Advertisement
Quick Links
60in and 72in Blower Kit
Groundsmaster
Model No. 31212—Serial No. 316000001 and Up
Model No. 31213—Serial No. 316000001 and Up
This product contains a chemical or chemicals known to the State of California to
Note: Determine the left and right sides of the machine from the normal operating position.
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
360 and 7200 Series Triple Bagger Hopper
Proposition 65 Warning
cause cancer, birth defects, or reproductive harm.
Description
No parts required
Double pulley assembly
No parts required
Blower hinge
Metal template
Bolt (3/8 x 1 inch)
Locknut (3/8 inch)
Blower belt
Spring
Blower assembly
Belt cover
Bolt (1/2 x 2-1/2 inches)
Nut (1/2 inch)
Front guard
Back guard
Bolt (1/4 x 5/8 inch)
Nut (1/4 inch)
Latch bracket assembly
Bolt (3/8 x 2-1/2 inches)
Nut (3/8 inch)
Latch bracket strap
Screw (#10 x 1/2 inch)
Nut (#10)
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
1
–
1
1
3 or 4
3 or 4
1
1
1
1
1
1
1
1
6
1
1
2
2
1
2
2
Form No. 3405-720 Rev A
Installation Instructions
Use
Prepare the machine.
Install the pulley assembly.
Remove the existing anti-scalp roller
and bracket (for 60-inch decks only).
Install the blower hinge.
Route the blower belt into the blower
assembly.
Install the blower assembly.
Install the belt cover and bolt.
Install the blower guards.
Install the tube latch.
Original Instructions (EN)
All Rights Reserved *3405-720* A
Printed in the USA
Advertisement
Related Manuals for Toro 31212
Summary of Contents for Toro 31212
- Page 1 Form No. 3405-720 Rev A 60in and 72in Blower Kit Groundsmaster ® 360 and 7200 Series Triple Bagger Hopper Model No. 31212—Serial No. 316000001 and Up Model No. 31213—Serial No. 316000001 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
-
Page 2: Preparing The Machine
Procedure Description Qty. Belt cover bracket Install the new belt cover bracket upon Carriage bolt (1/4 x 3/4 inch) removal of the kit (for model 31212 only). Locknut (1/4 inch) Throttle stop Install the throttle stop. Preparing the Machine Installing the Pulley Assembly... - Page 3 7. After the new pulley assembly is in position, install the mower deck belt onto the lower pulley. Removing the Existing Anti-Scalp Roller and Bracket (For 60-inch Decks Only) No Parts Required Procedure 1. Clean the area around the right, rear anti-scalp wheel. 2.
- Page 4 3 or 4 Bolt (3/8 x 1 inch) 3 or 4 Locknut (3/8 inch) Procedure Model 31212 Figure 4 1. Install the metal template to the mower deck with the previously removed carriage bolts and nuts using the 1. Mower deck 4.
- Page 5 2. Center punch the new mower deck hole locations using the 3 holes in the template (Figure 3. Remove the metal template and drill 3 pilot holes (1/8 inch) with a sharp drill bit (Figure 4. Drill 3 holes (13/32 inch) holes into the pilot holes with a sharp drill bit (Figure Figure 7...
-
Page 6: Installing The Blower Assembly
Routing the Blower Belt into the Blower Assembly Parts needed for this procedure: Blower belt Spring Figure 9 Procedure 1. Idler pulley 4. Peg 1. If present, cut the existing belt cover bracket so that it 2. Mower deck pulley 5. - Page 7 Figure 12 Model 31213 shown Figure 10 1. Latch 3. Blower assembly 1. Bolt 5. Spring installed 2. Bolt 2. Spacer 6. Grass deflector 3. Locknut 7. L-end of spring; place it behind the deck edge 4. Install the spring as shown in Figure before installing the bolt.
- Page 8 Figure 15 Figure 14 Model 31212 1. Mower deck pulley 3. Blower 1. Belt cover 3. Nut 2. Spring-loaded Idler pulley 2. Hairpin assembly Tighten the latch bolts. Installing the Belt Cover and Bolt Parts needed for this procedure: Belt cover...
- Page 9 Installing the Blower Guards Parts needed for this procedure: Front guard Back guard Bolt (1/4 x 5/8 inch) Nut (1/4 inch) Figure 17 Procedure 1. 152 mm (6 inch) 3. Bolt (1/2 x 2-1/2 inches) 1. Install the front guard using 3 bolts and a nut (1/4 height-of-cut hole inch);...
- Page 10 Installing the Tube Latch Parts needed for this procedure: Latch bracket assembly Bolt (3/8 x 2-1/2 inches) Nut (3/8 inch) Figure 20 Latch bracket strap 1. Screw (#10 x 1/2 inch) 3. Nut (#10) Screw (#10 x 1/2 inch) 2. Latch-bracket strap Nut (#10) Procedure 1.
- Page 11 Installing the Throttle Stop Bracket Upon Removal of the For CE Compliant GM7200 or GM7210 International Machines with Kubota Engines (For Model 31212 Only) Parts needed for this procedure: Parts needed for this procedure: Throttle stop Belt cover bracket Carriage bolt (1/4 x 3/4 inch)
- Page 12 Notes:...
- Page 13 Notes:...
- Page 14 Notes:...
- Page 15 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 16 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.