Mitsubishi Electric FR-F820-04750 Instruction Manual page 389

Parameters
Output signal list
● The functions of the output terminals can be set.
● Refer to the following table and set each parameter.
(0 to 99: Positive logic, 100 to 199: Negative logic)
Setting
Positive
logic
0
1
2
3
4
5
7
8
10
11
12
13
14
15
16
17
18
19
25
26
35
39
40
Tab. 5-101: Output terminal function assignment (1)
FR-F800
Signal
Function
Negative
name
logic
100 RUN Inverter running
101 SU
Up to frequency
Instantaneous power
102 IPF
failure/undervoltage
103 OL Overload warning
Output frequency
104 FU
detection
Second output frequency
105 FU2
detection
107 For manufacturer setting. Do not set.
Electronic thermal O/L
108 THP
relay pre-alarm
110 PU PU operation mode
111 RY Inverter operation ready
112 Y12 Output current detection
113 Y13 Zero current detection
114 FDN PID lower limit
115 FUP PID upper limit
PID forward/reverse
116 RL
rotation output
⎯
MC1 Electronic bypass MC1
⎯
MC2 Electronic bypass MC2
⎯
MC3 Electronic bypass MC3
125 FAN Fan fault output
Heatsink overheat pre-
126 FIN
alarm
135 TU Torque detection
Start time tuning
139 Y39
completion
140 Y40 Trace status
(M) Monitor display and monitor output signal
Operation
Output during operation when the
inverter output frequency reaches Pr. 13
"Starting frequency" or higher.
Output when the output frequency
reaches the set frequency.
Output when an instantaneous power
failure or undervoltage protection
operation occurs.
Output during operation of the stall
prevention function.
Output when the output frequency
reaches the frequency set in Pr. 42 (Pr. 43)
during reverse rotation) or higher.
Output when the output frequency
reaches the frequency set in Pr. 50 or
higher.
Output when the cumulative electronic
thermal O/L relay value reaches 85% of
the trip level. (Electronic thermal O/L
relay protection (E.THT/E.THM) is
activated when the value reaches 100%.)
Output when PU operation mode is
selected.
Output when the reset process is
completed after powering ON the
inverter (when starting is possible by
switching the start signal ON or during
operation).
Output when the output current is
higher than the Pr. 150 setting for the
time set in Pr. 151 or longer.
Output when the output current is lower
than the Pr. 152 setting for the time set in
Pr. 153 or longer.
Output when the value is lower than the
lower limit of PID control.
Output when the value is higher than the
upper limit of PID control.
Output during forward rotation under
PID control.
Used when using the electronic bypass
function.
Output when a fan fault occurs.
Output when the heatsink temperature
reaches about 85% of the heatsink
overheat protection operation
temperature.
Output when the motor torque is higher
than the Pr. 864 setting.
Output when tuning is completed during
start-up.
Output during trace operation.
Related Refer to
parameter page
⎯
5-232
Pr. 41 5-234
5-409,
Pr. 57
5-417
Pr. 22, Pr. 23,
Pr. 66, Pr. 148, 5-175
Pr. 149, Pr. 154
Pr. 42, Pr. 43 5-234
Pr. 50 5-234
Pr. 9 5-145
Pr. 79 5-116
⎯
5-232
Pr. 150, Pr. 151 5-238
Pr. 152, Pr. 153 5-238
Pr. 127 to
Pr. 134,
5-347
Pr. 575 to
Pr. 577, Pr.1370
Pr. 135 to
5-327
Pr. 139, Pr. 159
Pr. 244 5-155
⎯
6-20
Pr. 864 5-240
Pr. 95, Pr. 574 5-321
Pr. 1020 to
5-437
Pr. 1047
5 - 227