Generac Power Systems PWRmanager Owner's Manual
  1. Manuals
  2. Brands
  3. Generac Power Systems Manuals
  4. Controller
  5. PWRmanager
  6. Owner's manual

Generac Power Systems PWRmanager Owner's Manual

12 relay load controller
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Generac PWRmanager™ 12 Relay Load Controller
http://www.generac.com/service-support/product-support-lookup
Para español, visita:
Pour le français, visiter:
SAVE THIS MANUAL FOR FUTURE REFERENCE
Owner's Manual
Loss of life. This product is not intended to
be used in a critical life support application.
Failure to adhere to this warning could result
in death or serious injury.
Register your Generac product at:
https://pwrfleet.generac.com
Register your Generac product at:
WWW.GENERAC.COM
http://www.generac.com/service-support/product-support-lookup
WARNING
1-888-GENERAC
(888-436-3722)
1-888-GENERAC
(1-888-436-3722)
(000209b)
013469

Advertisement

Table of Contents
loading

Related Manuals for Generac Power Systems PWRmanager

Summary of Contents for Generac Power Systems PWRmanager

  • Page 1 Owner’s Manual Generac PWRmanager™ 12 Relay Load Controller 013469 WARNING Loss of life. This product is not intended to be used in a critical life support application. Failure to adhere to this warning could result in death or serious injury.
  • Page 2 When contacting an Independent Authorized Service Dealer (IASD) or Generac Customer Service, always supply the complete model number and serial number of the unit. Table 1: PWRmanager™ Important Information Unit Model Number Unit Serial Number Date Purchased Commissioning Date WARNING CANCER AND REPRODUCTIVE HARM www.P65Warnings.ca.gov. (000393a) Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 3: Table Of Contents

    Add or Delete a Circuit ..........8 Configure load priorities ..........8 Set Up or Adjust Home WiFi Account ......9 Local WiFi Connection ........9 Circuit Selection ..........9 Unmanaged ..............9 Automatic - Lockout .............9 Automatic - Managed ..........10 Installation Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 4 This page intentionally left blank. Installation Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 5: Section 1: Safety Rules & General Information

    NOTE blocks are used to alert personnel to special instructions about a particular operation that may be hazardous if performed incorrectly or carelessly. Observe them carefully. Alert definitions are as follows: Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 6: General Hazards

    Never work on this equipment while physically or mentally fatigued. • Any voltage measurements should be performed with a meter that meets UL3111 safety standards, and meets or exceeds overvoltage class CAT III. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 7: Section 2: General Information

    Grid State LED present, or the system is islanding. Selects to force all relays on, Mode Selector all relays off, or allow normal Knob operation. Keep in normal position at all times. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 8: Led Status

    Access Point (AP) mode broadcasting. Green Grid power is available. Unit is powered by grid. Grid State LED Blue Grid power is not available. Unit is powered by PWRcell system. Orange Grid status is unknown. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 9: Section 3: Operation

    Loads wired to connect through the PWRmanager during installation will appear in groups based on how they are Once the PWRmanager is registered, a new screen will currently controlled. be added in the app. To view that screen, tap on the Cir-...

  • Page 10: Navigation Bar

    Auto- Automatic matic - Managed circuits will be shed Managed based on priority order (lowest to high- est priority). Circuit will be on while grid connected. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 11: Connecting To Pwrmanager

    3-7. The landing page, with buttons, should appear. Once the mobile device has connected to the web inter- face for the PWRmanager and logged in, adjust the set- tings described in the following sections. Configuring PWRmanager 3-7. The PWRmanager should be configured Figure by the installer during installation.

  • Page 12: Add Or Delete A Circuit

    Add or Delete a Circuit These steps should be done by the installer as each cir- cuit is wired into the PWRmanager unit. If there is a need to delete these circuits, or have new ones added, contact the installer.

  • Page 13: Set Up Or Adjust Home Wifi Account

    PWRview app, and confirm that the panel and is maintained during outages. circuits list screen populates with information. NOTE: Even if the PWRmanager unit sheds all the loads Local WiFi Connection under its control, unmanaged loads will continue to draw power.

  • Page 14: Automatic - Managed

    Operation Automatic - Managed These loads are wired through the PWRmanager and are configured to run if they do not overload the inverter. If the total load exceeds the power capacity of the inverter, these will be shed in priority order to ensure the inverter continues to run.

  • Page 15: Section 4: Specifications

    Power Consumption <20 W Maximum Total Current 450 A Warranty 10 years Connectivity, Security Description Value WiFi Frequency Band 2.4 GHz IP Addressing DHCP, Static Encryption TLSv1.2 Compliance Description Value UL916 Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 16 Specifications This page intentionally left blank. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 17: Section 5: Troubleshooting Troubleshooting

    Serial Number Location When contacting Generac support during troubleshooting steps, provide the serial number for your PWRmanager. It is on the right side face of the unit as shown in the image below.

  • Page 18: Troubleshooting

    Reset breaker. If that doesn't fix the Breaker on one of the circuits is issue, contact installer or Generac App System Status is Circuit Error. tripped. support and note which circuit LED indicates error. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...

  • Page 19: Section 6: Dimensions And Drawings

    Dimensions and Drawings Section 6: Dimensions and Drawings Enclosure Base 013310 Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 20 Dimensions and Drawings This page intentionally left blank. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 21 Dimensions and Drawings This page intentionally left blank. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 22 Dimensions and Drawings This page intentionally left blank. Owner’s Manual for Generac PWRmanager 12 Relay Load Controller...
  • Page 24 ©2022 Generac Power Systems, Inc. S45 W29290 Hwy. 59 All rights reserved. Waukesha, WI 53189 Specifications are subject to change without notice. 1-888-GENERAC (1-888-436-3722) No reproduction allowed in any form without prior written www.generac.com consent from Generac Power Systems, Inc.

Table of Contents