Option Mode 2; Rec Function - Panasonic AJ-SPX900E Operating Instructions Manual

8-2-3 OPTION MODE 2

Items/ Adjustable
Data Saved Range
COMPONENT OFF
OUT BETACAM
M2
– C U F –
26PIN OFF
CONTROL BOTH
– C U F –
26PIN NORMAL
CONTROL SPECIAL
DEFAULT
– C U F –
Downloaded From CamcorderManual.com Panasonic Manuals
Remarks
Sets the analog component output level to
Triax, 26-pin extender, or external VTR.
OFF: Saves power and stops output.
However, when either a 26-pin
extender, external VTR or Triax is
connected, output automatically
switches to BETACAM level.
BETACAM:
Output using ß-CAM level.
M2: Output using M2 level.
Sets the recording control between the
external VTR and the AJ-SPX900E when a
26-pin camera adapter (AJ-CA905G,
optional) is attached and used with an
external VTR.
OFF: Recording is performed only with the
AJ-SPX900E, and not with the
external VTR.
BOTH:Recording is performed with both the
AJ-SPX900E, and an external VTR.
<Note>
The Tally Lamp indicates external VTR
status. Recording status of the AJ-SPX900E
can be selected in the menu option REC
TALLY of SYSTEM MODE.
Sets the type of VTR control signal (start/
stop recording) which is output from No. 12
of the 26-pin connector when the 26-pin
camera adapter (AJ-CA905G, optional) is
attached and controls an external VTR.
NORMAL:
Recording stop "LOW", recording start
"HIGH".
SPECIAL:
Recording stop "HIGH", recording start
"LOW".

8-2-4 REC FUNCTION

Items/ Adjustable
Data Saved Range
INTERVAL REC ON Sets INTERVAL REC function.
MODE ONE SHOT ON: Uses internal memory to perform
OFF
ONE SHOT:
Performs "one-shot" recording for the
duration specified under REC TIME, and
then stops.
OFF: INTERVAL REC is not performed.
<Note>
After the power is turned off, this setting
defaults to OFF when the power is next
turned on.
– – – F –
REC TIME 00s01f Set REC TIME (1 cut).
:
59s24f
– C U F –
PAUSE TIME 00h00m00s01f Specify PAUSE time for recording.
:
00h04m59s24f
:
23h59m59s24f
– C U F –
TAKE TOTAL NONE Specify the time needed for shooting.
Select from NONE (continue until operation
TIME :
is manually stopped) to 5 days.
5day
– C U F –
TOTAL REC 00m00s01f Display total recorded time. The setting
TIME : cannot be changed using this option.
Displays the recording time (recording time
99m59s24f
needed for the P2 card) calculated using
OVER100min
REC TIME, PAUSE TIME, and TAKE TOTAL
NONE
TIME.
– – – – –
AUDIO REC ON Select whether or not sound will be
OFF recorded.
– C U F –
START DELAY 0SEC Set the delay after pressing REC START to
start recording in INTERVAL REC.
:
10SEC
– C U F –
PRE REC TIME 0SEC Set PRE RECORDING.
0-15SEC:
:
15SEC
Set the length of time that can be
retrospectively recorded before the REC
START button is pressed.
<Note>
The maximum selectable range is 8 seconds
when the REC MODE in the <SYSTEM
MODE> screen is set to 50M (DVCPRO50).
– C U F –
LOOP REC ON Select whether or not to enable LOOP REC.
This setting can be used with PRE
MODE OFF
RECORDING features.
ON: Enable LOOP REC.
OFF: Disable LOOP REC.
<Note>
After the power is turned off, this item will
default to OFF the next time the power is
turned on.
– – – F –
The ____ in the Adjustable Range column indicates the preset
mode.
Remarks
interval recording.
8
101