Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 31213
  6. Manual

Toro 31213 Manual

Hide thumbs Also See for 31213:

Advertisement

Quick Links

Download this manual
60in Blower Kit
Groundsmaster
Model No. 31213—Serial No. 402620001 and Up
Use of this product may cause exposure to chemicals known to the State of California
to cause cancer, birth defects, or other reproductive harm.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
© 2018—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
360 and 7200 Series Tripple Bagger Hopper
Proposition 65 Warning
133-8061
Register at www.Toro.com.
WARNING
CALIFORNIA
decal133-8061
Form No. 3428-559 Rev A
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3428-559* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro 31213

Summary of Contents for Toro 31213

  • Page 1 Form No. 3428-559 Rev A 60in Blower Kit Groundsmaster ® 360 and 7200 Series Tripple Bagger Hopper Model No. 31213—Serial No. 402620001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning Use of this product may cause exposure to chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

  • Page 2: Preparing The Machine

    Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Double pulley assembly Install the pulley assembly. Remove the existing anti-scalp roller – No parts required and bracket (for 60-inch decks only).
  • Page 3 Installing the Pulley Assembly Parts needed for this procedure: Double pulley assembly Procedure g033896 Figure 2 Lower the mower deck to the lowest height-of-cut position. 1. Pulley nut 3. Double pulley assembly Remove the right belt cover (Figure 2. Washer 4.
  • Page 4 Removing the Existing Installing the Blower Hinge Anti-Scalp Roller and Parts needed for this procedure: Bracket Blower hinge (For 60-inch Decks Only) Metal template 3 or 4 Bolt (3/8 x 1 inch) 3 or 4 Locknut (3/8 inch) No Parts Required Procedure Procedure Clean the area around the right, rear anti-scalp...
  • Page 5 Figure 2. Bolt (3/8 x 1 inch) 5. Drilled holes 3. Locknut (3/8 inch) Model 31213 Install the metal template to the mower deck with the previously removed carriage bolts and nuts using the existing holes in the mower deck...
  • Page 6 Routing the Blower Belt into the Blower Assembly Parts needed for this procedure: Blower belt Spring Procedure g011056 Figure 7 If present, cut the existing belt cover bracket 1. Mower deck 4. Bolt (3/8 x 4-1/2 7. Bushing so that it is flush with the edge of the top deck inch) assembly;...

  • Page 7: Installing The Blower Assembly

    WARNING g011124 An uncovered discharge opening could allow Figure 11 the mower to throw objects toward you or Model 31213 shown bystanders, resulting in serious injury. Also, contact with the blade could occur. 1. Blower assembly 3. Pivot hole 2. Mower deck 4.
  • Page 8 Figure 12 Figure 14 Model 31213 shown 1. Mower deck pulley 3. Blower 2. Spring-loaded Idler pulley 1. Latch 3. Blower assembly 2. Bolt Tighten the latch bolts. Install the spring as shown in Figure Note: Make sure that the hooks are in the correct position.
  • Page 9 Bolt Parts needed for this procedure: Belt cover Bolt (1/2 x 2-1/2 inches) Nut (1/2 inch) g011051 Figure 16 Model 31213 Procedure 1. Knob 3. Mower deck Lower the mower deck to the lowest height-of-cut 2. Belt cover position.
  • Page 10 Installing the Blower Installing the Tube Latch Guards Parts needed for this procedure: Latch bracket assembly Parts needed for this procedure: Bolt (3/8 x 2-1/2 inches) Front guard Nut (3/8 inch) Back guard Latch bracket strap Bolt (1/4 x 5/8 inch) Screw (#10 x 1/2 inch) Nut (1/4 inch) Nut (#10)
  • Page 11 Installing the New Belt Cover Bracket Upon Removal of the Kit (For Model 31212 Only) g033957 Figure 20 Parts needed for this procedure: 1. Screw (#10 x 1/2 inch) 3. Nut (#10) Belt cover bracket 2. Latch-bracket strap Carriage bolt (1/4 x 3/4 inch) Locknut (1/4 inch) Procedure Drill 2 holes (0.266 inch or drill size H) into the...
  • Page 12 g033987 Figure 22 1. Locknut (1/4 inch) 3. New belt cover bracket 2. Drilled hole 4. Carriage bolt (1/4 x 3/4 inch) g012500 Figure 23 1. Throttle stop 3. Speed-control lever 2. Nut and washer Insert the throttle stop onto the governor shaft so Installing the Throttle Stop the tab rests against the flat on the speed-control lever...
  • Page 13 Notes:...
  • Page 14 Notes:...
  • Page 15 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.
  • Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.