Daikin Altherma EDLQ011-016CW1 Installer's Reference Manual page 104

6/9
Field settings table
Breadcrumb Field code Setting name
A.8 [4-00] What is the BUH operation mode?
A.8 [4-01] Which electric heater has priority?
A.8 [4-02] Below which outdoor temperature is heating allowed?
A.8 [4-03] Operation permission of the booster heater
A.8 [4-04] How to protect the water pipes from freezing
A.8 [4-05] --
A.8 [4-06]
-- (Do not change this value)
A.8 [4-07] Enable the second step of the backup heater?
A.8 [4-08] --
A.8 [4-09] --
A.8 [4-0A] --
A.8 [4-0B] Automatic cooling/heating changeover hysteresis.
A.8 [4-0D] Automatic cooling/heating changeover offset.
A.8 [4-0E] Is the installer on site?
A.8 [5-00] Is backup heater operation allowed above equilibrium temperature during space
heating operation?
A.8 [5-01] What is the equilibrium temperature for the building?
A.8 [5-02] Space heating priority.
A.8 [5-03] Space heating priority temperature.
A.8 [5-04] Set point correction for domestic hot water temperature
A.8 [5-05] --
A.8 [5-06] --
A.8 [5-07] --
A.8 [5-08] --
A.8 [5-09] --
A.8 [5-0A] --
A.8 [5-0B] --
A.8 [5-0C] --
A.8 [5-0D] What type of backup heater installation is used?
A.8 [5-0E] --
A.8 [6-00] The temperature difference determining the heat pump ON temperature.
A.8 [6-01] The temperature difference determining the heat pump OFF temperature.
A.8 [6-02] What is the capacity of the booster heater?
A.8 [6-03] What is the capacity of the backup heater step 1?
A.8 [6-04] What is the capacity of the backup heater step 2?
A.8 [6-05] --
A.8 [6-06] --
A.8 [6-07] --
A.8 [6-08] What is the hysteresis to be used in reheat mode
A.8 [6-09] --
A.8 [6-0A] What is the desired comfort storage temperature?
A.8 [6-0B] What is the desired eco storage temperature?
A.8 [6-0C] What is the desired reheat temperature?
A.8 [6-0D] What is the desired DHW production type?
A.8 [6-0E] What is the maximum temperature set point?
A.8 [7-00] Domestic hot water booster heater overshoot temperature
A.8 [7-01] Domestic hot water booster heater hysteresis
A.8 [7-02] How many leaving water temperature zones are there?
A.8 [7-03] --
A.8 [7-04] --
A.8 [7-05] Boiler efficiency
A.8 [8-00] --
4P522033-1 - 2018.01
Range, step
Default value
R/W 0~2
0: Disabled
1: Enabled
R/W 0~2
0: None
1: BSH
2: BUH
R/W 14~35°C, step: 1°C
35°C
R/W 0: Limited
1: No limit
2: Most optimum
3: Optimum
4: Only legionella
R/W
0: Continuous pump operation
1: Intermittent pump operation
2: No protection
0
0/1
R/W 0: No
1: Yes
0
1
0
R/W 1~10°C, step: 0,5°C
1°C
R/W 1~10°C, step: 0,5°C
3°C
R/W 0: No
1: Yes
R/W 0: Allowed
1: Not allowed
R/W -15~35°C, step: 1°C
-4°C
R/W 0: Disabled
1: Enabled
R/W -15~35°C, step: 1°C
0°C
R/W 0~20°C, step: 1°C
10°C
50
50
50
50
20
20
20
20
R/W 0~5
1: 1P,(1/1+2)
4: 3PN,(1/2)
5: 3PN,(1/1+2)
1
R/W 2~20°C, step: 1°C
2°C
R/W 0~10°C, step: 1°C
2°C
R/W 0~10 kW, step: 0,2 kW
3 kW
R/W 0~10 kW, step: 0,2 kW
3 kW
R/W 0~10 kW, step: 0,2 kW
0 kW
0
0
0
R/W 2~20⁰C, step: 1⁰C
10⁰C
0
R/W 30~[6-0E]⁰C, step: 1⁰C
55⁰C
R/W 30~min(50, [6-0E])⁰C, step: 1⁰C
45⁰C
R/W 30~min(50, [6-0E])⁰C, step: 1⁰C
45⁰C
R/W 0: Reheat only
1: Reheat + Scheduled
2: Scheduled only
R/W If [E-07]=0
40~75°C, step: 1°C
60°C
If [E-07]=5
40~80°C, step: 1°C
80°C
R/W 0~4⁰C, step: 1⁰C
0⁰C
R/W 2~40⁰C, step: 1⁰C
2⁰C
R/O
0: 1 LWT zone
1: 2 LWT zones
2.5
0
R/W 0: Very high
1: High
2: Medium
3: Low
4: Very low
1 min
Installer setting at variance with
default value
Date Value
(*1) *B*_(*2) *D*