Preparing Your Computer Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To protect them against damage from static electricity, you should follow some precautions whenever you work on your computer. 1. Unplug your computer when working on the inside.
Table of Content Chapter 1 Introduction ... 5 Features Summary ...5 8S651M-RZ Series Motherboard Layout ...7 Block Diagram ...8 Hardware Installation Process ...9 Step 1: Install the Central Processing Unit (CPU) ...9 Step 1-1: CPU Installation ...10 Step 1-2: CPU Cooling Fan Installation ...10 Step 2: Install memory modules ...
Chapter 1 Introduction Features Summary — Socket 478 for Intel — Support Intel — Intel Pentium — 2nd cache depends on CPU Chipset — North Bridge:SiS 651 — South Bridge:SiS 962L MuTIOL Media I/O Memory — 2 184-pin DDR sockets —...
Page 6
CPU, chipset and most of the peripherals. Whether your system can run under these specific bus frequencies properly will depend on your hardware configurations, including CPU, Chipsets, Mem ory, Cards… .etc. 8S651M-RZ Series Motherboard - 6 -...
Hardware Installation Process To set up your computer, you must complete the following steps: Step 1- Install the Central Processing Unit (CPU) Step 2- Install mem ory modules Step 3- Install expansion cards Step 4- Install I/O Peripherals cables Step 4 Step 4 Step 3 Step 1: Install the Central Processing Unit (CPU)
CPU and cooling fan. Figure 2. Fasten the cooling fan supporting-base onto the CPU socket on the motherboard. Figure 3. Make sure the CPU fan is plugged to the CPU fan connector, than install complete. 8S651M-RZ Series Motherboard - 10 -...
Step 2: Install memory modules Before installing the m emory modules, adhere to the following warning: 1. When DIMM LED is ON, do not install / remove DIMM from socket. 2. Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause improper installation.
OS vendor for possible patch or driver upgrade. For more inform ation please contact your OS or device(s) vendors. x Parallel port (LPT) Device like printer can be connected to Parallel port. y Serial port (COMA) Mouse and modem etc. can be connected to Serial port. "*" For 8S651M-RZ only. 8S651M-RZ Series Motherboard - 12 -...
z VGA port Monitor can be connected to VGA port. { Game/MIDI port This connector supports joystick, M IDI keyboard and other relate audio devices. | Line Out jack Connect the stereo speakers or earphone to this connector. } Line In jack Devices like CD-ROM , walkm an etc.
Page 14
Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating.The CPU fan connector supports Max. current up to 600 mA. 8S651M-RZ Series Motherboard Pin No. Definition Pin No. Definition 3.3V...
Page 15
4) SYS_FAN (System FAN Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. 5) IDE1/ IDE2(IDE1/IDE2 Connector) Please connect first harddisk to IDE1 and connect CDROM to IDE2. The red stripe of the ribbon cable must be the same side with the Pin1. 6) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD.
Page 16
HD (IDE Hard Disk Active LED) SPK (Speaker Connector) RST (Reset Switch) PW (Soft Power Connector) MPD(Message LED/Power/ Sleep LED) 8S651M-RZ Series Motherboard So ft Pow er Spea ker Co nnector Me ssa g e LED /Po w e r / Conne ctor...
Page 17
9 ) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. If you use dual color LED, power LED will turn to another color. 10) BAT (Battery) Pin No.
Page 18
12) SUR_CEN Please contact your nearest dealer for optional SUR_CEN cable. 13) CD_IN Connect CD-ROM or DVD-ROM audio out to the connector. 8S651M-RZ Series Motherboard Pin No. Definition POWER FrontAudio(R) RearAudio(R)
Page 19
14) SPDIF_IO (SPDIF In/Out) The SPDIF output is capable of providing digital audio to external speakers or compressed AC3 data to an external Dolby Digital Decoder. Use this feature only when your stereo system has digital input function. Use SPDIF IN feature only when your device has digital output function. Be careful with the polarity of the SPDIF_IO connector.
Page 20
You may clear the CMOS data to its default values by this jumper. To clear CMOS, temporarily shor 1-2 pin. Default doesn't include the "Shunter" to prevent from im proper use this jumper. 8S651M-RZ Series Motherboard Pin No. Definition NDCDB-...
Chapter 2 BIOS Setup BIOS Setup is an overview of the BIOS Setup Program. The program that allows users to modify the basic system configuration. This type of inform ation is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. ENTERING SETUP Powering ON the com puter and pressing <Del>...
Page 22
Change, set, or disable password. It allows you to lim it access to the system. • Save & Exit Setup Save CMOS value settings to CM OS and exit setup. • Exit Without Saving Abandon all CMOS value changes and exit setup. 8S651M-RZ Series Motherboard - 22 -...
Standard CMOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Date (mm:dd:yy) Time (hh:mm:ss) } IDE Primary Master } IDE Primary Slave } IDE Secondary Master } IDE Secondary Slave Drive A Drive B Floppy 3 Mode Suport Holt On Base Memory Extended Memory Total Memory...
Page 24
640K for systems with 640K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the am ount of mem ory located above 1 M B in the CPU's memory address map. 8S651M-RZ Series Motherboard - 24 -...
Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2004 Award Software First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Password Check higf : Move Enter: Select F5: Previous Values First / Second / Third Boot Device Floppy Select your boot device priority by Floppy.
Enable onboard 2nd channel IDE port. (Default value) Disabled Disable onboard 2nd channel IDE port. AC97 Audio Enabled Enable onboard AC'97 audio function. (Default value) Disabled Disable this function. "*" For 8S651M-RZ only. 8S651M-RZ Series Motherboard Integrated Peripherals [Auto] Item Help [Auto] Menu Level u [Enabled]...
Page 27
Enable onboard LPT port and address is 378/IRQ7. (Default Value) 278/IRQ5 Enable onboard LPT port and address is 278/IRQ5. Disabled Disable onboard LPT port. 3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7. "*" For 8S651M-RZ only. Set onchip VGA shared memory size.(Default Value:32MB) - 27 - BIOS Setup...
Day (of Month) x Time (hh:mm:ss) Power LED in S1 state higf : Move Enter: Select +/-/PU/PD: Value F5: Previous Values F6: Fail-Save Default 8S651M-RZ Series Motherboard Power Management Setup [S1(POS)] Item Help [Off] Menu Level u [Off] [S1]...
Page 29
ACPI Suspend Type S1(POS) Set ACPI suspend type to S1. (Default Value) S3(STR) Set ACPI suspend type to S3. Soft-off by PWR_BTTN The user press the power button once, he can turn off the system. (Default Value) Suspend The user press the power button once, then the system will can enter suspend mode.
PCI Health Status CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Reset Case Open Status Case Opened VCORE +3.3V +12V Current System Temperature Current CPU Temperature Current CPU FAN Speed Current SYSTEM FAN Speed CPU Warning Temperature CPU FAN Fail Warning SYSTEM FAN Fail Warning higf : Move Enter: Select...
If you use DDR200 DRAM module, please set "DRAM Clock(MHz)" to 200. If you use DDR333 DRAM module, please set "DRAM Clock(M Hz)" to 333. Incorrect using it may cause your system broken. For power End-User use only! 8S651M-RZ Series Motherboard Frequency/Voltage Control [10X]...
AGP Clock (MHz) Please set AGP Clock according to your requirem ent. Incorrect using it may cause your system broken. For power End-User use only! PCI Clock (MHz) Please set PCI Clock according to your requirem ent. Incorrect using it may cause your system broken. For power End-User use only! Top Performance CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features...
Setup M enu. If you select "Setup" at "Password Check" in Advance BIOS Features Menu, you will be prompted only when you try to enter Setup. 8S651M-RZ Series Motherboard Top Performance Load Fail-Safe Defaults...
Save & Exit Setup CMOS Setup Utility-Copyright (C) 1984-2004 Award Software Standard CMOS Features Advanced BIOS Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status Frequency/Voltage Control ESC: Quit F8: Q-Flash Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. Type "N"...
"GO" button. The by itself. We recommend that you install all com ponents in the list. 8S651M-RZ Series Motherboard to install the drivers automatically. Massage: Some device drivers will restart your system autom atically. After restarting your system the "Xpress Install"...
Page 37
XP and Windows 2000 only. Once we get the latest SiS put the driver on GIGABYTE website asap. (http://www.gigabyte.com.tw). For USB2.0 driver support under Windows XP operating system, please use Windows Service Pack. After install Windows Service Pack, it will show a question mark "?" in "Universal Serial Bus controller"...