SAFETY AND WARNINGS IMPORTANT SAFETY INSTRUCTIONS READ AND SAVE THIS GUIDE WARNING! To avoid hazard, follow these instructions carefully before installing or using this appliance. WARNING! Electric Shock Hazard Please make this information available to the person installing the appliance—doing so could reduce your installation costs.
PRIOR TO INSTALLATION INSTALLATION MILESTONES Ensure that: Milestone indicator The oven cavity is square and level based on the required dimensions The installation will comply with all clearance requirements and applicable standards and These milestones represent areas throughout regulations that are pivotal to an optimal installation The isolating switch will be easily accessible to the customer with the oven installed outcome.
Page 4
COMPONENTS PARTS TOOLS Supplied Not supplied Screws (2) Metal side shelves Powered driver Cross-head screwdriver fixing nut (2)
PRODUCT DIMENSIONS POWER OUTLET LOCATION Product Dimensions inch a Overall height of oven B Overall width of oven 23 7/16 c Overall depth of oven (excludes handle and front metal trim) 22 1/4 d Depth of oven frame, control panel and door (excludes handle 13/16 and front trim) E Depth of chassis (includes terminal block)
CABINETRY DIMENSIONS PROUD INSTALL 5/8 -13/16" (16 -20mm) PROFILE PLAN FLUSH INSTALL 5/8 -13/16" OS24N (16 -20mm) CABINETRY DIMENSIONS INCHES A Minimum inside height of cavity 17 5/16 B Minimum inside width of cavity 22 1/16 C Minimum inside depth of cavity 21 5/8 D Overall height of cabinetry (cavity around front frame) 18 1/8...
Page 7
CHECK CAVITY UNPACK PRODUCT Do not lift or move the product using the handle. Keep all packing materials until the unit has been inspected. Inspect the product to ensure there is no shipping damage. If any damage is detected contact the dealer or retailer you brought the product from to report the Measure cavity dimensions.
Page 8
UNPACK PRODUCT REMOVE DOOR Remove all control panel packaging. The Open the door and remove all cable ties control panel can be moved manually as and packaging holding the oven shelves needed. Take care when handling. in place. Grip the shelves at the front, making Dispose responsibly.
CONNECT POWER THREE WIRE CONNECTION This oven must be connected to the mains power supply only by a suitably qualified person. This oven must be earthed. Connect the two black wires together with twist-on connectors and the Before connecting the oven to the mains power supply, check that: two red wires together with twist-on the domestic wiring system is suitable for the power drawn by the oven (as specified on the connectors.
CONNECT POWER THREE WIRE CONNECTION FOUR WIRE CONNECTION If local codes permit connecting the cabinet-grounding conductor to the neutral (white) wire in junction box. Disconnect the power supply and remove the junction box cover. Connect the factory-taped gree and white oven wires to the neutral (white) wire in the junction box.
Page 11
CONNECT POWER POSITION OVEN INTO CAVITY FOUR WIRE CONNECTION Some models only*: For dark cabinetry, the supplied trim can be used to enhance clashing finish. Seperate the green and white oven cable wires. Connect the white oven cable wire To install, remove the trim adhesive and to the neutral (white) wire in junction press to secure to cavity.
Page 12
REFIT DOOR ALIGN AND SECURE Align oven with surrounding cabinetry Holding the door on both sides, carefully and appliances. lift door back onto the hinges. Open the door fully and push each Using the product as a guide, pre-drill 2 locking lever down and lock into place.
Page 13
REFIT SHELVES TEST OVEN Sliding shelves Follow the guidance on screen to ensure Place shelves back into the oven at the desired oven turns on and heats correctly. level. Refer to your User Guide for more Ensure shelves are level and correctly information.
INSTALLER CHECKLIST TO BE COMPLETED BY THE INSTALLER Ensure the oven is level and securely fitted to the cabinetry. Open the oven door slowly until it is fully open and check there is adequate clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation.