérieure comme grains de café.
LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR Assurez-vous que la cafetière est de niveau et solidement fixée aux armoires. Vérifiez que la garniture inférieure n’est pas endommagée. Vérifiez qu’il y a un dégagement suffisant. Ceci afin d’assurer une circulation d’air correcte. Assurez-vous que les attaches de câble et l’emballage interne ont été...
SÉCURITÉ ET AVERTISSEMENTS Installation Si l’installation nécessite des modifications du système électrique domestique, appelez un ● électricien qualifié. L’électricien doit également vérifier que la section du câble de prise est AVERTISSEMENT! adaptée à l’électricité tirée par le four. Le four doit être mis à la terre. ●...
AVANT L’INSTALLATION Le comptoir et la cavité du four sont carrés et de niveau, et sont les dimensions requises. ● 560.00 L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. ● L’interrupteur d’isolement sera facilement accessible au client avec le four installé. ●...
DIMENSIONS DU PRODUIT HAUT LE CÔTÉ MODÈLES OS24N DIMENSIONS DU PRODUIT Pouces (mm) Hauteur totale du produit 18" (458) Largeur totale du produit 23 7/16" (596) Profondeur totale du produit (à l’exclusion de la poignée et des cadrans) 22 1/8" (562) Hauteur du châssis...
5/8–13/16" FLUSH INSTALLER (16–20mm) 7/8" (22mm) min 1/16" (2mm) LE CÔTÉ HAUT MODÈLES OS24N CABINETRY DIMENSIONS Pouces (mm) Largeur intérieure minimale de la cavité 22 1/16" (560) Largeur totale des armoires 23 5/8" (600) Hauteur intérieure minimale de la cavité...
7/8" (22mm) Trousse de min 1/16" (2mm) LE CÔTÉ HAUT garniture inférieure MODÈLES OS24N CABINETRY DIMENSIONS Pouces (mm) Largeur intérieure minimale de la cavité 22 1/16" (560) Largeur totale des armoires 23 5/8" (600) Hauteur intérieure minimale de la cavité...
BRANCHEMENT ÉLECTRIQUE Avant de vous connecter à l’électricité, assurez-vous que: les spécifications du système électrique correspondent à ce qui est détaillé sur cette section. (Fig. 1) ● le système a une connexion au sol efficace conforme aux normes et lois en vigueur. ●...
LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR Assurez-vous que le four est de niveau et solidement fixé aux armoires. Vérifiez que la garniture inférieure n’est pas endommagée. Ouvrez lentement la porte du four jusqu’à ce qu’elle soit complètement ouverte et vérifiez qu’il y a un espace suffisant entre le bas de la porte et la garniture inférieure. Ceci afin d’assurer une circulation d’air correcte.
SÉCURITÉ ET AVERTISSEMENTS Installation Si l’installation nécessite des modifications du système électrique domestique, appelez un ● électricien qualifié. L’électricien doit également vérifier que la section du câble de prise est AVERTISSEMENT! adaptée à l’électricité tirée par le four. Le four doit être mis à la terre. ●...
AVANT L’INSTALLATION Le comptoir et la cavité du four sont carrés et de niveau, et sont les dimensions requises. ● 560.00 L’installation sera conforme à toutes les exigences de dégagement et aux normes et règlements applicables. ● L’interrupteur d’isolement sera facilement accessible au client avec le four installé. ●...
DIMENSIONS DU PRODUIT HAUT LE CÔTÉ MODÈLES OM24N DIMENSIONS DU PRODUIT Pouces (mm) Hauteur totale du produit 18" (458) Largeur totale du produit 23 7/16" (596) Profondeur totale du produit (à l’exclusion de la poignée et des cadrans) 22 1/8" (562) Hauteur du châssis 17 1/2"...
DIMENSIONS DE L’ARMOIRE (CAVITÉ DE 18 1/8" (460MM) DE HAUTEUR) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. ● Le matériau de l’armoire doit être capable de résister à la chaleur. ●...
DIMENSIONS DE L’ARMOIRE (KIT DE GARNITURE DE CAVITÉ DE 18 7/8" (480MM)) Le four doit être installé sous une table de cuisson, dans une colonne ou combiné avec le tiroir-réchaud. ● Le matériau de l’armoire doit être capable de résister à la chaleur. ●...
BRANCHEMENT ÉLECTRIQUE Avant de vous connecter à l’électricité, assurez-vous que: les spécifications du système électrique correspondent à ce qui est détaillé sur cette section. (Fig. 1) ● le système a une connexion au sol efficace conforme aux normes et lois en vigueur. ●...
LISTE DE CONTRÔLE FINALE A REMPLIR PAR L’INSTALLATEUR Assurez-vous que le four est de niveau et solidement fixé aux armoires. Vérifiez que la garniture inférieure n’est pas endommagée. Ouvrez lentement la porte du four jusqu’à ce qu’elle soit complètement ouverte et vérifiez qu’il y a un espace suffisant entre le bas de la porte et la garniture inférieure. Ceci afin d’assurer une circulation d’air correcte.