Table of Contents
Advertisement
Rec during upload function
Clips recorded in the P2 card can be automatically transferred to a server device on the network during recording/playback with the camera.
The rec during upload function has the following two modes:
f Automatic transfer mode: After the rec during upload function is enabled, uploads recorded clips automatically in order.
f Manual selection mode: Uploads clips selected beforehand.
To use the rec during upload function, network settings and FTP client settings need to be configured beforehand.
Transferring recorded clips automatically (automatic transfer mode)
1
Establish the network connection between the camera and a server device.
Perform the setting referring to "FTP client function setting" (page 205).
2
Set the camera's main menu → [NETWORK SETUP] → [FTP CLIENT SERVICE] → [REC DURING UPLOAD] to [ENABLE].
3
Select the type of the clip to upload in the camera's main menu → [NETWORK SETUP] → [FTP CLIENT SERVICE] → [AUTO
UPLOAD].
[REC CLIP(PROXY)]: Upload target is proxy data of recorded clips.
[REC CLIP]: Upload target is recorded clips (main recording data and proxy data).
[DISABLE]: Recorded clips are not upload targets.
4
Shoot.
Clips are registered in the upload list immediately after recording is stopped, and then recorded clips are automatically transferred.
The viewfinder or LCD monitor shows the operation status of the rec during upload function. In addition, the thumbnail screen shows the operation
status of the rec during upload function and the transfer status of clips.
@
NOTE
t Uploading of the clip will start after the rec during upload function is enabled. To prevent the upload error, do not remove the card from the P2 memory
card slot and the microP2 memory card slot until the upload is completed.
t Up to 100 clips can be registered in the upload list for the upload of clips. Clips exceeding 100, excluding the uploaded clips and clips failed to upload
cannot be registered.
t While recording is stopped, you can add recorded clips to transfer. Select the clips to transfer by selecting the main menu → [CLIP] → [COPY] →
[FTP] or [FTP(PROXY)] from the thumbnail screen. The selected clips are registered in the upload list.
t Clips are also automatically transferred during recording, playback, and thumbnail display.
t The dividing unit of the recording files will become smaller when [SHORT SPLIT] is selected in the main menu → [RECORDING SETUP] → [FILE
SPLIT] while the rec during upload function is used, allowing to make the timing to start the clip transfer earlier while recording.
t If the network is disconnected during transfer, or the power of the camera is turned off and on again, transfer resumes in clip units.
The dividing unit of the recording files will become smaller when [SHORT SPLIT] is selected in the main menu → [RECORDING SETUP] → [FILE
SPLIT], making the number of clips to re-transfer reduced.
t Only the recorded clip in the slot 1 is automatically transferred during the simultaneous recording.
t Clips of interval recording, loop recording, one-clip recording, and one-shot recording are not automatically transferred.
t If the clip is recorded after selecting the main menu → [RECORDING SETUP] → [FILE SPLIT] → [ONE FILE], the clip that exceeds approximately
4 GB per file cannot be transferred to the FTP server.
t While the rec during upload function is enabled, the streaming function is disabled.
t The directory on the FTP server is not listed in the FTP explorer screen during the transmission or waiting to transmit the clips registered in the upload
list.
t The setting value in the main menu → [NETWORK SETUP] cannot be changed or initialized while the rec during upload function is set enabled.
t The copying between the P2 cards will not operate during the transmission or waiting to transmit the clips registered in the upload list.
t The clip delete function will not operate during the transmission or waiting to transmit the clips registered in the upload list.
t The format function of the P2 card will not operate during the transmission or waiting to transmit the clips registered in the upload list.
Transferring selected clips automatically (manual selection mode)
1
Establish the network connection between the camera and a server device.
Perform the setting referring to "FTP client function setting" (page 205).
2
Set the camera's main menu → [NETWORK SETUP] → [FTP CLIENT SERVICE] → [REC DURING UPLOAD] to [ENABLE].
Chapter 10 Network Connection — Rec during upload function
– 210 –
Fig. 1
Advertisement
Table of Contents
