Operations; Listening To A Program Source - Sherwood Newcastle R-956 Operation Instructions Manual

Operations

Note : Before operating this receiver with the supplied remote control, refer to "Universal Remote Control" on page 10 for
details about operation.
L I S T E N I N G T O A P R O G R A M
Before operation
Enter the standby mode.
The STANDBY button lights up in red.
This means that the receiver is connected to the AC
mains and a small amount of current is retained to
support the memorized contents and operation
readiness.
To switch the power completely off, push the
POWER switch again.
The power is cut off and the STANDBY light goes
off.
In the standby mode, turn the power on.
1
STANDBY
ON/STANDBY
or
Each time the STANDBY button on the front panel or
the POWER button on the remote control is pressed,
the receiver turns on to enter the operating mode(the
STANDBY button lights up in green) or turns off to
enter the standby mode (the STANDBY button lights
up in red).
In the standby mode, if one of the INPUT
SELECTOR buttons is pressed, the receiver turns on
automatically and the desired input is selected.
Switch the speakers on.
2
The SPEAKER indicator lights up on the display and
sound can be heard from the speakers connected to the
speaker terminals.
When using headphones for private listening, press the
SPEAKER button again to switch the speakers off.
MAIN POWER
ON / OFF
PWR
AUD AUD CD DVD AUX
SAT SAT TV VCR CBL
PWR
1 2 3
4 5 6
TAPE MONITOR function
7 8 9
MUTE 0 CH SEL
P.SCAN
You can connect either a tape deck or a graphic equalizer
SLEEP
VOL VOL CH LEVL
T.TONE
D.TIME D.ADJ
to the receiver's TAPE MONITOR jacks.
ENTER
OSD
AUTO STEREO
To listen to the component connected to these jacks, set the
DSP MODE 6.1CH IN C.MODE
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
TAPE MONITOR button to on.
VID 4 VID 4 AUX ROOM 2 SYS DISP
HOME THEATER MASTER
RNC-30 If you connect a 3-head tape deck, you can monitor the
actual recording, not the source sound.
For further details, refer to the operating instructions of
the component connected.
SPEAKER
ON/OFF
1 4
Select the desired input source.
3
INPUT SELECTOR
AUDIO VIDEO
TAPE MON.
PHONO CD TUNER
AUX
or
VID SEL
AUX
Each time the "AUDIO" button is pressed, the input
source changes as follows;
PHONO TUNER CD PLAYER
(frequency display)
Each time the "VIDEO" or "VID SEL" button is
pressed, the input source changes as follows;
VIDEO 1 VIDEO 2 -----
When the TAPE MONITOR button is set to ON so
that "TAPE MON" lights up, other inputs can not be
heard from the speakers.
To listen to an input source other than TAPE MONITOR,
be sure to set the TAPE MONITOR button to off.
When selecting the 6.1 CH DIRECT as desired
PWR
AUD AUD CD DVD AUX
SAT SAT TV VCR CBL
1 2 3
4 5 6
6.1CH DIRECT
7 8 9
MUTE 0 CH SEL
P.SCAN
SLEEP
VOL VOL CH LEVL
T.TONE
D.TIME D.ADJ
or
ENTER
OSD
AUTO STEREO
DSP MODE 6.1CH IN
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
VID 4 VID 4 AUX ROOM 2 SYS DISP
HOME THEATER MASTER
RNC-30
6.1 CH DIRECT is displayed and the 7 separate
analog signals from a decoder or DVD player
connected to this unit will be heard. You can use the
tone controls and volume control to adjust the signal.
(If the TAPE MONITOR button is to on, it will
automatically be set to off.)
To cancel the 6.1 CH direct function, press the 6.1 CH
DIRECT button again or select the desired input
source.
These 7 separate analog signals can be heard, only.
They cannot be recorded.
PWR
AUD AUD CD DVD AUX
SAT SAT TV VCR CBL
1 2 3
4 5 6
7 8 9
MUTE 0 CH SEL
P.SCAN
SLEEP
VOL VOL CH LEVL
T.TONE
D.TIME D.ADJ
TAPE MON
ENTER
OSD
AUTO STEREO
DSP MODE 6.1CH IN
PHONO CD TUNER TAPE MON
T2 MON VID SEL VID 2 VID 3
VID 4 VID 4 AUX ROOM 2 SYS DISP
HOME THEATER MASTER
RNC-30
AUX
VIDEO 5
6.1CH IN